Related Manuals for Scytek electronic Vectra X5
Summary of Contents for Scytek electronic Vectra X5
- Page 1 VECTRA X5 SERIES VEHICLE SECURITY SYSTEM WITH REMOTE START W W I T H S E P E R A A T E L O C K / U N L O C K B U T T O N S PRODUCT MANUAL...
- Page 2 Limited Lifetime Warranty This vehicle security system is warranted to the original purchaser, to be free from defects in material and workmanship. The manufacturer will repair or replace at its option, and free of charge for the first twelve (12) months, any part that proves defective in material or workmanship under normal installation, use, and service, provided the product is returned to the manufacturer freight prepaid.
-
Page 3: Table Of Contents
Table of Contents About Your System ............Page 1 Remote Transmitters . -
Page 5: About Your System
About Your System The ScyTek VECTRA X5 Series is a Combination Vehicle Security and Remote Starting System featuring a built-in "ScyNet Network Port" that allows direct connection of optional accessory modules and a PC interface offering expanded system operation. With proper installation this system will provide superior protection and performance for many years to come. -
Page 6: Remote Transmitters
Remote Transmitters Standard Remote Transmitter Description Button 2 Button 1 Button 5 Button 3 Button 4 Depending on the model chosen, the VECTRA X5 Series will be supplied with one or two T5 or T5-SP 5- button Remote Transmitters that are used to control the system’s operations. Note: Using the optional PC or Pocket PC interface with the network software, it is possible to reconfigure the functionality of the transmitter buttons. -
Page 7: Remote Transmitter Description
Adding/Replacing Standard Remote Transmitters To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired transmitters ready and follow the steps below. Note: Up to 4 one-way transmitters can be programmed to operate the system. Any previously stored transmitter will be erased if it is not programed within the following sequence To program the transmitter(s): 1. -
Page 8: 2-Way Lcd Remote Transmitter Description
2-way LCD Remote Transmitter Description Button 1 Button 2 Button 3 Button 4 Button 5 Depending on the model chosen, the VECTRA X5-2W Series will be supplied with one or two 2-way LCD Remote Transmitters, offering increased range and confirmation of any activated features. Page 1 Button 1 Arms and Locks the system and when held for 5 seconds, activates the system’s Panic feature. -
Page 9: Lcd Transmitter Battery Replacement
3. Press and release Button 1 on the first transmitter then on the second transmitter. · The siren/horn will chirp/honk once for every transmitter learned. 4. Turn off the ignition key. 5. The siren/horn will chirp/honk 3 times to indicate the system has exited programming mode. LCD Transmitter Battery Replacement Your Galaxy Remote Transmitter uses a 1.5 volt AAA alkaline battery, which will require replacement in time. -
Page 10: System Confirmation
To set the daily start feature: 1. Press and hold Buttons 2 and 3 until the remote beeps four times. · The fan and clock will be shown indicating daily start mode is entered. 2. Press Button 2 until the desired hour is displayed. 3. - Page 11 CHP Set the siren/horn confirmation chirps/honks ON or OFF: 1. Press and hold Button 5 until the display shows CHP. ·The transmitter will beep three times. 2. Release Button 5. · The transmitter will beep once. · The LCD panel will show a siren if the chirps*/honks are enabled or "off" if the chirps*/honks are disabled.
- Page 12 Page 8 - VECTRA X5...
-
Page 13: System Operation
System Operation Remote Arming/Locking The system monitors 5 independent areas ( zones ) while armed: doors, hood/ trunk, shock sensor, optional sensor input, and the network port for future expansion. To Arm and Lock the System: 1. Turn off the ignition. 2. -
Page 14: Tamper Alert
Tamper Alert If the system was triggered while away, the LED will flash to indicate which zone triggered the system after disarming and turning the ignition ON. The LED indication will repeat 8 times. LED Flashes (60 seconds): 1 flash optional sensor 2 flashes shock sensor... -
Page 15: Panic Mode
Panic Mode In the event of an emergency, the transmitter’s remote Panic feature can be used to instantly trigger the alarm/panic feature. To activate the Panic Mode: 1. Press and hold Button 1 for five seconds. · The alarm will sound. ·... -
Page 16: Automatic Rearming
3. Press the valet switch 4 times. · The siren will chirp each time the valet switch is pressed. 4. Within 5 seconds, press Button 3 on the transmitter. · The siren will chirp 3 times. 5. Press the valet switch the number of times equal to the desired code (from 1-15). 6. -
Page 17: Remote Start Features
Remote Start Features Remote Starting To Remote Start the System: 1. Be sure the system is not in Valet Mode. 2. Press and hold Button 4 for three seconds. · The parking lights will flash 4 times and turn on. ·... -
Page 18: Automatic Start Mode
Automatic Start Mode Automatic Start feature has three modes that will start the vehicle every one or two hours within a 24 hour period. 1. Timer Only Mode (factory default) The Automatic Start feature starts the vehicle automatically every one or two hours and runs for the preset Run Time. -
Page 19: Manual Transmission Remote Starting
Manual Transmission Remote Start Features Model: VECTRA X5-M 1- Tach wire must be connected , The system must learn RPM. 2- Hand brake must be connected. 3- Door trigger must be connected 4- Clutch override installed NOTE: MUST USE RELAY, SEE PAGE 26. Remote Starting With engine running and Hand-brake engaged put the vehicle transmission in neutral and remove the foot from the brake pedal, press the remote start button on your transmitter, parking lights will flash twice... -
