HP StorageWorks XP10000 - Disk Array Configuration Manual page 14

1. Show all wwids.
P00>wwidmgr -show wwid
[0] UDID:176 WWID:01000010:6006-0e80-0350-6200-0009-0010-5062-00b0 (ev:none)
[1] UDID:177 WWID:01000010:6006-0e80-0350-6200-0009-0010-5062-00b1 (ev:none)
[2] UDID:178 WWID:01000010:6006-0e80-0350-6200-0009-0010-5062-00b2 (ev:none)
[3] UDID:179 WWID:01000010:6006-0e80-0350-6200-0009-0010-5062-00b3 (ev:none)
[4] UDID:180 WWID:01000010:6006-0e80-0350-6200-0009-0010-5062-00b4 (ev:none)
[5] UDID:181 WWID:01000010:6006-0e80-0350-6200-0009-0010-5062-00b5 (ev:none)
[6] UDID:182 WWID:01000010:6006-0e80-0350-6200-0009-0010-5062-00b6 (ev:none)
[7] UDID:183 WWID:01000010:6006-0e80-0350-6200-0009-0010-5062-00b7 (ev:none)
[8] UDID:184 WWID:01000010:6006-0e80-0350-6200-0009-0010-5062-00b8 (ev:none)
[9] UDID:185 WWID:01000010:6006-0e80-0350-6200-0009-0010-5062-00b9 (ev:none)
[10] UDID:186 WWID:01000010:6006-0e80-0350-6200-0009-0010-5062-00ba (ev:none)
2. Set the disk you installed the boot file system on:
P00>wwidmgr -quickset -item 2 -unit 1
3. Check the disk assignment and reachability.
P00>wwidmgr -show reach
Disk assignment and reachability after next initialization:
6006-0e80-0350-6200-0009-0010-5062-00b2
via adapter:
dga1.1001.0.4.1
dgb1.1001.0.3.0
4.
Initialize the system.
P00>init
5. Show devices.
P00>show dev d
dga1.1001.0.4.1
dgb1.1001.0.3.0
dka0.0.0.2004.0
dka500.5.0.2004.0
dqa0.0.0.15.0
dva0.0.0.1000.0
The list of adapters is displayed, showing fabric topology.
6. Set the Boot default device.
P00>set bootdef_dev dga1.1001.0.4.1,dgb1.1001.0.3.0
7. Boot the system.
P00>boot
14 Installing and configuring Tru64 for the XP disk array
via fc nport:
pga0.0.0.4.1
pgb0.0.0.3.0
$1$DGA1
$1$DGA1
DKA0
DKA500
DQA0
DVA0
connected:
5006-0e80-0350-6211
5006-0e80-0350-6211
HP OPEN-V
HP OPEN-V
COMPAQ BF01863644
COMPAQ BF01863644
Compaq CRD-8402B
Yes
Yes
2114
2114
3B05
3B05
1.03