Automatic Tuning; Manual Tuning - Hitachi DVPF3EUK Instruction Manual

AUTOMATIC TUNING

You can programme the tuner to scan only the chan-
nels that you can receive in your area.
• Use the remote control for this procedure.
1
Turn on the TV and select the TV channel to
the video channel on the TV.
2
Press MENU.
3
Press Arrow (
o
press Arrow (
B
4
Press Arrow (
o
then press Arrow (
5
Press Arrow (
o
press Arrow (
B
• The tuner scans and memorises all the active chan-
nels in your area. After scanning, the tuner stops on
the lowest memorised channel.
• Sorting of TV channels from P01 to P06 will be per-
formed automatically as follows.
P01: BBC1 P02: BBC2
P04: CH4 P05: CH5
*If you are using a satellite receiver, turn it on and
select Sky News before commencing tuning.
To Select a Desired Channel
You can select a desired channel by using
the PROG (o/p), or directly pressing Number on
the remote control.
• Enter a channel numbers as a two-digit number for
the quickest results. For example, to select channel 6,
press 0 and 6. If you only press 6, channel 6 will be
selected after a brief delay.
• You can only select channels 1–99.

MANUAL TUNING

• Use the remote control for this procedure.
1
Press MENU.
2
Press Arrow (
o
press Arrow (
B
/p) to select "INITIAL", then
).
MENU
TIMER
SET UP
INITIAL
/p) to select "CH TUNING",
).
B
INITIAL
CH TUNING
CLOCK
RF OUT
/p) to select "AUTO", then
).
CH TUNING
AUTO
MANUAL
MOVE
P03: ITV
*(P06: Sky News)
/p) to select "INITIAL", then
).
MENU
TIMER
SET UP
INITIAL
3
Press Arrow (
then press Arrow (
VCR
4
Press Arrow (
then press Arrow (
5
Press Arrow (
then press Arrow (
• When a weak signal is received
in Manual Tuning mode, you can change the back-
ground to solid blue or the static screen by pressing
CLEAR/C.RESET.
6
Press Number, or Arrow (
your desired position number, then press
Arrow (
• You can select position number 01-99.
• If [ON] appears on the right side of "SKIP", press
Arrow ( /p)
o
to select [OFF].
( )
B
• If you want to remove scrambled signals, press
repeatedly to point to "DECODER". Then,
( /p)
o
press
Arrow (
7
Press Arrow (
then press Arrow (
8
Press Arrow (
• The DVD/VCR tuner will begin to search up or down
automatically. When a channel is found, the
DVD/VCR will stop searching and the picture will
appear on the TV Screen.
• You can select desired channel number by using the
Number Buttons. You must refer to the channel plan
and press three digits to select the channel number.
(To select channel 24, first press "0" and then press
"2" and "4").
• If this is the channel you want, press
CH Indication
01 – 10
21– 69
74 – 78
80 – 99,100
VCR
121 – 141
This DVD/VCR can receive Hyper and Oscar frequency bands.
9
Press MENU to exit.
Note
To confirm that a channel has been added, press PROG
(o/p).
– 19 –
/p) to select "CH TUNING",
o
).
B
/p) to select "MANUAL",
o
).
B
/p) to select "POSITION",
o
).
B
/p) to select
o
).
B
to point to "SKIP". Then, press
to select [ON].
)
B
/p) to select "CHANNEL",
o
).
B
/p) to start scanning.
o
Arrow (
Channel Plan
TV Channel
IRA – IRJ, GAP
E21 – E69
X, Y, Z, Z+1, Z+2
S1 – S20, GAP
S21 – S41
INITIAL
CH TUNING
CLOCK
RF OUT
CH TUNING
AUTO
MANUAL
MOVE
MANUAL
P08
POSITION
008
CHANNEL
DECODER [OFF]
[OFF]
SKIP
Arrow
Arrow
.
)
B
EN
2C15