Craftsman 113.207650 Owner's Manual page 2

FULL ONE YEAR WARRANTY ON CRAFTSMAN SCROLL SAW
If within one year from the date of purchase, this Craftsman Scroll Saw fails due to a defect
in material or workmanship, Sears will repair it, free of charge+
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS
SERVICE CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES
This warranty applies only while this product is in use in the United States
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state
SEARS, ROEBUCK AND CO+, 698/731A, Sears Tower, Chicago, IL 60684
general safety instructions for power tooms
1+ KNOW YOUR POWER TOOL
Read and understand the owner's manual and labels
affixed to the tool Learn its application and limitations
as welf as the specific potential hazards peculiar to this
tool+
2,, GROUND ALL TOOLS
This tool is equipped with an approved 3-conductor
cord and a 3+prong grounding type plug to fit the pro+
per grounding type receptacle. Tile green conductor in
the cord is the grounding wire, Never connect the
green wire to a live terminal.
3+ KEEP GUARDS IN PLACE
- in working order, and in proper adjustment and
alignment.
4+ REMOVE ADJUSTING KEYS AND WRENCHES
Form a habit of,checking to see that keys and adjusting
wrenches are removed from tool before turning it on.
5. KEEP WORK AREA CLEAN
Cluttered areas and benches invite accidents Floor
must not be slippery due to wax or sawdust.
+
7+
+
94
10+
11+
12+
13+
14+
15_
sistant lenses, they are NOT safety glasses." Also, use
face or dust mask if cutting operation is dusty, and ear
protectors (plugs or muffs) during extended periods of
operation+
SECURE WORK
Use clamps or a vise to hold work when practical tt's
safer than using your hands and frees both hands to
operate tool
DON'T OVERREACH
Keep proper footing and balance at all times+
MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for best and safest per-
formance. Follow instructions for lubricating and
changing accessories+
16. DISCONNECT TOOLS
before servicing; when changing accessories such as
blades, bits, cutters, etc
17+ AVOID ACCIDENTAL STARTING
Make sure switch is in"OFF" position before plugging
in power cord,,
AVOID DANGEROUS ENVIRONMENT 18. USE RECOMMENDED ACCESSORIES
Don't use power tools in damp or wet locations or ex-
Consult the owner's manual for recommended acces+
pose them to rain_ Keep work area well lighted. Pro-
vide adequate surrounding work space+
KEEP CHILDREN AWAY
All visitors should be kept a safe distance from work
alea+
MAKE WORKSHOP KID+PROOF
-- with padlocks, master switches, or by removing
starter keys
DON'T FORCE TOOL
It will do the job better and safer at the rate for which
it was designed+
USE RIGHT TOOL
Don't force tool or attachment to do a job it was not
designed for,
WEAR PROPER APPAREL
Do not wear loose clothing, gloves, neckties or jewelry
(rings, wristwatches) to get caught in moving parts+
NONSLtP footwear is recommended, Wear protective
hair covering to contain tong hair, Roll long sleeves
above the elbow..
USE SAFETY GOGGLES (Head Protection)
Wear safety goggles (must comply with ANSi Z87+1)
at all times "Everyday eyeglasses only have impact re+
sories+ FoIIow the instructions that accompany the ac-
cessories The use of improper accessoriesmay cause
hazards,
19. NEVER STAND ON TOOL
Serious injury could occur if the tool is tipped or if the
cutting tool is accidentally contacted,,
Do not store materials above or near the tool such that
it is necessary to stand on the tool to reach them.
20_ CHECK DAMAGED PARTS
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to ensure
that it will operate properly and perform its intended
function+ Check for alignment of moving parts, binding
of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard
or other part that is damaged should be properly re-
paired or replaced.
21. DIRECTION OF FEED
Feed work into a blade or cutter against the direction
of rotation of the blade or cutter only_
22+ NEVER LEAVE TOOL RUNNING UNATTENDED
Turn power off. Don't leave tool until it comes to a
complete stop+