Advertisement
•
Donot handle charger o r Hand Vac
with wet hands.
•
Hand Vac is for dry pick up only.
•
Do not put any objects in ventilation openings. Do not
use with any opening blocked: keep openings free of
dust, lint, hair, and anything that may reduce air flow.
•
NEVER vacuum materials such as hot coals, cigarette
butts, matches, etc.
•
Do not use without filter in place.
•
Turn off all controls before unplugging from or
plugging into an electrical outlet for charging.
•
Use extra care when using on stairs.
•
Do not use to pick up hard objects such as nails,
screws, coins, etc. Damage or injury could result.
•
Hand Vac does not have to be plugged into an electri-
cal outlet, therefore it is always in operating condition.
Be aware of possible hazards when using your Hand
Vac or when changing accessories.
•
USE ONLY THE CHARGER PROVIDED WITH YOUR
HAND VAC. Do not substitute any other charger. Use
of another charger could cause batteries to explode
causing possible serious injury.
•
DO NOT PLACE HAND VAC OR BATTERIES NEAR
FIRE OR HEAT. They may explode.
•
Your Hand vac should be charged in a location where
the temperature is more than 50°F but less than 100°F.
•
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in contact
with skin, wash at least 10 minutes then seek immedi-
ate medical attention.
Know your power tool. Read operator's manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to
this tool. Following this rule will reduce the risk of
electric shock, fire, or serious injury.
•
Always wear safety glasses. Everyday eyeglasses
have only impact-resistant
lenses; they are NOT
safety glasses. Following this rule will reduce the risk
of serious personal injury.
•
Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
WARNING: ELECTRIC SHOCK COULD OCCUR IF
CHARGED OUTDOORS OR ON WET SURFACES.
Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should
be carefully checked to determine that it will
operate properly and perform its intended func-
tion. Check for alignment of moving parts, binding
of moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation.
A guard or other part that is damaged should be
properly repaired or replaced by an authorized
service center. Following this rule will reduce the risk
of shock, fire, or serious injury.
Make sure your extension cord Is in good condi-
tion. When using an extension cord, be sure to use
one heavy enough to carry the current your prod-
uct will draw. A wire gage size (A.W.G.) of at least
16 is recommended
for an extension cord 100 feet
or less in length. A cord exceeding 100 feet is not
recommended.
If in doubt, use the next heavier
gage. The smaller the gage number, the heavier
the cord. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
•
Drugs, alcohol, medication. Do not operate tool
while under the influence of drugs, alcohol, or any
medication. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
•
Save these instructions. Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them
these instructions also.
SERVICE
•
Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel could result in a risk of injury.
•
When servicing a tool, use only identical replace-
ment parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of shock or injury.
A
WARNING:
Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and
other masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
SAVE THESE INSTRUCTIONS
4
Advertisement
