Advertisement
SCYTEK ELECTRONICS
ASTRA 50
REMOTE KEYLESS ENTRY SYSTEM
INSTALLATION & OPERATING INSTRUCTIONS
INTRODUCTION:
CONGRATULATIONS on your choice of a Remote Keyless Entry System by ScyTek Electronics Inc.
This booklet contains the information necessary for installing, and operating your system. If any questions
arise, contact your installation dealer or ScyTek Electronics Inc. at the Tech Support number below.
*IMPORTANT INFORMATION: Primary and Optional Features
-PRIMARY FEATURES: These are features that must be connected in order for the system to operate
properly i. e. Power & Ground, along with the Primary features of Power Locks & Flashing Lights.
OPTIONAL FEATURES: Optional features are connected only if desired or agreed upon by the installing
dealer i. e. Driver's Separate Unlock, Horn Chirp, Dome light illumination, Trunk Pop, etc. These features
may require additional parts and labor charges. Consult with your installer and come to an agreement
about your optional features before installation. NOTE: The LED is required for programmable options.
See page 8.
This device complies with FCC Rules part 15. Operation is subject to the following two conditions: 1) This
device may not cause interference, and (2) this device must accept any interference that may be
received, including interference that may cause undesired operation. The manufacturer is not responsible
for any radio or TV interference caused by unauthorized modification to this equipment. Such modification
could void the user's authority to operate the equipment.
TECH SUPPORT
Mon- Fri 8: 00 AM- 4: 30 PM Pacific Time
(800) 693-7505
www.scytek.net
email: scytek@scytek.net
Advertisement
Table of Contents
Related Manuals for Scytek electronic Astra 50
Summary of Contents for Scytek electronic Astra 50
- Page 1 SCYTEK ELECTRONICS ASTRA 50 REMOTE KEYLESS ENTRY SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION: CONGRATULATIONS on your choice of a Remote Keyless Entry System by ScyTek Electronics Inc. This booklet contains the information necessary for installing, and operating your system. If any questions arise, contact your installation dealer or ScyTek Electronics Inc.
-
Page 2: Pre-Installation Considerations
PRE- INSTALLATION CONSIDERATIONS To ease installation, we suggest that you READ THIS MANUAL before beginning your installation. BEFORE BEGINNING , check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS BRAKES, ENGINE / BODY COMPUTER AND BATTERY). PLAN OUT YOUR INSTALLATION and determine most suitable locations for all components to be placed. -
Page 3: Power Door Lock Wiring
Connect to dome light activation circuit for Negative type circuits. For Positive type circuits, open the control module and move the jumper the plug as shown in illustration. The DEFAULT is NEGATIVE. BLUE/ WHITE WIRE: (-) PASSENGER( S) DOOR UNLOCK OUTPUT (Optional, requires relay) Connects to unlock circuit for passenger door( s) when using separate driver’s door unlock option. - Page 5 SEPARATE DRIVER’S DOOR UNLOCK DIAGRAMS...
-
Page 8: Option Programming
TRANSMITTER PROGRAMMING Turn Ignition ON and OFF 3 times quickly, leaving it ON the time. (ON/OFF, ON/OFF, ON) 2. Lights should flash 3 times & horn will chirp 3 times if horn feature is installed. 3. Push and hold the Program/Override Button for about 5 seconds until you get 3 lights/LED flashes & 3 Horn chirps. -
Page 9: Operation
This option modifies the unit’s (-) Negative Armed Starter Disable output operation. When this option is turned ON, the unit will PASSIVELY activate the Starter Disable 45 seconds after the ignition is turned off. Starter disable output is deactivated through the remote when unlocking the vehicle or a manual override. 6. - Page 10 VALET MODE To get in and out of VALET mode, turn the ignition on and press the override/program button for about 7-8 seconds. When going into VALET you will get (1) horn chirp, (1) light flash, and LED will be on SOLID. When coming out of VALET mode you will get (2) Chirps, (2) Flashes, and LED will go out.