Advertisement
Available languages
Available languages
ASSEMBLY
Installing Wheels, Handles, Molded
FootBumi:_
THE WHEELS
AND HANDLE
DO NOT PRO-
V_DE ADEQUATE
CLEARANCE,
STAB1UTY
L;_ :_. : , L RT FOR PULUNG
THE UNiT UP
AND D©WN S]rAtRS
OR STEPS.
THE UNIT
f4UST F_ELIFTED, OR PUSHED
UP A RAMP,
Attacl; tb.,Phand!P, tothe cornpresso_ saddle by inserting
the har;,ite :aside the compressor
sadd!e aRd Iin!ng up
the L_o!th,:.%;_: I:_-_ e ,_:_c h side. insialfthet..:_.oscrews,
or_eori
each sid,}, Tif]_ht_:nsecurely.
it will be necessary
to brace
or support
one side of the outfit
when
installing
the
wheels
because
the compressor
will have
a tendency
to .tip o_er.
_: "_'"-
,_,1 .... s are
: _:.,,,_l sec_ _rely.fhe outfit wiil sit level ifth?,
_,;
properly installed.
,::ie_r i,_r;d d_/unde=s;C_:: o fa;r tan k leg opposite whee!s.
i_-_ _ove the F;ot,_-_:i_ve..m-ip[rc;m the adhesive backed
m:;.i,J_cdfoot bL'm.:',:_m. A.tt_a,.th the _oot bL!m_'ers tothe
bc!::om of leq ,3r;ear.l_ e;_,J. Hr:esu flrr_ ,y :=_ko r qace.
INSTALLAT ON
AND BREAK-IN
PROCEDURES
Location
of the Air Compressor
__ocate t¢iLsi;
C'C,,
f,_r_:_sso, i n a c,_arL c;_ / a'ld wel! ventilated
area. The ak coh:pre:;sor should be i_..'.ated at ;east ! 2" away
from the Wall or o[her obstructions
that wiil interfere with the
........ ,_ L t,:._.0ot _ LJRipa_!,_., b; iro_d ai e,Je_lgFied
t,_- a !!_w for prop<._r.'..'::'oi !rig. Th 3 ve,.'-.ti!a[ic.'nopen ,rigs on t:]e
,;Oral.:r,._sse_' _o :-;_-_c_ssa,-,, to mair-_13]__ b."oper operating _ern-
r,_;ra_ure. E',>iq,:;Lpb,,e rq0s c:r O_b£;copt-_iR,_-s c;n or r,ear
theseop.er_;:_{;_.
Lubrication and Oil
If an ex_er_sion cord mJ_t _._ L =ed, be sure iI is:
a %w'.re extensioq
cord tl;at has a .:,-,.,i._ci8g, o,.,_=d=ag
pl.; ._., a. _da 3 =Ict r.:,,.,_,........= t!}_t w_!l._.ccept the plug o[]
the p_oduct
,i ......
:',
;,o Ir_.nger thar_ 50 f_et:
-
t2 gauge (AWG) or _a_'ger. _,Wire size increases
as
gauge number decreases.
10 AWG and 8 AWG may
a_.o be used.
DO NOT USE t 4 OR 16 AWG.)
This unit needs no lubrication
or oiling.
Voltage
and Circuit
Protection
Extension Cords
Use extra air hose instead of an extension cord to avoid voltage
drop and power !oss to the motor, and to prevent overheating.
Refer to your Parts List Manual for the voltage and circuit
protection
requirements
of your compressor.
Use only a
fuse or circuit breaker that is the same rating asthe branch
circuit the air compressor
is operated
on. If the compressor
is connected
to
a circuit protected
by fuses, use only dual element
time
delay fuses, as noted in that Service Bulletin.
Advertisement
