Tamper Proof Function; Setting The Clock; Automatic Clock Setting - Sharp 13VT-CR10 Operation Manual

Tamper Proof Function

POWER
POWER button
1
4
7
FLASHBACK
REW
REC
TIMER
ON/OFF
CONFIRM
RETURN button
TV • VCR COMBINATION

Setting The Clock

1 AUTOMATIC CLOCK SETTING

• To set the clock automatically, follow the procedure below:
(1) Press the MENU button on
the Remote Control.
Press the +/– button to
move " :" mark
"CLOCK", then press the
SET button.
(2) The "CLOCK SET" screen
will be displayed. Press
the +/– button to select
"AUTO CLOCK ON" and
press the SET button.
(3) The " :" mark will move
to "EDS CH AUTO". If the
EDS channel in your area
is known, use the +/–
button to select the
channel. Otherwise, select
"AUTO". Press the SET
button.
(3.1) Turn off the power.
The clock is set
automatically using EDS
signals while the power is
off.
• If the EDS channel is
selected, it takes only a
few minutes for the clock
to set.
12
12-15 13VT-CR10[E].pm65e
INPUT DISPLAY MUTE
VOL
2 3
5 6
•
CH
8 9 CHANNEL
e
•
•
UP/DOWN
TR
•
•
0 100
d buttons
COUNTER TAPE TAMPER
RESET SPEED PROOF
TAMPER
PROOF
PLAY
button
FF
STOP
PAUSE/STILL
d DPSS e
– +
PROG
RETURN SET MENU
MENU button
SET button
M E N U
T I M E R
V I D E O A D J U S T
C L O S E D C A P T I O N
to F U N C T I O N
C L O C K
L A N G U A G E
C H S E T T I N G
S E L E C T + / — : S E T S E T
P R E V I O U S R E T U R N : Q U I T M E N U
C L O C K S E T
A U T O C L O C K O N
E D S C H A U T O
M O N T H - - -
D A Y - -
Y E A R - - - -
T I M E - - : - - - -
S E L E C T + / — : S E T S E T
P R E V I O U S R E T U R N : Q U I T M E N U
C L O C K S E T
A U T O C L O C K O N
E D S C H A U T O
M O N T H - - -
D A Y - -
Y E A R - - - -
T I M E - - : - - - -
S E L E C T + / — : S E T S E T
P R E V I O U S R E T U R N : Q U I T M E N U
T H E C L O C K I S
A U T O M A T I C A L L Y S E T W H E N
T H E U N I T I S T U R N E D O F F .
12
L Operation Mode Lock
• If the TAMPER PROOF Lock is on during operation of this
product, the current operation mode will not change until
the TAMPER PROOF Lock is released, even if another
operation button is pressed.
L Power-Off Mode Lock
• If the TAMPER PROOF button is pressed to engage the
TAMPER PROOF Lock while the POWER button is set to
off, the power cannot be turned on even if the POWER
button is pressed.
Example: Engaging the Tamper Proof Lock during playback.
1 Press and hold down the TAMPER PROOF button on the
Remote Control for about 3 seconds. The "
PROOF" indicator on the front panel of this product will
flash, and then remain lit to indicate that the lock is
engaged.
2 Regardless of any operation buttons pressed, the current
operation mode will not change.
The TAMPER PROOF Lock can be disengaged by the
following method:
• Press the TAMPER PROOF button on the Remote Control
for about 3 seconds. The "
on the front panel of this product will flash, and then go
out to indicate that the lock is disengaged.
• If "AUTO" is selected for
clock setting, it may take
a few hours to complete
the clock setting as your
TV has to search for the
EDS channel.
(If you want to use the
clock functions immedi-
ately, proceed to step (2)
for MANUAL CLOCK SET-
TING. Please refer to page
13.)
(3.2) Press the power on.
Once the Auto Clock
setting is completed, the
time is displayed on the
bottom right corner of the
TV screen.
Note:
• If you move to other location, try to preset the channels
again (See page 10 for presetting the channels) and set
the clock again following the procedure above.
• If the Auto Clock setting is still not completed even a few
hours after turning off the power, EDS signals may not be
broadcast in your area. In this case, set the clock manually.
(See page 13 for manual clock setting.)
• If the antenna signal is weak, the AUTO CLOCK SETTING
function may not operate.
• The AUTO CLOCK SET will not function if there is no EDS
signal broadcast.
• Select a channel that carries EDS signals with the e or d
button.
15/5/01, 7:53 pm
TAMPER
TAMPER PROOF" indicator
2
A I R
1 0 : 2 0 A M O C T . 1 5