Table of Contents
Advertisement
Your straight finish nailer has been engineered and manufactured to our high standard for dependability, ease of operation,
and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator's manual before using
this product.
Thank you for your purchase.
SAVE THIS MANUAL FOR FUTURE REFERENCE
OPERATOR'S MANUAL
16 GAUGE STRAIGHT FINISH NAILER
YN250FS
Advertisement
Table of Contents
Related Manuals for Ryobi YN250FSD
Summary of Contents for Ryobi YN250FSD
- Page 1 OPERATOR’S MANUAL 16 GAUGE STRAIGHT FINISH NAILER YN250FS Your straight finish nailer has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
-
Page 2: Table Of Contents
The replacement power tool will be covered by the limited warranty for the balance of the two year period from the date of the original purchase. WHAT THIS WARRANTY COVERS: This warranty covers all defects in workmanship or materials in your RYOBI power ®... -
Page 3: General Safety Rules
GENERAL SAFETY RULES Do not overreach. Keep proper footing and balance DANGER: at all times. Proper footing and balance enables better control of the tool in unexpected situations. READ AND UNDERSTAND TOOL LABELS AND Use safety equipment. Always wear eye protection. MANUAL. -
Page 4: Specific Safety Rules
SPECIFIC SAFETY RULES OPERATION Know your pneumatic tool. Read operator’s manual carefully. Learn its applications and limitations, as well Always assume that the tool contains fasteners. as the specific potential hazards related to this tool. Do not carry the tool from place to place holding the Following this rule will reduce the risk of electric shock, trigger. - Page 5 SPECIFIC SAFETY RULES Always disconnect air supply: During normal use the tool will recoil immediately after driving a fastener. This is a normal function of the tool. • Before making adjustments Do not attempt to prevent the recoil by holding the nailer •...
-
Page 6: Symbols
AUTHORIZED SERVICE CENTER for repair. When servicing, do not understand the warnings and instructions in the use only identical replacement parts. operator’s manual, do not use this product. Call Ryobi customer service for assistance. WARNING: The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. -
Page 7: Glossary Of Terms
GLOSSARY OF TERMS Activate (operating controls) Operating control To move an operating control so that it is in a position that A control that separately, or as part of an actuation system, allows the tool to be actuated or that satisifes one requirement can cause the actuation of a tool. -
Page 8: Features
FEATURES PRODUCT SPECIFICATIONS Operating Pressure..........70-10 psi Air Consumption......0.05 ft /cycle at 100 psi Fastener Type ........16 gauge finish nails Air Inlet .............. 1/4 in. NPT Weight ................ 4 lbs. Fastener Range ..........1 in. to -1/ in. Magazine Capacity ..........110 nails adJUsTaBle eXHaUsT Trigger... -
Page 9: Assembly
FEATURES JAM RELEASE KNOW YOUR STRAIGHT FINISH NAILER See Figure 1. A tool-free jam release is provided for ease in clearing The safe use of this product requires an understanding of infrequent jams. the information on the product and in this operator’s manual NO-MAR NOSEPIECE as well as a knowledge of the project you are attempting. -
Page 10: Operation
OPERATION APPLICATIONS DANGER: You may use this tool for the purpose listed below: Do not use oxygen, combustible gases or bottled gases Finish and Trim (Interior and exterior) as a power source for this tool. The tool will explode and ... - Page 11 OPERATION WARNING: QUicK-coNNecT air fiTTiNg Always wear eye protection. Eye protection does not fit all operators in the same way. Make sure the eye protection chosen has side shields or provides protection from flying debris both from the front and sides. PREPARING THE TOOL FOR USE See Figure 2.
- Page 12 OPERATION WARNING: QUicK-coNNecT Disconnect the tool from the air supply before leaving the air fiTTiNg work area, moving the tool to another location, or handing the tool to another person. Failure to do so could result in serious personal injury. CONNECTING THE TOOL TO AN AIR SUPPLY See Figure 5.
- Page 13 OPERATION LOADING THE TOOL WITH NAILS See Figures 6 - 7. Connect the tool to the air supply. WARNING: Nails The tool’s driving mechanism may cycle when the tool is first connected to the air supply. Always connect the tool to the air supply before loading nails to prevent injury from unintended cycling.
- Page 14 OPERATION DRIVING A FASTENER See Figure 8. WARNING: Never wedge or hold back the workpiece contact mechanism during operation of the tool. Doing so could result in possible serious injury. SINGLE SEQUENTIAL ACTUATION Trigger Single sequential actuation provides accurate fastener placement.
- Page 15 OPERATION SETTING THE AIR PRESSURE The amount of air pressure required will depend on the size of the nail and the workpiece material. Begin testing the depth of drive by driving a test nail into the same type of workpiece material used for the actual job. To decrease To iNcrease depTH...
- Page 16 OPERATION WARNING: Disconnect the tool from the air supply before clearing a jammed fastener. Failure to do so could result in serious personal injury. CLEARING A JAMMED FASTENER See Figure 11. If a nail or fastener becomes jammed in the tool, disconnect the air hose and keep the tool pointed away from you while clearing the jam.
-
Page 17: Maintenance
MAINTENANCE LUBRICATION WARNING: Frequent, but not excessive, lubrication is required for best performance. Oil for pneumatic fastening tools added through When servicing use only identical replacement parts. the air line connection will lubricate the internal parts. Do Use of any other parts may create a hazard or cause not use detergent oil or additives as these lubricants will product damage. -
Page 18: Accessories
MAINTENANCE REQUIRED DAILY CHECKLIST With the workpiece contact not engaged on the workpiece, point the tool down and away and pull the Disconnect the air supply from the tool and remove all trigger several times. Hold the trigger in this position for fasteners. -
Page 19: Troubleshooting
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Air leak near the top of the tool or Loose screws Tighten screws in the trigger area Worn or damaged O-rings or Install Overhaul Kit seals Air leak near the bottom of the Worn or damaged O-rings or bumper Install Overhaul Kit tool Tool does nothing or operates... - Page 20 HOW TO OBTAIN CUSTOMER OR TECHNICAL SUPPORT: To obtain Customer or Technical Support please contact us at 1-800-55-579. Ryobi is a registered trademark of Ryobi Limited used under license. ® ONE WORLD TECHNOLOGIES, INC. 148 Pearman Dairy Road, Anderson, SC 965 Phone 1-800-55-579 www.ryobitools.com...