Advertisement
Quick Links
Save This Manua! For
Futu re Reference
MO
L
O.
113.235500
Serial
Number
Model and serial number may be
found attached to the underside of
the worktable.
You should record both model and
serial number in a safe place for
future use.
FOR YOUR
SAFETY:
Read ALL
INSTRUCTIONS
carefully
!61
CH SCROLL SAW
, assembly
. operating
. repair parts
Sold by SEARS, ROEBUCK
AND CO., Chicago,
IL 60684 U.S.A.
Part No. SP5639
Printed in
USA
Advertisement
Related Manuals for Craftsman 113.235500
Summary of Contents for Craftsman 113.235500
- Page 1 Save This Manua! For Futu re Reference 113.235500 Serial Number Model and serial number may be found attached to the underside of the worktable. You should record both model and serial number in a safe place for future use. CH SCROLL SAW FOR YOUR SAFETY: , assembly...
- Page 2 IAN SCROLL i Saw fails due to a defect In RETURNING THE CRAFTSMAN SCROLL SERVICE CENTER/DEPARTMENT IN THE APPLIES ONLY WHILE THIS PRODUCT IS USED IN THE UNITED STATES. Th_s:Wttrranty gives you specific tegat: rights and you may also have other rights which vary from state to state.
- Page 3 • Use this scroll saw to cut only wood, woodqike CHECK DAMAGED PARTS. Check for: products, plastics and nomferrous metals. • Alignment of moving parts. • Binding of moving parts. CAUTION: This designed • Broken pads. cutting ferrous metals like iron or steel. When cutting non-ferrous metals (brass,...
- Page 4 safety instru cti 0ns, for scro m l SSIW shaped workpieces; plan When backing up the workpiece, blade !:_/;; y 0ur_workso;iitwiil_-_Ot_ pinch: the :blad& A piece Of bind in the kerf (cut), This usually :::::_':_iiolding; for examplei rnust :lay flat orbe heid by a Caused sawdust...
- Page 5 motor specifications and electricaJ requirements This machine is equipped with, a 1725 RPM motor. WARNING: Do not permit fingers to touch the wired operation 120V, 60Hz, alternating current. terminals of pJug when installing or removing the plug to or from the outlet.
- Page 6 glossary of terms woodworking Kerr - the slot cut by the blade. Blade Tooth Set -the distance that the edge of the sawblade tooth is bent (or set) outward Leading Edge - the edge of the workpiece from the side of the blade. which is pushed into the blade first.
- Page 7 DO NOT LIFT SAW BY ]'HIS LIFT HERE assembly WARNING: your safety, never connect plug to power source outlet L_ntit all assembly steps are complete, and you have read and understand the safety and operating instructions. Lift the saw by the frame and base and place scroll saw on work bench 2_ Famiharize yourse!f with the controls features of this scroll saw indicated in the...
- Page 8 assernbmy SETTING THE TABLE FOR HOR|ZONTAL OR BEVEL CUTTING The scroll saw work table can be tilted to the left bevel cutting up to 45 ° from 0 ° or horizontal cutting position. A bevel scale is provided under the work table as a convenient reference for setting the approximate...
- Page 9 Use a small square to set the table at 90 ° to the blade. If there is too much space between the square and the blade, the table must be adjusted. When the space between the square and the blade is minimal, tighten the bevel lock knob_ The table should now be approximately 90 °...
-
Page 10: Removing And Installing Blades 1
removing and installing blades WARNING: To avoid injury from accidenta! starting, always turn switch "OFF" and remove switch key before removing or replacing blade. N KNOB Loosen tension on blade by turning tension knob counterclockwise ) about three full turns. Remove blade by pulling torward... -
Page 11: Operation
Locate the blade guard and carefully install it onto the saw as shown. Lightly spread apart the blade guard so pins will go into holes in frame. In order to cut, and to avoid uncontrollable lifting of the workpiece, the teeth of the blades used on the scroll saw should always point downward when installed on the scroll saw. - Page 12 a bench mounting the scromlsaw to When mounting this saw to a workbench a solid wood bench is preferred over a plywood bench where SCROLL SAW BASE noise and vibration will be more noticeable. Hardware to mount this saw to a workbench is HEX HEAD SCREW_ supplied with the saw.
- Page 13 know your scroll getting 1. TENSION Kt 2. BLADE HOLDER 3. BLADE GUARD ON-OFF SWITCH TABLE LOCK KNOB 7. BEVEl 6. BEVEL POINTER INTENDED HELP PREVENT TENSION KNOB Tightening knob UNAUTHORIZED POSSIBLY HAZARDOUS (clockwise) wilt increase the tension of the blade. BY CHILDREN OTHERS.
- Page 14 getting to know your scroll To turn machine "ON", place finger under switch lever and PULL end of switch out, To turn machine "OFF", PUSH lever in. Never leave the machine unattended until it come to a stop. PUSH To lock switch in "OFF" position, hold switch with one hand, REMOVE key with other hand.
- Page 15 operation of your scroll To get accurate cuts, prepared to compensate PLEASE, read understand the following items blades' tendency to follow wood grain as you are about your scroll before attempting to use the saw. cutting This scroll is intended to cut wood or wood The saw does not cut wood by itseff.
- Page 16 basic saw operations Do not wear loose clothing, gloves, neckties or • Make sure the bevel lock knob is tight and no parts jewelry (rings, wristwatches). They can get caught have excessive play, and draw you into moving parts. • To avoid accidental blade contact, minimize blade Wear non-slip footwear.
- Page 17 DON'T OVERREACH. Keep good footing and balance. • Unplug saw. Keep your face and body to one side of blade, out of line • Wait for all moving parts to stop. with a possible thrown piece if the blade should break. When backing workpiece,...
-
Page 18: Maintenance
maintenance WARNING: For your own safety, turn switch "OFF", remove remove plug from power source outlet before maintaining lubricating your saw, GENERAL An occasional coat of paste wax on the work table will allow the wood being cut to glide smoothly across the work surface. -
Page 19: Trouble Shooting
Sears recommends the following accessories Item Sears Number Sears may recommend other accessories not listed in manual. See your nearest Sears Store or Catalog !Leg Set ............9-22244 Department for other accessories. Blades ....... See Catalog - For 5" long, Pin end type blades Plain End Blade Adapter ...... - Page 20 "0 }> ¢.) rl"l "1"I }> ,..,L...
- Page 21 SCROLL LiST CRAFTSMAN 164NCH MOTORIZED PARTS MODEL 113.235500 FIGURE Always Order By Part Number-Not By Key Number Part Part De scr_tion Description Guard, Blade 821526 Washe r, 17/64 x3!4x7i64 STD551025 821 447-1 Housing (Includes Key #3) Scale, Bevel 82 t 522...
- Page 22 16 INCH SCROLL owners manual SERVmCE Now that you have purchased your scroll saw, should need ever exist for repair parts or service, simply contact Sears Service Center and most Sears, Roebuck stores. Be sure provide pertinent facts when you call or visit. MODEL NO, The model number of your scroll saw will be found...