Advertisement
(_
Press
the
Mode
button
MODE
While
holding
the
Mode,
press
the Override button
O
forlOsecond,stoenter
OWtRIDE
Setup _c_ens
iMPORTANT:
Be sure
to press
and hold the override
bulon
with the Mode button
for ful ten seconds.
/2:DD_=
_)
Adjust
the time
of day
)
clock.
TJ#:T_ c_r_g_ hours quickly press arid
hdd 1,,_ov,'tt_d,_ _ottot, rt, and pto_s
the up or Oown buttons
NOTF
Fach
step
number
_s located
at
the top
lght
corner
of the
dls/ay
for easy _derence
/
Select
the day
of the
week.
Select
display
operation,
Full Display (On) el
Minimal
display
(Off),
ON
Display
Off
Select
Fan
operalon,
Far
Of_,
o_ Fan
Auto,
or
Fa_
Off
on
_
eleCt Heat Pump, O_ or O1.
OFF
off
NOTE: Step 5 is not applicable for use with Duct-Free Split Heat Pump
Systems.
Adjust
the
deadband
_
from
1 to 6 degrees
F.
C"
(1 to6F)
Adjustthe
minimum
between
cooling
and
heating
_
set_nls.
(07o
6F)
Select
the cycles
per
t_:A=_t
hou_llmlt.
_
d=cycles
per hour
limit defeated.
Comp_essorlocko_t.
(d, dl,2-6}
(_
Select the display back-
_
_
light always Oar or Off
ON
?7 o,;"°'"°°°"
&
STEP NO.
1
2
3
4
5
6
7
8
9
10
Advanced Setup Table
DESCRIPTION
RANGE
FACTORY
DEFAULT
Time of day clock set
24 hour
12:00 Am
Day of the week
Su - Sa
Mo
Display Blanking
Off / On
On
Fan Operation
Auto / On
Auto
Heat Pump*
Off / On
On
Deadband
or Temperature
swing
1 - 6 F
2 F
Forced minimum difference
7eat/cool
0 - 6 F
2 F
Sycles per hour
d, dl, 2 - 6
6
]-hermoglow
TM
backlight
Off / On
On
Fahrenheit
or Celsius
F / C
F
*Not applicable for use with Duct-Free Split Heat Pump systems.
• CLOCK BACKUP -- In the event of a power loss,
the thermostat internal clock will continue to keep
proper time for a minimum of 48 hours without
external power or batteries.
• MINIMUM HEAT/COOL SETPOINT DIFFERENCE
-- The Heat and Cool set points will not be allowed
to come any closer to each other than the value set
in Advanced Setup Step 6, on this page. This mini-
mum difference is enforced during Auto changeover
and Program On operation.
• ENERGY SAVING SMART FAN -- If a manual fan
speed is selected, the fan will run continuously at all
times. If mode is Off, the fan will only run if there is a
heating or cooling demand in Unoccupied periods.
• OVERRIDE -- As explained on page 2, pressing
the Override button during a programmed,
Unoccu-
pied period will force the thermostat into Occupied
1, temporarily, for up to 4 hours. If the Override but-
ton is pressed during an Occupied period, the ther-
mostat will be forced into Unoccupied and the
occupied period (1,2 or 3), it was forced out of will
be turned off, only for that day.
During Override periods the set points may be
adjusted, but they will not be remembered after
Override ends.
• KEYPAD LOCK--
To prevent unauthorised use of
the thermostat, the front panel buttons may be dis-
abled. To disable or 'lock' the keypad, press and
hold the Mode button. While holding the Mode but-
ton, simultaneously
press the Up and Down but-
tons. The Locked icon will appear on the display.
•
] k i
irl
:i
I
Press all 3 for
_
.... ,_,_<=
Lo_d
=e pa°Loc,out\
c
_ E_
Select
thermostat
ope_alon
in degrees
F
Press
the Mode button. While holding
the Mode, press
the Override
button to
eave the Setup
screens,
If no buttons
are pressed,
the display
will leave the
_etup screens after 60 seconds,
To unlockthe
buttons, again press and hold the
Mode button. While holding the Mode button, simul-
taneously press the Up and Down buttons. Locked
will disappear from the display.
DISPLAY BLANKING -- The thermostat display
may be configured in advanced setup, this page,
Step 3, to always be visible as normally expected,
or may be selected Off. When selected Off, only the
time of day will appear until a button is pressed.
When a button is pressed the full, normal display
will appear and then revert to the time of day only,
after roughly 10 seconds.
Page 4
Advertisement
