Table of Contents
Advertisement
Future Reference
Serial
Number
Model and serial number may be
found attached to the right side of
housing.
You should
record both
model
and serial number in a safe place
for future use.
FOR YOUR
SAFETY:
READ ALL
INSTRUCTIONS
CAREFULLY
,
S/CRRFT3M
SCROLL
• assembly
o operati
. repair parts
Sears, Roebuck and Co., Hoffman
Estates,
ILo 60179 U.S.A.
Part No. SP5693
Printed in U.S.A
Advertisement
Table of Contents
Related Manuals for Craftsman 113.235501
Summary of Contents for Craftsman 113.235501
- Page 1 FOR YOUR SAFETY: READ ALL INSTRUCTIONS CAREFULLY Sears, Roebuck and Co., Hoffman Part No. SP5693 S/CRRFT3M SCROLL • assembly o operati . repair parts Estates, ILo 60179 U.S.A.
- Page 2 • Support the saw so the table is level and the saw does not rock. - Bolt the saw to the work surface if it tends to slip, walk, or slide during operations like cutting boards, or when using an auxiliary table.
- Page 3 If any part is missing, bent or broken or any electrical parts don't work properly, turn the saw off and unp]ug the saw REPLACE missing or faited parts before using the saw again KEEP GUARD IN PLACE and in working order MAINTAIN TOOLS WITH CARE.
- Page 4 [tme • Clear eveL=hin exce t the work iece and support dev ces off the table before turn ng the saw on. Plan the way you will hold the workpiece from start to finish, Do not hand hold pieces so small that your fingers will go under the blade guard.
- Page 5 If you are not sure that you outlet, as pictured below, is properly grounded, have it checked by a qualified electri- cian.
- Page 6 Repair Parts ... Notes ... Service MEDIUM FLAT BLADE SCREWDRIVER If any safety never assemble the Scroll Saw, plug m the power cord or turn the and you have obtained safety Table of Loose Parts A 16" Scroll Saw ...
- Page 7 Lift the saw by the frame and base and place scroll saw on work bench Familiarize yourself with the controls and features of this scroll saw indicated in the illustration.
- Page 8 bevel: cutting 45 ° from hor zontal cuttng positioni A bevel scale is provided under the work table as a bonvenient reference for setting the approximate :table angle for bevel cutling. When greater precision is required, make practice cuts and adjust the table as necessary ;requirementS:...
- Page 9 Use a small square to set the table at 90 ° to the blade. I! there is too much space between the square and the blade, the table must be adjusted. When the space between the square blade is minimal, tighten the bevel lock knob, table should now be approximately Loosen screw...
- Page 10 Cutting from the side of the saw will be necessary when your workpiece exceeds 16 inches in length.
- Page 11 In order to cut, and to avoid uncontrollable the workpiece, the teeth of the blades scroll saw should always point downward when installed on the scroll saw. Install the blade by inserting one end of the blade through the slot in the blade guard, then the access hole in the table, until you can hook the blade pin in the pin recess in the bottom blade holder.
- Page 12 :NOT Over tighten mounting bolts - leave some . ::: Cushion in the foam pad for absorbing Vibration: 4_: If you prefer to mount y0ur saw to aleg set, we rec- ommend the leg set for bench top tools which is available through Sears Retail Stores.
- Page 13 U saw 1. TENSION TENSION KNOB Tightening _cIockwise) will increase the tension of the blade. Loosening it (counterclockwise) tension. BLADE HOLDER Retain and position the blade. BLADE GUARD .., Provides added control of workpiece by bearing directly...
- Page 14 Remove key and keep it in a safe place, Also, in the event of a power failure (all of your lights out):turn switch off, remove the key and store it remote from the scroll saw. This will prevent the :machine from starting up again when the power comes back on.
- Page 15 • Narrower blades work well only on thinner material. 11. This saw uses 5 inch long, pin end type, blades only. See your Sears Retail Store for accessory blades. 12. Blades wear faster when cutting plywood, which is very abrasive; when sawing wood which is thicker than the 7/8 inch blade stroke;...
- Page 16 They are not safety glasses. Safety goggles are available at Sears Retail or Catalog Stores. Glasses or goggles not in compliance with ANSI Z87.1 could seriously hurt you when they break. • Do not wear loose clothing, jewelry (rings, wristwatches).
- Page 17 Remove switch key. MAKING gNTERtOR SCROLL One of the features of this saw is that it can be used to make scroll cuts on the interior of a board without breaking or cutting into the outline or perimeter of the board, WARNING:...
- Page 18 Lubricate the arm bearings after 10 hours of use. Re-oil after every 50 hours of use or whenever th ere is a squeak coming irom the bearings. Turn saw on its side. Squirt a generous amount of SAE 30 oil around the shaft end and bronze bearing.
- Page 19 Sears Number Sears may recommend 9-22244 manual. See your nearest Sears store for other accesso- ries. Do not use any accessory unless you have received and 9-22257 read complete instructions for its use. for this saw. Using other accessories ARNING: Use only accessories gerous.
- Page 20 40" "1'1...
- Page 21 66052 Indicator, Tilt Slandard hardware item - may be purchased locally. 1 Stock item - may be secured through the Hardware department of most Sears Retail Stores 16-INCH MOTOI_IZED SCROLL FIGURE 1 Always Order By Part Number-Not By Key Number...
- Page 22 Call 24 hours a day, 7 days a week 1-800-4-REPAIR (1-800-473-7247) For the location of a Sears Repair Service Center in your area Call 24 hours a day, 7 days a week 1-800-488-122:2 For information on purchasinga Sears Maintenance Agreement or to inquire...