Page 20: Extended Features
Extended Features Ignition Door Locking For added safety, the Ignition Door Locking feature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on. If a door is open when the ignition is turned on, the Ignition Door Locking feature is disabled to protect against locking the keys inside the vehicle. -
Page 21: System Installation
System Installation 1. Thoroughly read and become familiar with the installation instructions before beginning the installation. 2. Review system contents: Main Unit 1 or 2 One-way 5 Button Remote Transmitters (varies by model) 1 or 2 Two-way 5 Button LCD Remote Transmitters (varies by model) Siren Shock Sensor Harnesses... -
Page 22: Mounting The Control Unit
Mounting the Control Unit The control unit must only be mounted in the interior of the vehicle. Do not mount the main unit in the engine compartment. Choose a mounting location that will not be easily accessible to a thief, and will not interfere with the operation of any vehicle components such as foot pedals, steering column, air vents, seat rails, etc. -
Page 23: System Wiring
System Wiring 6-Pin Starter Harness Pin 1 RED WIRE A: Main Power Input A (+). Connect to the battery or constant power wire at the ignition switch with a minimum 25 Amp supply. Remove the fuse until the installation is complete and all wiring is checked. -
Page 24: Plug-In Connectors
Pin 11 VIOLET WIRE: Positive Door Input (+). Connect to the door switch circuit wire that shows +12V when the door is open. This type of door circuit is usually found on Ford vehicles. Pin 12 GREEN WIRE: Negative Door Input (-). Connect to the door switch circuit wire that shows ground when the door is open. -
Page 25: Jumper Settings
2-Pin White Connector: Located on the side of the main module. · Green WIRE - Parking Brake Input (-) For Manual Transmission and/or vehicles equipped with a turbo charged engine. Must be connected if using the Turbo Timer feature and/or Manual Transmission remote start feature. ·... -
Page 26: System Programming
System Programming Entering System Programming This system is compatible with both the LCD two way transmitter or the standard transmitter, all system programming can be performed using either one. To enter System Programming: 1. Turn the ignition switch to the ON position. 2. - Page 27 Programming Branch Table Branch Feature Button 1 (default) Button 2 Button 3 1. Arm Mode Manual Arming Passive Arming 2. Auto Rearming Mode Disabled Enabled 3. Arming Chirps Siren Chirps On Siren & Horn Chirps On Silent 4. Ignition Door Locking Set Override Code 5.
- Page 28 10. Ignore Open Door Report. Bypasses the open zone warning chirps for vehicles equipped with a residual dome light circuit that remains on for a period of time after closing the door. 11. Aux 2 Auto Activate with Arm. When selected, the Auxiliary 2 output will activate when the system is armed.
- Page 29 Tach Monitor mode: monitors the vehicle’s tach wire (or a fuel injection wire) in real-time to determine engine status and adjust starter crank time automatically. Gas Engine. Sets the engine type for Gasoline. Diesel Engine. Sets the engine type for Diesel and monitors the glow plug input to make sure the glow plugs are warm before cranking the starter.
-
Page 30: Relay Diagrams
Relay Diagrams Positive Dome Light Activation Negative Dome Light Activation Positive Horn Honk Negative Horn Honk Starter Defeat/Anti-Grind Negative Glow Plug Page 26 -VECTRA X5... -
Page 31: Door Lock Diagrams
Door Lock Diagrams Follow the diagrams below for connecting basic door lock systems. For Two Stage door lock systems (separately unlocks driver and passenger doors) see following pages. Negative Trigger Positive Trigger blue green Reverse Polarity Vacuum Adding Actuators VECTRA X5 - Page 27... -
Page 32: Two Stage Door Lock Diagrams
Two Stage Door Lock Diagrams The VECTRA X5 Series is equipped with a dedicated Passenger Unlock output allowing Two Stage Door Lock operation. When connected as shown below, disarming the system will unlock only the driver’s door. Pressing the disarm button again will unlock all doors. Two Stage Negative Trigger Two Stage Positive Trigger Door Lock Inverter Green Wire... - Page 33 Two Stage Door Lock Diagrams cont’d Two Stage Reverse Polarity Two Stage Adding Actuators VECTRA X5 - Page 29...
-
Page 34: Technical Information
Technical Information FCC ID: OARRXAM2000 This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation Built-in LED Light/Override/Valet/Call Switch into Antenna... -
Page 35: System Diagnostics
Starter Diagnostics Starter doesn’t start and parking lights flash: 3 Times - Engine RPM not detected (check tach wire and/or perform tach learn procedure) Hood Trigger is active (hood is open, wire is shorted to ground or pin switch is defective) 4 Times - Brake Trigger is active ( Brake switch input is shorted to ground or incorrect) 5 Times - Unit is in Valet (service) mode, and start is disabled. -
Page 36: Wiring Diagram
Wiring Diagram VECTRA X5 Series Green Lock output (-) 500mA Blue Unlock output (-) 500mA Shock Sensor Port Green/White Brake Input(+) Black/Gray Tachometer Input White/Red Auxiliary 2 Output (-)500mA LED Port Black/White Dome Light output (-)500mA (must use relay) Valet Switch Port Yellow Ignition Input (+) ( Must Be connected Blue/Yellow...
Need help?
Do you have a question about the Vectra X5 and is the answer not in the manual?
Questions and answers