Frigidaire FPHB2899LF5 Use & Care Manual page 13

To avoid electric shock, which can cause
death or severe personal injury, disconnect
the refrigerator from electrical power before
connecting a water supply line to the refrigerator.
To Avoid Property Damage:
• Copper or Stainless Steel braided tubing is
recommended for the water supply line. Water
supply tubing made of ¼ inch plastic is not
recommended to be used. Plastic tubing greatly
increases the potential for water leaks, and the
manufacturer will not be responsible for any
damage if plastic tubing is used for the supply line.
• DO NOT install water supply tubing in areas
where temperatures fall below freezing.
• Chemicals from a malfunctioning water
softener can damage the ice maker. If your
home has a water softening system, ensure the
.................... softener is maintained and working properly, .............................
Ensure that your water supply line connections comply
with all local plumbing codes.
Before Installing The Water Supply Line, You Will Need:
* Basic Tools: adjustable wrench, flat-blade
screwdriver, and PhillipsTMscrewdriver
* Access to a household cold water line with water
pressure between 30 and 100 psi.
* A water supply line made of 1/4inch (6.4 ram) OD,
copper or stainless steel tubing. To determine the
length of tubing needed, measure the distance
from the ice maker inlet valve at the back of the
refrigerator to your cold water pipe. Then add
approximately 7 feet (2.1 meters), so the refrigerator
can be moved out for cleaning (as shown).
* A shutoff valve to connect the water supply line to
your household water system. DO NOT use a self-
piercing type shutoff valve.
* Do not re-use compression fiWng or use thread sealtape.
* A compression nut and ferrule (sleeve) for connecting
a copper water supply line to the ice maker inlet valve.
To Connect Water Supply Line To Ice Maker Inlet Valve
,
2.
Disconnect refrigerator from electric power source,
Place end of water supply line into sink or bucket,
Turn ON water supply and flush supply line until
water is clear, Turn OFF water supply at shutoff
valve.
3. Remove plastic cap from water valve inlet and
discard cap.
4. If you use copper tubing - Slide brass
compression nut, then ferrule (sleeve) onto water
supply line. Push water supply line into water valve
inlet as far as it will go (1/4 inch/6.4 mm). Slide
ferrule (sleeve) into valve inlet and finger tighten
compression nut onto valve. Tighten another half
turn with a wrench; DO NOT over tighten. See
Figure 1.
If you use stainless steel tubing - The nut and
ferrule are already assembled on the tubing. Slide
compression nut onto valve inlet and finger tighten
compression nut onto valve. Tighten another half
turn with a wrench; DO NOT over tighten. See
Figure 2.
5. With steel clamp and screw, secure water
supply line (copper tubing only) to rear panel of
refrigerator as shown.
6. Coil excess water supply line (copper tubing only),
about 21/2turns, behind refrigerator as shown and
arrange coils so they do not vibrate or wear against
any other surface.
7. Turn ON water supply at shutoff valve and tighten
any connections that leak.
8. Reconnect refrigerator to electrical power source.
to ice Maker
Steel
Clamp
Brass
Compression
Ferrule
Copper
water,no
_er Valve
Bracket
_===_Valve inlet
e
Copper water line
frora hoasel_oid wat#r Supply
h tubing in loop to allow
moving refrigerator out for cleaning.)
Figure 1 Figure 2
Check with your local building authority for
recommendations on water lines and associated materials
prior to installing your new refrigerator, Depending on
your local/state building codes, Frigidaire recommends for
homes with existing valves its Smart Choice® water line kit
5305513409 (with a 6 f_. Stainless Steel Water Line) and
for homes without an existing valve, Frigidaire recommends
its Smart Choice® water line kit 5305510264 (with a 20 f_.
Copper Water Line with self-tapping saddle valve). Please
refer to www.frigidaire.com/store for more information.
Af[er connecting _e water supply, refer to "How to Prime
the Water Supply System" for important information about
priming an empty water supply system.
Your refrigerator'swater supply system includes several tubing
lines, a water filter, a water valve, and a water tank. To ensure
that your water dispenser works properly, this system must
be completely filled with water when your refrigerator is first
connected to _e household water supply line.