Related Manuals for Scytek electronic Astra 200
Summary of Contents for Scytek electronic Astra 200
- Page 1 ASTRA 200 W W I I T T H H S S E E P P E E R R A A T T E E L L O O C C K K / / U U N N L L O O C C K K B B U U T T T T O O N N S S PLUG AND PLAY 2-W W AY UPGRADE VEHICLE SECURITY SYSTEM PRODUCT MANUAL...
- Page 2 Limited Lifetime Warranty This vehicle security system is warranted to the original purchaser, to be free from defects in material and workmanship. The manufacturer will repair or replace at its option, and free of charge for the first twelve (12) months, any part that proves defective in material or workmanship under normal installation, use, and service, provided the product is returned to the manufacturer freight prepaid.
-
Page 3: Table Of Contents
Table of Contents About Your System ............Page 1 2-way LCD Remote Transmitters . -
Page 5: About Your System
About Your System Congratulations on your purchase of this state-of-the-art vehicle security system from ScyTek Electronics. With proper installation this system will provide superior protection and performance for many years to come. System Contents: Main Unit • Two 5-Button Random Code Remote Transmitter •... -
Page 6: Way Lcd Remote Transmitters
Optional 2-way LCD Remote Transmitter Description Button 1 Button 2 Button 3 Button 4 Button 5 The Astra’s 200 Optional 2-way LCD remote transmitter is offering increased range and confirmation of any activated feature. Page 1 Button 1 Arms and Locks* the system and when held for 5 seconds, activates the system’s Panic feature. Button 1 also locks the doors when the system is in Valet Mode. -
Page 7: Adding/Replacing 2-Way Lcd Transmitters
Adding/Replacing 2-way LCD Transmitters (2 LCD remotes maximum) When adding an optional 2-way LCD transmitter to the system, follow these steps: 1. Turn on the ignition key On, Off, On, Off, On, Off, and back On. (Key On 4 times) ·... -
Page 8: Lcd Backlight
LCD Backlight Transmitter Button 5 is used for confirmation, transmitter programming, as well as activation of the LCD backlighting for use in the dark. Press button 5 to activate the LCD backlight. System Confirmation The 2-way transmitter's confirmation feature allows the current vehicle status to be displayed at any time. -
Page 9: Lcd Icon Description
VLT Valet mode function sets and resets the security system valet mode. * this function is enabled only when the security system is disarmed Set or reset the Valet mode: 1. Press and hold Button 6 until the display shows VLT. ·... -
Page 10: Remote Transmitters
Remote Transmitters Remote Transmitter Description Button 1 Button 2 Button 5 Button 3 Button 4 The Astra 200 is supplied with Two 5-button Remote Transmitter used to control system operations. Button 1 Arms and Locks* the system and when held for 5 seconds, activates the system’s Panic feature. -
Page 11: Adding/Replacing Transmitters
Adding/Replacing One-Way Transmitters To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired transmitters ready and follow the steps below. Note: Up to 4 one-way transmitters can be programmed to operate the system. Any previously stored transmitter code will be erased if it is not programed within the following sequence. -
Page 12: System Operation
System Operation Remote Arming The system monitors 4 independent areas ( zones ) while armed: doors, hood/trunk, shock sensor and optional sensor input. To Arm the System: 1. Turn off the ignition. 2. Press Button 1. · The siren will chirp once.* ·... -
Page 13: Tamper Alert
Tamper Alert If the system was triggered while away, the LED will flash to indicate which zone triggered the system after disarming and turning on the ignition. The LED indication will repeat 8 times. LED Flashes: 1 flash optional sensor 2 flashes shock sensor 3 flashes... -
Page 14: Panic Mode
Panic Mode In the event of an emergency, the transmitter’s remote Panic feature can be used to instantly trigger the alarm. To activate the Panic Mode: 1. Press and hold Button 1 for 5 seconds. · The alarm will sound. ·... -
Page 15: Automatic Rearming
6. Turn off the ignition then arm the system. 7. Disarm the system using the new Override Code to permanently store the new code. Note: If the code set procedure is not properly performed, turn off the ignition and begin again. The override code will not be permanently stored until the code is used to disarm the system. -
