Introduction; Selecting Location; Minimum Clearances - Desa C36EMW Installation Instructions Manual

FOR YOUR SAFETY
•
Do not store or use gasoline or any other flammable
vapors or liquids in the vicinity of this or any other
appliance.
•
Due to high temperatures, the appliance should be
located out of traffic and away from furniture and
draperies.
•
Do not place clothing or other flammable materials on
or near the appliance.
•
NEVER leave children unattended when a fire is
burning in the fireplace.
WARNING: Improper installation, adjustment,
alteration, service or maintenance can cause injury,
property damage, or loss of life. Refer to this manual
for assistance or additional information.
qualified installer or local distributor.
CHECK HUD REQUIREMENTS BEFORE
INSTALLING THIS FIREPLACE.

INTRODUCTION

BEFORE BEGINNING THE INSTALLATION OF THE
FIREPLACE, READ THESE INSTRUCTIONS THROUGH,
COMPLETELY.
♦ This DESA fireplace and its components are safe
when installed according to this installation manual.
Unless you use DESA components, which has been
designed and tested for the fireplace system, you may
cause a fire hazard.
♦ The DESA warranty will be voided by and DESA
disclaims any responsibility for the following actions:
a) Modification of the fireplace, components, doors,
blower, fans, air inlet system and damper control.
b) Use of any component part not manufactured or
approved by DESA in combination with a DESA
fireplace system.
PROPER INSTALLATION is the most important step in
ensuring safe and continuous operation of the fireplace.
Consult the local building codes as to the particular
requirements concerned with the installation of all factory
built fireplaces. Although grounding may not be required by
code the manufacturer recommends it.
This Model fireplace C36EMW meets the construction
and safety standards of HUD for application in mobile
homes when installed according to these instructions.
WARNING: Do not install a fireplace insert in
this box unless the manufacturers instructions with
the insert specifically state this fireplace has been
tested for use with the insert.
This fireplace is not intended to be used as a substitute for
a furnace to heat an entire home. Use for supplemental
heat only.
USE SOLID WOOD OR PROCESSED SOLID FUEL
FIRELOGS ONLY.
are used, do not poke or stir the logs while they are
burning. Use only fire logs that have been evaluated for
the application in fireplace and refer to fire log warnings
and caution markings on packaging prior to use.
This wood burning fireplace complies with UL 127
standard as a FACTORY BUILT FIREPLACE.
CAUTION: The structural integrity of the mobile home
floor, and ceiling/roof must be maintained.

SELECTING LOCATION

To determine the safest and most efficient location for the
fireplace, you must take into consideration the following
guidelines:
Consult a
1.) The location must allow for proper clearances (see
2.) Consider a location were the fireplace would not be
3.) A location that avoids the cutting of joists or roof
4.) An outside air kit is included with this fireplace. For
MINIMUM CLEARANCES TO COMBUSTIBLES
•
Back and side of fireplace -------------- ¾" minimum
Note: The ¾" clearance is not required at the nailing flanges
•
Floor* -------------------------------------
*See step 2 of "Installing the Fireplace" on page 3
•
Perpendicular Wall to Opening of unit - 12" minimum
•
Top Spacers ------------------------------
•
Mantel Clearances -------------- see page 8 "Mantels"
•
Chimney Outer Pipe Surfaces ---------
insulation or other materials.
MINIMUM / MAXIMUM CHIMNEY HEIGHT
The minimum height of the chimney, measured from the base
of the fireplace to the flue gas outlet of the termination, is 11.5
feet for straight flue or a flue with one elbow set.
maximum distance between elbows is 2 feet. For systems
with 2 elbow sets, minimum height is 22 feet. The maximum
height of any system is 28 feet. This measurement includes
the fireplace, chimney sections and the height of the
termination assembly at the level of the flue gas outlet (see
page 6, figure 15).
FRAMING AND INSTALLING THE FIREPLACE
STEP 1: Frame the opening for the fireplace using the
dimensions shown in figures 1 & 2.
STEP 2: If the fireplace is to be installed directly on carpeting,
tile (other than ceramic), or any combustible material other
than wood flooring, the fireplace must be installed upon a
metal or wood panel extending the full width and depth of the
fireplace.
-2 -
WARNING: When processed wood fuel fire logs
figures 1 & 2).
affected by drafts, air conditioning ducts, windows or
doors.
rafters will make installation easier.
more details refer to section on outside air kit
installation on page 4.
WARNING: Do not install in a bedroom.
WARNING: Do not pack required air spaces with
For more information, visit www.desatech.com
0" minimum
0" minimum
1" minimum
The