Advertisement
Quick Links
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING LUMINAIRE
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTRUCTION SHEET FOR 9",12"&16" PENDALYTE™ SERIES DECO SUSPENSION KIT
Note: This instruction sheet covers several luminaire styles. Powerhead assembly, lamp type, and reflector style may vary slightly from that
shown, although installation is the same.
CANOPY INSTALLATION (fig. 1):
1.
Thread STUDS into CROSSBAR as shown.
2.
Using appropriate slots in CROSSBAR, secure CROSSBAR to outlet box using OUTLET BOX SCREWS (provided with outlet box).
3.
Make electrical connections: black POWERCORD lead to hot (black) supply lead; white POWERCORD lead to neutral (white) supply
lead. Green POWERCORD lead is ground wire and must be connected to grounding terminal or ground lead inside outlet box. Use
WIRE NUTS (local hardware item). Push supply leads into outlet box. Note: Refer to POWERHEAD instruction sheet for detailed
wiring information.
4.
Secure POWERCORD into CANOPY with RELIEF BUSHING.
5.
Position CANOPY over STUDS and secure with CAP SCREWS.
POWERHEAD INSTALLATION (fig. 2):
Note: On 9" unit MOUNT PLATE must be oriented correctly to clear DOOR SCREW head
(see fig. 2).
1.
Pass POWERCORD through relief bushing hole in MOUNT PLATE.
2.
While supporting POWERHEAD ASSEMBLY wire luminaire using WIRE NUTS (local
hardware item): black luminaire lead to hot (black) POWERCORD lead, white luminaire
lead to neutral (white) POWERCORD lead. Attach luminaire ground wire(s) (green and/or
bare) to green ground wire from POWERCORD.
3.
Height adjustment: to raise luminaire push excess POWERCORD down into
POWERHEAD. (Make certain CABLE does not interfere with internal wiring or
components, both POWERCORD and CABLE may be cut inside POWERHEAD. Remove
DOOR SCREW and pull DOOR away from POWERHEAD).
4.
Secure POWERCORD to MOUNT PLATE with RELIEF BUSHING.
5.
Attach MOUNT PLATE to POWERHEAD with 8-32 SCREWS and plug center hole with
SNAP-IN PLUG.
SCREW HEAD / LANCED TAB
PLUNGER
Fig. 3
Fig. 4
CAUTION: MAKE CERTAIN WIRES
TUBE CLIP
ARE NOT PINCHED BETWEEN PARTS.
CABLE
ADJUSTER
DECO TUBE INSTALLATION (fig. 3)
1.
Slip bottom of TUBE CLIP over TAB on bottom
of POWERHEAD.
DECO
2.
Pivot top of DECO TUBE assembly until top
TUBES
of TUBE CLIP snaps over SCRE HEADS (9"
units) or LANCED TABS (12"&16" units).
3.
Repeat for remaining tube assemblies
4.
CABLES are inserted into CABLE
ADJUSTERS. Raise luminaire by providing
slack in CABLE and pushing through CABLE
ADJUSTERS. Lower luminaire by depressing
PLUNGER.
TAB
DISC
CAP NUTS
DIFFUSER DISC INSTALLATION (fig. 4)
1.
Install DECO TUBE assemblies to
POWERHEAD first.
2.
Align holes in DISC with ends of
DECO TUBES.
3.
Secure with CAP NUTS.
CAUTION: MAXIMUM WATTAGE AS MARKED ON LUMINAIRE
MUST NOT BE EXCEEDED.
631 Airport Road, Fall River, MA 02720
INSTRUCTION SHEET NO.
IS:409DK
A0404
WIRE NUT
CABLES
RELIEF
BUSHING
WIRE NUT
A
Page 1 of 1
CROSSBAR
OUTLET BOX
SCREWS
STUDS
RELIEF
BUSHING
CAP SCREWS
Fig. 1
POWERCORD
SNAP-IN
PLUG
8-32
SCREWS
MOUNT
PLATE
DOOR SCREW
DOOR
POWERHEAD
Fig. 2
COMPANY
Advertisement
