Advertisement
ON CRAFTSMAN
WOOD:SHAPER
this
Craftsman:
Wood
Shaper
fails
duel to
a defect
in material
or
AVAILABLE
BY
SIMPLY
CONTACTING
THE
NEAREST
SEARS
STORE
OR SERVICE
_her rights which vary from state to state,
Sears Tower.
Chicago,
IL 60684
general
safety
-,
:i
•
:
r
Instructions
fo
power
tools
1. KNOW YOUR
POWER TOOL
Read
and
understand
the
owner's
manual
and labels
affixed
to
the
toot.
Learn
its
application
and
limitations
as
wel!
as the
specific
potential
hazards
peculiar
to this too!,
2. GROUND
ALL TOOLS
This
tool
is equipped
w_th
an approved
3-conductor
Cord
and
a 3-prong
grounding
type
plug
to
fit
the
proper
grounding
type receptacle.
The green conductor
in the cord
is the grounding
wire.
Never connect
the
green wire to a live terminal.
3. KEEP GUARDS
tN PLACE
in working
order,
and
in
proper
adjustment
and
alignment,
4, REMOVE
ADJUSTING
KEYS
AND WRENCHES
Form
habit
of checking
to see that
keys and adjusting
wrenches
are removed
from
tool
before
turning
it on.
5. KEEP WORK AREA
CLEAN
Cluttered
areas
and
benches
inwte
accidents.
Floor
must notbe
slippery
due to wax
or sawdust.
6.:AVOID
DANGEROUS
ENVIRONMENT
Don't-use
power:tools
in
damp
or wet
locations
or
expose
them
tO Cain.
Keepw0(k'
area
we
lighted.
Provide
adequate
surrounding
work
space.
7, KEEP CHtLDREN
AWAY
All
vis=tors
sho_J|d be
kept-a
safedistance
from
work
area.
8. MAKE WORKSHOP
KID-PROOF
with
padlocks,
master
switches,
or
by
removing
starter
keys.
9. DON'T
FORCE TOOL
It will
do the job better
and safer at the rate for which
tt was desMgned
10. USE RIGHT
TOOL
Don't
force
tool
or attachmem
to do a job
_t was not
designed
for.
11. WEAR PROPER APPAREL
DO not wear
loose clothing,
gloves,
neckties
or jewelry
(rings,
wrist
watches)
to get caught
in moving
parts.
Nonsfip
footwear
is recommended.
Wear
protective
hair covering
to contain
long
hair.
Roll
long sleeves
above the el bow.
12. USE SAFETY
GOGGLES
(Head Protection)
Wear Safety
goggles (must
comply
with
ANSi
Z87.1)
-at all times.:
Everyday
eyeglasses
0nly
have
impact
resistant
_lenSes, ;they: are NOT-safety
glasses.,Also,
use
face or dust
mask if cutting
operation
is dusty,
and ear
protectors
(plugs
or muffs)
during
extended
periods
of
operation,
13. SECURE WORK
Use clamps or a vise to hold work
when
practical,
It's
safer than using your
hand,
frees both
hands to operate
tool
14. DON'T OVERREACH
Keep proper
footing
and balance
at all times.
15. MAINTAIN
TOOLS WITH CARE
Keep
tools
sharp
and
clean
for
best
and
safest
performance.
Follow
instructions
for
lubricating
and
changing
accessories.
16. DISCONNECT
TOOLS
before
servicing;
when
changing
accessories
such
as
blades,
bits, cutters,
etc.
17. AVOID
ACCIDENTAL
STARTING
Make sure switch
is in "OFF"
position
before
plugging
in,
18. USE RECOMMENDED
ACCESSORIES
Consult
the
owner's
manual
for
recommended
_accessories,
Follow
the
instructions
that
accompany
i::,!!: i :i;_:!:,i:::!::tfi_:'accessories.
The use of
improper
accessories
mav
hazards,
STAND
ON TOOL
....
Serious
injury
could
occur
if the tool is tipped
or if the
:
cutting
tool
is accidentally
contacted.
Do not
store materials
above or near the toot such that
it _snecessary
to stand on the tool to reach them.
20. CHECK DAMAGED
PARTS
Before
further
use of the tool,
a guard or other
part that
is damaged
should
be carefully
checked
to ensure that it
will operate
properly
and perform
_ts intended
function.
Check for
alignment
of moving
parts, binding
of mowng
parts,
breakage
of
parts,
mounting,
and
any
other
conditions
that
may .affect
its
operation.
A guard
or
other
part
that
is damaged
should
be properly
repaired
or replaced.
21. DIRECTION
OF FEED
Feed work
into
a blade or cutter
against
the direction
of rotation
of the blade or cutter
only,
22. NEVER
LEAVE
TOOL
RUNNING
UNATTENDED
Turn
power
off.
Don't
leave tool
until
it comes
to a
complete
stop.
Advertisement
