Craftsman 351.286281 Operator's Manual page 2

Warranty .................................. 2
Safety Rules .............................. 2-3
Unpacking ................................. 3
Assembly ................................. 3
Installation ............................... 4-5
Operetlon ................................ 5-9
Maintenance ............................ 9-10
Troubleshooting ............................ 11
Parts Illustration and List .................. 13-15
FULL TWO YEAR WARRANTY ON
CRAFTSMAN 6'I." JOINTER/PLANER
If within two full years from the date of purcllese, this
Craftsman Jolnterlplener falls due to a defect in matedsl
or workmanship, Sears w_LI r epair it free of charge.
Warranty service is available by contacting Sears. This
warranty is in addition to any statutory warranty.
If this Jolnter/planer is used for commercial purposes,
this warranty applies for only g0 days from t_a date of
purchase.
Sears Canada, thc., Toronto, Ontario MSB 2B8
WARNING: For your own safety, read all of the rules
and precautions before operating tool.
CAUTION:
Always follow proper operating procedures
as defined in this manual even if you are familiar with
use of this or similar tools. Remember that being care-
less for even a fraction of a second can result In severe
personal injury.
BE PREPARED FOR JOB
• Wear proper apparel. Do not wear loose clothing,
gloves, necldles, rings, braceletS or other Jeweify
which may get caught In moving parts of machine.
• Wear protective hair covering to contain long hair.
• Wear safety shoes with non-slip soles.
• Wear safety glasses complying with United States
ANSI Z87.1. Everyday glasses have only impact
resistant lenses. They are NOT safety glasses.
• Wear face mask or dust mask if operation is dusty.
• Be alert and think clearly. Never operate power tools
when tired, intoxicated or when taking medications
that cause drowsiness.
PREPARE WORK AREA FOR JOB
• Keep work area clean, Clutteredwork areas invite
accidents.
• Do not use powertools]n dangerousenvironments.
• Do not use power tools in damp or wet locations. Do
not expose power tools to rein.
• Work area should be properly lighted.
• Proper electrical recepta_e should be avai)aPle for
tool. Three prong plug should be plugged directly
Into proper_ygrounded, three-prong receptacle.
o Extension cords should have a grounding prong and
the three wires of the extension cord should be of
the correct gauge.
* Keep visitors at a safe distance frorn work area.
• Keep children out of workplace. Make workshop child-
proof. Use padlocks, master switches or remove switch
keys to prevent any unintentional use of power tools.
TOOL SHOULD BE MAINTAINED
• Always unplug tool prior to inspection.
• Consult manual for specific maintaining and adjust-
Ing procedures.
• Keep tool lubricated and clean for safest operation,
• Remove adjusting feoJs. Form habit of checking to
see that adjusting tools are removed before sw{teh-
ing machine on.
• Keep all parts in working order. Check to determine
that the guard or other parts will operate properly
and perform their intended function,
• Check for damaged parts. Check for alignment of
moving parts, binding, breakage, mounting and any
other condition that may affect a tool's operation.
o A guard or other pa_ that is d_'nagsd sh_d be
properly repaired or replaced. Do not perform
makeshift mpalm. (Use parts list provided to order
replacement parts.)
KNOW HOWTO USE TOOL
= Use right tool for job. Do not force tool or attachment
to do a job for which it was not designed.
• Disconnect too) when changing b}sdes.
• Avoid accidental start-up, Make sure that the switch
is in the OFF position before plugging in.
• Do not force tool. it will work most efficiently a_ the
rate for which it was designed.
• Keep hands away from moving parts and cutting
sul'_ces.
• Never leave toot running unattended. Turn the power
off and do not leave tool until it comes to a complete
stop.
• Do not overreach. Keep proper footing and balance.
• Never stand on tool. Serious injury could occur if tool is
tipped or if blade is unintentionallycontacted.
• Know your tool. Learn the tool's operation, applica-
tion and specific limitations.
• Use recommended accessories (refer to page 15).
Use of improper accessories may cause risk of
injury to persons.
2