Page 1
Operators Manual Model Series 140 thru E173 Single Stage Snow Throwers Model 150 shown IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning: This unit is equipped with an inlernal combustion engine and should not be u_ed on or near any unimproved forest- covered, brush-covered or grass-covered...
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF OTHERS. READ FOLLOW INSTRUCTIONS THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR SNOW THROWER. FAILURE TO COMPLY WITH THESE...
• If the snow thrower should start to vibrate abnormally, Never direct discharge at bystanders or allow anyone in front of unit. stop the engine and check immediately for the cause. Vibration is generat)y a warnin Oof trouble. Disengage power collector/impeller when •...
SECTION 2: FINDING YOUR MODEL NUMBER This Operator's Manual is an important part of your new snow thrower, it will help you assemble, prepare and maintain your snow thrower. Please read and understand what it says. Before you start to prepare your snow thrower for its first use, please locate the model plate and copy the information from it in this Operators Manual.
SECTION 4: UNPACKING INSTRUCTIONS • See Figure 3. • Remove staples, break glue on the top flaps of the carton or cut tape at carton end and peel along top flap to open carton. Remove any loose parts included with unit (i.e., Operator's manual, etc.). •...
Page 6
RAISING THE UPPER HANDLE Loosen the hand knob on each side of the handle. Bee Figure 4. Remove packing material (if any). Squeeze the control handle against the upper handle. Hold it in this position as you raise the handle. Pull the handle up into the operating position.
Page 7
INSTALLING CHUTE CRANK (Models with Optional Extended Chute Crank only.) On some units, the chute crank can be installed and secured from the top side of the snow thrower. Other units are equipped with an adaptor that requires the assembler to tip the unit forward on the auger housing in order to secure the crank from the underside.
Page 8
SECURE FROM THE UNDERSIDE. See Figure 8. Place a piece of the cardboard from the carton on a level sudace, Tip the snow thrower forward so that the housing rests on the cardboard from the box. Thread one 5/16" hex nut all the way onto the eyebolt. Slide the eyebolt onto the chute crank.
FUEL AND OIL MIXTURE tank indoors, when engine is running or while engine is still hot. Do not smoke when filling fuel WARNING: Handle gasoline carefully. Remember that It Is highly flammable. Never fill fuel tank. Your snow thrower uses a two cycle engine that requires a mixture of gasoline and two cycle engine oil. Refer to the Engine Operator's Manual for proper Oil and Fuel Recommendations.
SNOW THROWER OPERATING CONTROLS Model 140 Model 140 (w/ Optional Ext. Models 150,151 Models 142,152 Chute Crank) 172,173 AJger AJger Control Auger Control Handle Control _'4andle Handle _Crank Chut Chute Figure 11 Auger Control Handle - Located on the upper handle, the auger control handle is used to engage and disengage the augers.
SECTION 7: OPERATION Warning' Observe all warning labels on the snow thrower prior to use. See Section 1. FUEL MIXTURE Important: Mix oil with gasoline as instructed in the Oil and Fuel Recommendations Section in the separate Engine Operator's Manual packed with your snow thrower. Read and follow all instructions carefully. BEFORE STARTING ENGINE...
SECTION 8: ADJUSTMENTS running, WARNING: NEVER attempt to clean chute or make any adjustments or repairs while engine is SHAVE PLATE ADJUSTMENT Augers Shave Plate Wheels Nuts & Bolts Figure 13 To check the adjustment of the shave plate, place the unit on a level surface. See Figure 13. The wheels, shave plate and augers should all contact the level surface.
SECTION 9: MAINTENANCE is running, WARNING: NEVER attempt to clean chute or make any adjustments or repairs while engine NOTE: Check engine and snow thrower frequently for loose nuts, bolts, etc., and keep these items tightened, ENGINE Refer to the separate Engine Operator's Manual packed with your snow thrower for all engine maintenance procedures.
SECTION 10: OFF-SEASON STORAGE WARNING: Never store engine with fuel in tank indoors or in enclosed, poorly ventilated areas where fuel fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer, or other gas appliance. •...
Page 15
Models E150 E151 REF. PART i QTY. DESCRIPTION _:-1 710-1270 :Screw--Ova! C-Sink L 710-0487 Bolt Carriage 712-0324 NUt Insl. Lock 720-0276 Knob--Handle Tie Cable 725-0157 _746-0883 Body--Lever Control 1747-0946 Handle Ass'y. Control i749-0705 Handle--Upper 1736-0451 Washer Saddle Models E 152 E172 E173 PART...
Page 21
Models 140, E142 Tightening Torque: 150-130 in. Ibs. "-FIEF. PART PART QTY. QTY. DESCRIPTION DESCRIPTION 7i0-0157 --| Screw--Hex 751-0535-12 Hose--Fuel 12" 710-0805 /Screw--Hex 754-0367 V-Belt 756-0416B V-Pulley Half !710-0896 IScrew--Washer 756-0550 Pulley 1726-0205 jClamp--Hose !736-0242 Washer--Bell 1784-5177 Engine Support Bracket 750-0589 Spacer Obtain from Engine...
Page 22
Mode1150 Tightening Torque; lS0-300 in. Ibs. REF.T PART "QTY. i DESCRIPTION DESCRIPTION 705-5139 Bracket - Supped Gas Tank 741-0475 Bushing - PJastic ..751-0535-16 Hose- Fuel Line 16" 710-0157 Screw - Hex Cap 751-0540A Tank- Fuel 2 Qt. 710-0289 Screw - Hex 710-0896 Screw - Washer 78t-0800...
Page 23
Models E150, E151, E152, E172, E173 Tightening Torque: 150-300 in. Ibs. REF. PART I REE PART DESCRIPTION DESCRIPTION QTY. 629:0z36 Cord - Extension 110V3M Washer - Bell 736-0242 736-0329 2 Prong Washer- Lock 705-5139 741-0475 _oTv. i .o. Bracket - Support Fuel Tank Bushing - Plastic 710-0157 751-0535-16...
Page 24
MANUFACTURER'S LIMITED WARRANTY FOR: YA.. c,,N s)[( For TWO YEARS from the date of retail purchase products sold or exported outside of the United States of America, its possessions and territories, within the United States of America, its possessions and territories, MTD PRODUCTS INC will, at its except those solcl through MTD PRODUCTS...