Table of Contents
Advertisement
NORMAL PLAYBACK
1
Insert a prerecorded tape. The VCR will turn
on.
¡
If the safety tab has been removed, the
VCR will start playback automatically.
2
Turn on the TV and set the TV to channel 3.
¡
If noise appears, change the RF output channel of the
VCR to channel 4 by pressing PLAY for 3 seconds dur-
ing playback. Then select the same channel (CH4) on
your TV. (See "RF OUTPUT CHANNEL" on page 13
for the detail.)
3
Begin playback by pressing PLAY.
¡
Tracking adjustment will be done automatically
(Digital Tracking function) when you start playback.
To adjust the tracking manually, press SKIP/CH. on
the remote or CHANNEL (o/p) on the VCR.
¡
When a tape has reached the end, the VCR will
rewind the tape to the beginning, and eject the tape.
4
To stop playback, press STOP.
¡
If no corresponding symbols appear on the display
when you press buttons such as PLAY, RECORD,
D or E, that means no cassette tape is in the
VCR. Please insert a tape.
Counter Reset
¡
You can reset the counter by pressing
CLEAR/C.RESET on the remote control twice.
STILL/SLOW
You can freeze the picture on TV screen by pressing
PAUSE during playback.
¡
You can advance the picture one frame at a time by
pressing PAUSE during the Still mode.
¡
You cannot manually adjust the tracking of a still
picture. However, if the picture begins to vibrate
vertically during the still mode, you can stabilize the
picture by pressing CHANNEL (o/p).
¡
If the picture is distorted or rolling vertically, adjust
the vertical hold control on your TV, if so equipped.
¡
You can watch in the slow motion by pressing
SLOW during playback or the still mode.
¡
If a noise bar appears on the TV screen, you can
reduce it by pressing CHANNEL (o/p).
¡
After the VCR has been in Still/Slow mode for 5
minutes, it will stop automatically to protect the tape
and the video head from damage.
¡
To return to playback, press PLAY.
AUTO REPEAT PLAYBACK
This feature allows you to play a tape over and over.
1
Select main menu by pressing MENU.
PLAYBACK FUNCTION
VCR
¡
¡
PICTURE SEARCH
If you want to skip or repeat a scene during playback,
press D or E.
¡
INDEX SEARCH
An index mark will be assigned at the beginning of
each recording you made. You may skip to a specific
marked point by following the steps below.
¡
¡
¡
¡
TIME SEARCH
This feature allows you to go to a specific point on a
tape by entering the exact amount of time you wish to
skip in order to reach the point.
¡
VCR
¡
¡
¡
– 18 –
2
Select "AUTO REPEAT" by pressing K or L.
3
Begin auto repeat playback by pressing
so that ON appears next to "AUTO
REPEAT".
If the on-screen menu still remains, CLEAR/C.RESET
to exit the menu.
To cancel the Auto repeat mode, press B at step [3]
so that OFF appears next to "AUTO REPEAT".
SEARCH FUNCTIONS
Press it again and the VCR will now search at super
high speed. (in the LP/SLP modes only).
1
Press SEARCH MODE so that the Index
Search menu appears.
2
Enter the number of recordings you wish to
skip by pressing K or L
within 30 seconds.
3
Press
or { to start index search.
B
If you want to go in the forward direction, press B .
If you want to go in the reverse direction, press
If you want to stop search function, press STOP.
After index search, the VCR will play the tape auto-
matically.
1
Press SEARCH-MODE so that the Time
Search menu appears.
2
Enter your desired time to
skip by pressing K or L
within 30 seconds.
3
Press B or { to start time search.
If you want to go in the forward direction, press
If you want to go in the reverse direction, press
If you want to stop search function, press STOP.
After time search, the VCR will play the tape auto-
matically.
B
VCR
INDEX SEARCH
03
.
{
TIME SEARCH
2 : 50
.
B
.
{
EN
1L25
Advertisement
Table of Contents
