Maintenance; Pump Oil Maintenance; Checking And Cleaning Inlet Screen; Checking High Pressure Hose - Craftsman 580.752870 Operator's Manual

OWNER'SRESPONSiBiLiTiES
Follow the hourly or calendar intervals, whichever occurs
first. More frequent service is required when operating in
adverse conditions noted below.
ii ii _ i iiii iiii ]i i;;iiii_ii_i{ii_i!_i!i}iiiii}} iiiiJii }iiiii_ i{_ _ii _!Ji}iiii_i_i} _ii iiH_iiiii i i]iiii iiii iiiiii iiii iiiiii iiii iiiiii iiii iiiiii iiii iiiiii iiii iiiiii iiii iiiiii iiii iiH HH HH H HH H_
• Changeengine oil
iiiiiiiiii,'_ iiiiiiiiii;1; ; ;; ;;; ;; 3
• Check/clean water inlet screen'
• Check high pressure hose
• Check detergent siphoning hose
• Check spray gun and assembly for leaks
• Cleandebris
• Check engine oil level
!i{i;;iiiiiiiiiiii_iiiiiiiiiiiiiiiii ]i/i;;i i i iiii _} iii ii_ i{i iiiiiii i HH:::::__i_ii
• Cleanengine air cleaner_
• Changeengine oil_
• inspect muffler and spark arrester
• Replaceengine air cleaner_
• Replacespark plug
• Cleancooling system_
Clean if clogged. Replace if perforated or torn.
2 Service more often under dirty or dusty conditions.
GeneralRecommendations
Regular maintenance will improve the performance and
extend the life of the pressure washer. See any Sears or
other qualified service dealer for service.
The pressure washer warranty does not cover items that
have been subjected to operator abuse or negligence. To
receive full value from the warranty, the operator must
maintain pressure washer as instructed in this manual
including proper storage as detailed in Storage.
Some adjustments will need to be made periodically to
properly maintain your pressure washer.
All service and adjustments should be made at least once
each season. Follow the requirements in the Maintenance
Schedule chart above.
NOTICE Oncea year you should clean or replace the spark
plug and replace the air filter. A new spark plug and clean air
filter assure proper fuel-air mixture and help your engine run
better and last longer.
Pump Oil
DO NOT attempt any oil maintenance on this pump. The
pump is pre-iubricated and sealedfrom the factory, requiring
no additional maintenancefor the life of the pump.
EmissionsControl
Maintenance, replacement, or repair of the emissions
control devices and systemsmay be performedby any non-
road engine repair establishment or individual. However,
to obtain "no charge" emissions control service, the work
must be performed by a factory authorized dealer. Seethe
Emissions Warranty.
BeforeEachUse
1. Checkengine oil level.
2. Cleandebris.
3. Checkwater inlet screen for damage.
4. Checkhigh pressure hose for leaks.
5. Checkgun and nozzle extension assembly for leaks.
6. Purge pump of air and contaminants.
PRESSURE W ASHER MAINTENANCE
Clean Debris
Daily or before use, clean accumulated debris from pressure
washer. Keeplinkage, spring and controls clean. Keep area
around and behind muffler free from any combustible debris.
inspect cooling air slots and openings on the pressure
washer. These openings must be kept clean and
unobstructed.
Pressure washer parts should be kept clean to reduce the
risk of overheating and ignition of accumulated debris.
• Use a damp cloth to wipe exterior surfaces clean.
NOTICE improper treatment of pressure washer could
damage it and shorten its life.
• DONOTinsertanyobjectsthroughcoolingslots.
• Use a soft bristle brush to loosen caked on dirt, oil, etc.
• Use a vacuum cleaner to pick up loose dirt and debris.
Checkand Clean Iniel Screen
Examinegarden hose inlet screen. Cleanif it is clogged or
replace if it is torn.
CheckHigh Pressure Hose
High pressure hoses can develop leaks from wear, kinking,
or abuse, inspect hose before each use. Check for cuts,
leaks, abrasions, bulging of cover, or damage or movement
of couplings. If any of these conditions exist, replace hose
immediately.
_i_ WARNING The high pressure stream of water that
this equipment produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
, NEVER repairhigh pressure hose.Replace it.
• Replacement hoseratingMUSTequalor exceed maximum
pressure ratingof unit.
18