Table of Contents
Related Manuals for Cornelius D3030
Summary of Contents for Cornelius D3030
- Page 1 ICE/DISPENSER Model D3030 Part No 91875. March, 1997 Revision C THIS DOCUMENT CONTAINS IMPORTANT INFORMATION This Manual must be read and understood before installing or operating this equipment IMI CORNELIUS INC; 1989-95 Ó PRINTED IN U.S.A...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Page SAFETY PRECAUTIONS ........... GENERAL DESCRIPTION . -
Page 3: Safety Precautions
SAFETY PRECAUTIONS Always disconnect power to the dispenser before servicing or cleaning. Never place hands inside of hopper or gate area without disconnecting power to the dispenser. Agitator rota- tion occurs automatically when the dispenser is energized! This ice dispenser has been specifically designed to provide protection against personal injury and eliminates contamination of ice. -
Page 4: Installation Instructions
INSTALLATION INSTRUCTIONS 1. The ice dispenser must be sealed to the counter. The template drawings (page 4) indicate openings which must be cut in the counter. Locate the desired position for the dispenser, then mark the outline dimensions and cut out locations using the template drawing. Cut openings in the counter. Apply a continuous bead of NSF International (NSF) approved silastic sealant (DOW 732 or equal) approxi- mately 1/4”inside of the unit outline dimensions and around all openings. -
Page 5: Adjustment
ADJUSTMENTNO TAG This dispenser is provided with a gate restrictor plate, installed in its’highest position. This plate adjusts the rate of ice flow from the dispenser. In applications using buckets, carafes or other large containers, the plate may be removed entirely for maximum ice flow. For glasses and cups, the plate may be adjusted downward to reduce the flow of ice. -
Page 6: Figure 2. Mounting Templates
NOTE: shaded area indicates opening in cabinet bottom needed for utilities and beverage tubing. FIGURE 2. MOUNTING TEMPLATES 91875... -
Page 7: Operating Instructions
OPERATING INSTRUCTIONS Fill the hopper with ice and replace the lid. Pushing the dispenser lever will cause ice to flow from the ice chute. Ice flow will continue until the lever is released. If ice does not dispense see the TROUBLESHOOTING GUIDE to find the cause. - Page 8 5. Sanitize the inside of the hopper and agitator with a solution of 1/2 ounce of household bleach in 1 gallon of water. (200 PPM) 6. Replace the agitator disk. Sanitize as described in Step 5. Be sure the center screw is replaced and the screw is tight.
-
Page 9: Troubleshooting Guide
TROUBLESHOOTING GUIDE Should your unit fail to operate properly, check that there is power to the unit and that the hopper contains ice. If the unit does not dispense, check the following chart under the appropriate symptoms to aid in locating thede- fect. -
Page 10: Figure 3. Wiring Diagram
WHEN REPLACING SOLENOID, ADJUST TO 7/8 INCH AS SHOWN BEFORE TIGHTENING MOUNTING SCREWS. FIGURE 3. WIRING DIAGRAM 91875... - Page 11 FIGURE 4. SOLENOID ASSEMBLY Index Part No. Qty. Name 21493 Solenoid mounting plate 31551 Solenoid service kit 70171 8--32 x 3/8 Phil Tr HD Screw 70121 No. 8 lockwasher 50752 Isolator 50789 Bumper Assembly 70423 Cotter Pin 10080 Gate Lift Rod 10081 Gate Lift Rod Bushing 50754...
- Page 12 FIGURE 5. EXPLODED ASSEMBLY (UPPER) 91875...
- Page 13 PARTS LIST Item Part No. Name 21491 Gate Slide 21515 Depressor Lever - Cup Activated 22644 Depressor Retainer (for 21515) 27126 Depressor Push Lever 27107 Depressor Retainer (for 27126) 28075 Agitator 02070 Depressor Switch Kit 31007 Switch Boot 31163 Switch Insert 70847 Switch Spacer 52239...
- Page 14 FIGURE 6. EXPLODED VIEW - UPPER SECTION AND PARTS LIST Item Part No. Name 21491 Gate Slide 28075 Agitator 52239 Foam Shield 52154 Lid - Gray 53015 Ice Chute (Clear) Back Section 53016 Ice Chute Cover 51891 Gate Gasket 90295 Cleaning label 91680 Wiring Diagram (Pull Solenoid)
- Page 15 FIGURE 7. EXPLODED VIEW - LOWER SECTION AND PARTS LIST Item Part No. Name 21515 Depressor Lever - Cup Activated 22644 Depressor Retainer (for 21515) 27126 Depressor Push Lever 27107 Depressor Retainer (for 27126) 02070 Depressor Switch Kit 31007 Switch Boot 70847 Switch Spacer 52216...
- Page 16 FIGURE 8. MOTOR ASSEMBLY DETAIL AND PARTS LIST Item Part No. Name 32939 Agitator Motor 51101 Motor Shaft Seal 30794 Agitator Motor Heater 33160 Capacitor 70963 Clamp 33162 Relay 70032 1/4-20 x 1/2 Zinc Plated HH Screw 28377 Bracket, Back, Motor Plate 28378 Bracket, Motor Plate 70250...
-
Page 17: Warranty
IMI Cornelius Inc. warrants that all equipment and parts are free from defects in material and workmanship un- der normal use and service. For a copy of the warranty applicable to your Cornelius product, in your country, please write, fax or telephone the IMI Cornelius office nearest you. Please provide the equipment model number and the date of purchase. - Page 18 IMI CORNELIUS INC. Corporate Headquarters: One Cornelius Place Anoka, Minnesota 55303-6234 (612) 421-6120 (800) 238-3600...