Turning An Effect Module On And Off; Storing And Copying A Patch - Zoom 2100 Operation Manual

Turning an effect module on and off

STORE
In Edit mode, use the parameter select key
to select the module to turn on and off.
Press the [ON/OFF] key.
The corresponding module is turned on or off.
• Instead of the parameter select keys, you can use foot
NOTE
switches 1–3 or the [BANK ] switch to turn the effect
module on and off.

Storing and copying a patch

When you select another patch, the edited patch is reset to its pre-edited status, unless you store
the patch into memory. If you have created a favorite patch, be sure to store it. You can also make
a copy of an existing patch by storing it in a different location. If you copy the patches for the same
song into the same bank, it is much easier and quicker to switch between the patches during
performance.
Press the [STORE] key in Play mode or Edit
mode.
The 2100 enters store standby mode.
Use the [BANK ] switch and foot switches
1–3 to select a copy destination patch.
If you do not specify the destination, the original
bank number and the patch number will be
automatically selected.
You cannot store the patch in the PRESET group. If a
NOTE
patch from the PRESET group is selected before you
perform step , pressing the [STORE] key will
automatically select patch "01" of the USER group. Select
the desired bank number and patch number.
POSITION1.COMP/WAH•DIST
BANK PATCH
2.DIST•COMP/WAH
COMP / WAH DIST EQ MOD REV / DLY
Type(RTM) Type Treble Type Type
Sens / Rate Gain / Top Middle Depth /Time Time
POSITION Tone / Body Bass Rate /Pit/FB Tone /FB
BOTH PRESET
Patch Level Level ZNR Mix /Mode Mix
GROUP(EXIT)
Master Level Gain Trim Presence Amp Sim Rev Trim
1 2 3 B
JAM 1 JAM 2 JAM 3 JAM REC
JAM PLAY
MONITOR
POSITION1.COMP/WAH•DIST
BANK PATCH
2.DIST•COMP/WAH
COMP / WAH DIST EQ MOD
Type(RTM) Type Treble Type
Sens Rate Gain Top Middle Depth
/ / /Time
POSITION Tone / Body Bass Rate /Pit/FB
BOTH PRESET
Patch Level Level ZNR Mix /Mode
STORE GROUP(EXIT)
Master Level Gain Trim Presence Amp Sim
1 2 3
JAM 1 JAM 2 JAM 3
JAM PLAY
MONITOR
SAMPLER COMP / WAH DIST MOD REV/ DLY
1.AUX Mix 2.AUX Lch
1.COMP 1.CLEAN 1.CHORUS 1.HALL
3.AUX Rch 4.PLAYNOTE
2.PEDAL-WAH 2.OVER DRIVE 2.STEREO CHO 2.ROOM
3.AUTO-WAH 3.DISTORTION 3.FLANGER 3.PP-DELAY 1
Max Rec Time
4.TREMOLO 4.FUZZ / GRUNGE 4.PHASE 4.PP-DELAY 2
5.RING MOD 5.LEAD 5.PITCH
Constant Pitch
6.SLOW ATTACK 6.METAL 6.PEDAL-PITCH
7.ACOUSTIC 7.DELAY
Tone
UTILITY
FUNCTION +
ON / OFF
BANK
VALUE
SAMPLER
–
PARM
REC
FUNCTION
SPEED
• In step you can also press and hold the parameter
NOTE
select key for more than one second to turn the selected
module on and off. The parameter select key of the
SAMPLER module, however, is a special key used to
enter Sampler mode, and cannot be used to turn other
modules on and off.
The module on/off setting is stored as part of the
HINT
HINT
corresponding patch.
REV / DLY SAMPLER COMP / WAH DIST MOD REV/ DLY
1.AUX Mix 2.AUX Lch
1.COMP 1.CLEAN 1.CHORUS 1.HALL
Type
3.AUX Rch 4.PLAYNOTE
2.PEDAL-WAH 2.OVER DRIVE 2.STEREO CHO 2.ROOM
3.AUTO-WAH 3.DISTORTION 3.FLANGER 3.PP-DELAY 1
Time Max Rec Time
4.TREMOLO 4.FUZZ / GRUNGE 4.PHASE 4.PP-DELAY 2
5.RING MOD 5.LEAD 5.PITCH
Tone /FB Constant Pitch
6.SLOW ATTACK 6.METAL 6.PEDAL-PITCH
7.ACOUSTIC 7.DELAY
Mix Tone
UTILITY
Rev Trim FUNCTION +
ON / OFF
BANK
B
VALUE
JAM REC
– SAMPLER
PARM
REC
FUNCTION
SPEED
Press the [STORE] key again to store (copy)
the patch. If you wish to cancel the store
operation, press the [GROUP/EXIT] key
instead.
The patch is stored and the 2100 returns to Play
mode.
• When you execute the store (copy) operation, the patch
NOTE
in the destination will be erased and cannot be
recovered. You can, however, revert any patch or all
patches in the USER group to their factory default
settings. (See page 20.)
• You can also use the [VALUE+/–] keys to select the
copy (store) destination.
11