Related Manuals for Yard Machines 317E660G000
Summary of Contents for Yard Machines 317E660G000
- Page 1 OUTDOOR POWER EQUIPMENT Model Numbers 24", 26" and 28" 317E610E000 SNOW 317E640F000 THROWERS 317E660G000 MTD PRODUCTS INC • P.O. BOX 368022 • CLEVELAND, OHIO 44136-9722 PRINTED IN U.S.A. FORM NO. 770-8782M...
-
Page 2: Safe Operation Practices
IMPORTANT SAFEOPERATION PRACTICES THIS SYMBOL POINTS OUT IMPORTANT SAFETYI1_ STRUCTIONSWHICH, IF NOT FOLLOWED,COULD ENDANGERTHE PERSONAL_ SAFETYAND/OR PROPERTY OF YOURSELF AND CTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTINGTO OPERATE YOUR SNOW THROWER•FAILURETO COMPLYWITH THESEINSTRUCTIONSMAY RESULTIN PERSONAL, INJURY.WHENYOUSEE THIS SYMBOL-- _IL HEEDITS WARNING. DANGER: any type of power equipmer t, carelessnessor error on the part of the operatorcan result in seriousinjury, if Yoursnow throwerwas bull to be operated accordingto the rules for safe operation in this manual. - Page 3 CONTENTS OF HARDWARE PACK Lay out the hardware according to the illustration for identification purposes. Parts are illustrated approximately one-half size. Part numbers are shown in parentheses. (Hardware pack may contain extra items which are not used on your unit.) ATTACHING THE HANDLE ASSEMBLY S I ATTACHING THE CHUTE ASSEMBLY .exoo,,.
-
Page 4: Tools Required For Assembly
ASSEMI3LY INSTRUCTIONS UNPACKING IMPORTANT: This unit is shipped WITHOU'" GASO- 1. Remove staples or break glue on the top flaps of LINE or OIL. After assembly, see separab_ engine the carton. Remove any loose parts included with manual for proper fuel and engine oil rec:_mmen- unit (i.e., owner's manual, etc.). - Page 5 ATTACHING THE CHUTE ASSEMBLY (Hardware B) Chute Assembly 1. Grease the chute opening using a multi-purpose Hex Head automotive grease or equivalent. Screw Place chute assembly over chute opening, with the opening in the chute assembly facing the front Flat Washer of the unit.
- Page 6 IMPORTANT: Attachthe shift rod andcl itch cables as follows. THEN CHECK THE ADJUSTMENTS INSTRUCTED, AND MAKE ANY FINAL A[)JUSTMENTS NECESSARY BEFORE OPERATING YOUR SNOW THROWER. Failure to follow the instructi,)ns may cause damage to the snow thrower. ATTACHINGTHE SHIFT ROD (Hardware D) 1.
-
Page 7: Shift Lever
If necessary, loosenthe hexjam nut andthreadthe shoes in the low position. Use middle or high position cablein (forlessslack)or out(formoreslack)as nec- when area to be cleared is uneven. See figure 9. essary.Referto figure8. Recheck the adjustment. Adjust skid shoes by loosening the four hex nuts and Tightenthe jam nut againstthe cablewhencorrect carriage bolts and moving skid shoes to desired posi- adjustment is reached. -
Page 8: Fuel Shut Off Valve
SAFETYIGNITIONSWITCH(see figure12) AUGER DRIVE (See figure 10) The auger drive clutch is located on the let handle. The ignition key must be inserted in the switch before Squeeze the clutch grip to engage augers. the unit will start. Remove the ignition key when snow thrower is not in use. -
Page 9: To Stop Engine
4. Move throttle control up to FAST position. Insert Electric Starter: Connect power cord to switch box on ignition key into slot. See figure 12. Be certain it engine, then to 120 volt AC receptacle. With the snaps into place. Do not turn key. engine running, push starter button and spin the starter for several seconds. -
Page 10: Operating Tips
SKIDSHOEADJUSTMENT TIRECHAINS(OptionalEquipment) Tire chains should be used whenever extra t'action is The space between the shave plate and the ground needed. can be adjusted. Refer to page 7 of the Assembly Instructions. OPERATING TIPS TRACTION DRIVE CLUTCH ADJUSTMENT NOTE: Allow the engine to warm up for a fev, minutes Refer to the Final Adjustment section of the Assembly as the engine will not develop... - Page 11 CARBURETORADJUSTMENT WHEELS Oil or spray lubricant into wheel bearings at least once a season. Remove wheels, clean and coat axles with a the engine while the engine is running WARNING: If any adjustments are made to multi-purpose automotive grease. See figure 16. (e.g.
-
Page 12: Belt Removal And Replacement
DRIVEAND SHIFTINGMECHANISM To remove shave plate, remove the carriage bolts, belleville washers and hex nuts which attach it to the At least once a season or after every 25 h(urs snow thrower housing. Reassemble new shave plate, operation, remove rear cover. Lubricate any gears, making sure heads of the carriage bolts are to the... -
Page 13: Drive Belt
Drive Belt Rear Friction Auger Englne Wheel lulley Front Auger Belt Support Engine Bracket Pulley Rear Frame Auger Pulley Idler Belt Pulley FIGURE 19. Auger Pulley Idler Pulley Auger Bracket Spring Houslng Spring FIGURE 20. 6. Unhook the idler spring from the hex bolt on the auger housing. - Page 14 If unit is to be stored over 30 days, prepare for storage 3. Remove six self-tapping screwsfromthe frame coverunderneath t hesnow thrower. as follows: 4. Remove the klickpinswhichsecurethe v'heels, 1. Remove all gasoline from carburetor and fuel tank andremove thewheels fromtheaxle. to prevent gum deposits from forming on these parts and causing possible malfunction of engine.
-
Page 15: Troubleshooting Guide
TROUBLE SHOOTING GUIDE Trouble Corrective Action Possible Cause(s) Engine fails to start 1. Fuel tank empty, or stale fuel. 1. Fill tank with clean, fresh gasoline. 2. Fuel shut-off valve closed. 2. Open shut-off valve. 3. Key not in switch on engine. 3. - Page 16 _hoe Plate...
- Page 17 _ories or Service Information, 800-8001731 0 Model Number Serial Number 00000000000 00000000000 Product Number 00000000000 not fill all the above spaces lhe only way to ensure the performance of your product is to use original equipment parts and .]ccessories. MTD designs and engineers quality parts to exacting...
Need help?
Do you have a question about the 317E660G000 and is the answer not in the manual?
Questions and answers