Table of Contents
Advertisement
Available languages
Available languages
APE1
SERIES
Page 2
CLEANING
& MAINTENANCE
For performance,
appearance,
and health reasons, clean filter,
fan and grease-laden surfaces. Use only a clean cloth and mild
detergent solution on stainless and painted surfaces. Clean all-
metal filters in the dishwasher.
The motor is permanently
lubricated and never needs oiling. If
the motor bearings make excessive or unusual noise, replace
the motor with the exact service motor. The impeller should also
be replaced.
Use 120 V, 42 W fluorescent lamp GX24Q-4. For night light, use
4 W, C-7 bulbs. (Bulbs included with hood.)
The grease filters, bottom panel, and blower wheel should be
cleaned frequently. Use a warm detergent solution. The grease
filters and blower wheel are dishwasher safe.
Note: Some minerals, when in contact with dishwasher
soap
additives, may cause filters to discolor. This discoloration is not
covered by the warranty.
PREPARE HOOD LOCATION
ROOF CAP
3%"X
10"
(For vertical
HOUSE
WIRING
or Back of hood)
WALL CAP
--_
3¼" X 10" DUCT
(For horizontal
discharge
18" - 24" ABOVE
COOKING
SURFACE
OPERATION
Always turn the hood ON before cooking in order to establish an
air flow in the kitchen. After turning off the range, let the hood run
for a few minutes to clear the air.
HEAT SENTRY
TM
The hood is equipped with a Heat Sentry
TM
thermostat.This safety
device will turn on or speed up the blower if it senses excess heat
above the cooking surface.
If the blower is not on, or if it is running at low speed, the Heat
Sentry
TM
will override the normal blower control and run the blower
on the high speed. When the temperature
level drops to normal
levels, the blower will return to its original setting.
Operate the hood as follows:
O
•
ON
FAN
OFF
FAN
LIGHT
BR_N
0
FAN
The 2-position switch (in center) turns blower ON and OFR
The 5-position switch (at left) controls blower speed.
O Blower is OFF (secondary blower OFF).
•
Blower is ON at highest speed.
• o • As dots get smaller - blower speed decreases.
LIGHT
This 3-position switch (at right) turns lights ON and OFF and
controls their intensity.
O Lights are OFR
Night Light is ON.
Fluorescent Light is ON.
El
Determine whether hood will discharge vertically or horizon-
tally. For vertical or horizontal discharge, run ductwork be-
tween the hood location and a roof cap or wall cap. For best
results, use a minimum number of transitions and elbows.
[_
Use the
diagram below, for placement of ductwork
proper
and electrical cutout in cabinet or wall. For a non-ducted
installation, DO NOT cut a duct access hole.
I
3%" X 10"
HOOD MOUNTING SCREWS (4)
VERTICAL DUCTING
1315/16"
(30"
hood)
11
315/16" (30"
hood)
w
_-1615/16
'' (36" hood)
-T-1615/16
'' (36" hood)
I-CABINET FRONT J
-.L
rT_7,1
--i
CABINET
|
1
I
I[_
11/2''
I I I"_!
67/8''
BOTTOM
_
7 /2" --_
I[_'i|
I 17
Iil',/
V
I
\,
'
\ WOOD
SHIMS
t
ELECTRICAL
(recessed-bottom CENTER
ACCESS HOLE
cabinets o nly)
LINE
(in c abinet b ottom)
WOOD
SHIMS
31A"X
10"
(recessed-bottom
VERTICAL DUCTING
cabinets only)
CABINET FRONT
3/4"
1/8"
,_,J_J II
I
.OR,ZO,TALOUCT
T
JBOTTOM J-_,--- 6%'_--
6%_
13W16"(30"hood) _
71/2"
I'_"'-_1
........
_ "_
I J'u/16
(30'
It)
a/16
136
hood)
ooa)
I
1 615/16"
(36" hood)
HOOD
_'
ELECTRICAL
MOUNTING
CENTER
ACCESS HOLE
SCREWS (4)
LINE
(in wall)
Advertisement
Table of Contents
