Modifying Tonal Color Of Patches (Using Edit Mode); Modifying The Parameter Settings - Zoom 2100 Operation Manual

Modifying tonal color of patches
In Edit mode, you can modify the effect parameters in the patches and the patch parameters to create the desired patches,
and change the settings of the global parameters. This section describes the operation in Edit mode.

Modifying the parameter settings

Select a patch to edit in Play mode (in either
the USER group or the PRESET group).
Press and immediately release the
parameter select key that corresponds to
the module you wish to edit.
The 2100 enters Edit mode, in which you can
change the parameter settings.
The information shown below appears on the
panel in Edit mode.
Press the parameter select key repeatedly
to select a parameter to edit.
To select a parameter in the module, press the
same parameter select key repeatedly. The
parameter LEDs will flash in sequence.
The global parameters are listed on the bottom of the
NOTE
parameter list printed on the front panel. Use the
[UTILITY] key to select a global parameter.
[Panel indication in Edit mode]
BANK PATCH
BOTH PRESET
Parameter value
The value of the
currently-selected
JAM PLAY
parameter appears
MONITOR
on the display.
When the module is
turned off, " "
appears.
10
POSITION1.COMP/WAH•DIST
BANK PATCH
2.DIST•COMP/WAH
COMP / WAH DIST EQ MOD REV
Type(RTM) Type Treble Type
Sens / Rate Gain / Top Middle Depth /Time
POSITION Tone / Body Bass Rate /Pit/FB
BOTH PRESET
Patch Level Level ZNR Mix /Mode
STORE GROUP(EXIT)
Master Level Gain Trim Presence Amp Sim
1 2 3 B
JAM 1 JAM 2 JAM 3 JAM REC
JAM PLAY
MONITOR
POSITION1.COMP/WAH•DIST
2.DIST•COMP/WAH
COMP WAH DIST EQ
/
Type(RTM) Type Treble
Sens / Rate Gain / Top Middle Middle Depth
POSITION Tone / Body Bass Rate
Patch Level Level ZNR Mix
Master Level Gain Trim Presence Amp Sim
1 2
JAM 1 JAM 2
Turning the effect module on and off
If the effect module has been turned on for the currently-selected
patch, the corresponding module LED lights up.
/ DLY SAMPLER COMP / WAH DIST MOD REV/ DLY
1.AUX Mix 2.AUX Lch
1.COMP 1.CLEAN 1.CHORUS 1.HALL
Type
3.AUX Rch 4.PLAYNOTE
2.PEDAL-WAH 2.OVER DRIVE 2.STEREO CHO 2.ROOM
3.AUTO-WAH 3.DISTORTION 3.FLANGER 3.PP-DELAY 1
Time Max Rec Time
4.TREMOLO 4.FUZZ / GRUNGE 4.PHASE 4.PP-DELAY 2
5.RING MOD 5.LEAD 5.PITCH
Tone /FB Constant Pitch
6.SLOW ATTACK 6.METAL 6.PEDAL-PITCH
7.ACOUSTIC 7.DELAY
Mix Tone
UTILITY
Rev Trim FUNCTION +
ON / OFF
BANK
VALUE
– SAMPLER
PARM
REC
FUNCTION
SPEED
Use the [VALUE+/–] key to modify the value.
Pressing the [VALUE +] key once increments the
value by one, and pressing the [VALUE –] key
once decrements the value by one. Pressing and
holding down one of these keys and pressing the
other key will change the value rapidly.
Repeat steps – above to edit the other
parameters.
When you finish editing, press the
[GROUP/EXIT] key.
The 2100 returns to Play mode.
This parameter modification is temporary. All parameters
NOTE
will be reset to their original values when you select
another patch in Play mode, unless you store the
currently-selected patch. (The global parameters will be
reset when the power is turned off.) See page 11 for
information on storing patches.
Middle Parameter for edit
The intersection of the
horizontal line from a
MOD REV DLY SAMPLER
/
flashing module LED and
1.AUX Mix 2.AUX Lch
Type Type
3.AUX Rch 4.PLAYNOTE
a vertical line from a
/Time Time Max Rec Time
flashing parameter LED
/Pit/FB Tone /FB Constant Pitch
indicates the parameter
currently selected for
/Mode Mix Tone
editing.
Rev Trim FUNCTION
If the selected module
3 B
has been turned off, the
JAM 3 JAM REC
module LED flashes at
different intervals.
(Using Edit mode)