Page 16: Extended Features
Extended Features Ignition Controlled Door Locks For added safety, the Ignition Door Locking feature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on, and unlock the doors after the ignition key is turned off. If a door is open when the ignition is turned on, the ignition locking feature is disabled to protect against locking the keys inside the vehicle. -
Page 17: System Installation
System Installation 1. Thoroughly read and become familiar with the installation instructions before beginning the installation. 2. Review system contents: Main Unit 2 One-Way 5-Button Remote Transmitter Siren Shock Sensor Harnesses Reciever Antenna 14-Pin main harness • 4-Pin shock sensor harness •... -
Page 18: Mounting The Control Unit
Mounting the Control Unit The control unit must only be mounted in the interior of the vehicle. Do not mount the main unit in the engine compartment. Choose a mounting location that will not be easily accessible to a thief, and will not interfere with the operation of any vehicle components such as foot pedals, steering column, air vents, seat rails, etc. -
Page 19: System Wiring
System Wiring 14-Pin Main Harness Pin 1 RED WIRE: +12V Battery Input (15A Fuse). The RED wire must be connected to a clean source of continuous +12V power. Pin 2 WHITE WIRE: Parking Light Output (+/-) relay. Connect the White wire to the circuit that shows +12V or ground only when the parking lights are on and set the internal parking light relay jumper to the proper polarity. -
Page 20: Plug-In Connectors
Plug-in Connectors 3-Pin White Door Lock Connector: Plug-in connector port for door lock harness or optional door lock relay module. · BLUE WIRE - negative unlock output (-) 500mA. · GREEN WIRE - negative lock output (-) 500mA. 2-Pin Red Connector: Plug-in connector port for LED. Mount the LED in an area where it may be easily seen from either side of the vehicle. -
Page 21: System Programming
System Programming Entering System Programming To enter System Programming: 1. Turn on ignition. 2. Within 5 seconds, press the valet switch 5 times. · The siren will provide three chirps, indicating that you have entered Programming. 3. Press the valet switch the number times equal to the System Option you want to change. ·... - Page 22 6. Ignore Open Door Report. Bypasses the open zone warning chirps for vehicles equipped with a residual dome light circuit that remains ON for a period of time after closing the door. 7. Auto Rearming Mode. When selected, the system will automatically re-arm and lock 30 seconds after it has been disarmed regardless if a door is open or closed.
-
Page 23: Branch Table
21. Smart Siren Mode. When Enabled works with Optional ScyTek MP3 Player Siren Unit. Branch Feature Button 1 (default) Button 2 Button 3 1. Horn Chirps w/ Arm&Disarm Normal Horn Chirps 2. Arm Mode Manual Arming Passive Arming 3. Passive Door Locking Disabled Enabled 4. -
Page 24: Door Lock Diagrams
Door Lock Diagrams Follow the diagrams below for connecting basic door lock systems. For Two Stage door lock systems (separately unlocks driver and passenger doors) see following pages. Negative Trigger Positive Trigger Reverse Polarity Vacuum Adding Actuators Page 20 - Astra 200... -
Page 25: Two Stage Door Lock Diagrams
Two Stage Door Lock Diagrams The Astra 200 is equipped with a dedicated Passenger Unlock output allowing Two Stage Door Lock operation. When connected as shown below, disarming the system will unlock only the driver’s door. Pressing the disarm button again will unlock all doors. Two Stage Negative Trigger Two Stage Positive Trigger From Inverter or Relay... - Page 26 Two Stage Door Lock Diagrams cont’d Two Stage Reverse Polarity Two Stage Adding Actuators Page 22 - Astra 200...
-
Page 27: Technical Information
Technical Information FCC ID: OARRXAM2000 This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation LED light Valet/Call/Override... -
Page 28: Wiring Diagram
Wiring Diagram ScyTek Electronics 11627 Cantara Street North Hollywood, CA 91605 www.scytek.net © ScyTek Electronics 2006 Astra 200 12-11-06...