Advertisement
2; :ELEVATING
CONTROL
LEVER
, i ....
1 !, STARTING
PIN
The :,Elevating
::i:co_troi
Lever: : movesl _he: spindle
: :The Starting' Pin must be used as a pivot to support the
:vertically :a di_ait_:of,718:inch
to locate:the: cUttei;_;at:
: i:iwork unti!:it
has been fed into the cutter and against
the desired:vertical_i_Sition_
the collar. The Starting
Pin may be located in either of
the two threaded holes near the table insert opening,
depending
upon
the
direction
of
rotation,
but
determined,
ALWAYS
on the in-feed side.
CAUTION:
Always release the quill lock knob before
12. REMOVING
AND INSTALLING
CUTTERS
attempting
to ichattge ithe iposition:of
Spindle
a.
Raise:spind}e to maximum height
tighten the knob Secureiy before startinff operation. : ....
b.
To REMOVE cutter, hold spindle with the 1/4" hex
4. SPINDLE
L_ .This::= shaper is designed for use with
wrench and loosen nut with wrench provided
as
maximum
2Li/2-inch
diameter
cutters having
a l/2:inch
diameter
bore.
5_ SPACERS-
A total
of three
spacers are provided,
two
7/16inch
thick
and one
1/4 inch think
for positioning
the cutter
for desired
shapes.
6;
KEYED
WASHER
-
Must
always
be
positioned
immediately
below
the spindle nut;
7.
FENCE
ADJUSTING
KNOB
Each fence face may be
moved
forward
or
backward
by
turning
the
fence
adjusting
knobs.
8.
FENCE
LOCK
KNOB
-
After
the desired
fence
face
position
has
been
selected,
the
fence
is secured
bY
tightening
the fence lock knobs.
9.
FENCE
FACES
--
Each fence
may be moved
forward
or
backward
by
releasing
the
fence
lock
knob
and
turning
the
fence
adjusting
knobs.
Each
fence
face
operates
independently
of the other,
by means of the
adjusting
mechanism.
After
the desired
fence
position
has been selected,
it is secured
by tightening
the fence
lock
knob.
The
fence
faces
wilt
close
in
from
a
maximum
three-inch
opening
down
to
one-inch
for
Small diameter
cutters,
by loosening
the two
screws in
the front
of each face and sliding
the face to the desired
posiiton.
The Screws must
be tightened
securely
after
each setting.
CAUTION;
The opening between inner ends of fence faces
ShOuld: never _be large_ than required
to just clear the
particular cutter being
used. ALWAYS
ROTATE
THE
SPINDLE BY HAND BEFORE
STARTING
THE SHAPER
MOTOR TO MAKE SURE CUTTER
DOES NOT STRIKE
FENCE FACES,
10. CUTTER GUARD
NOTE:
Used for curved or irregular
shaping only -
fence must be removed and starting
pin must
be in
place on in-feed side.
Provides added protection for irregular shaping. Guard
is adjustable for various thickness of material.
CAUTION;
Always rotate the spindle by hand before
starting the shaper motor to make sure cutter does not
strike guard,
shown-
Reverse procedure to TIGHTEN
SPINDLE
NUT.
NOTE:
TO
AVOID
POSSIBLE
BENDING
OF THE
SPINDLE
LOOSEN OR TIGHTEN
NUT WITH
BOTH
WRENCHES
POINTING
AS NEARLY
IN THE SAME
DIRECTION
AS POSSIBLE.
CAUTION:
Always
have the keyed washer directly
under the nut, otherwise the nut may loosen and
serious injury could resu|t.
/
WRONG
RIGHI"
•
•-•::::i:: • •: •• •:• O••::• •• :• •:
• :__-•i _•:•i: • :• •
:'14. ¸
Advertisement
