Summary of Contents for Elo TouchSystems Entuitive 1225L Series
Page 2
Elo TouchSystems reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of Elo TouchSystems to notify any person of such revisions or changes.
Table of Contents Usage Notice Precautions ... 3 Introduction About the Product ... 4 Package Overview ... 5 Installation Product Overview ... 6 Start Your Installation ... 7 User Controls Front Panel Controls ... 9 How to Use the OSD Menus ... 10 On-Screen Display Menus ...
Usage Notice To prevent the risk of fire or shock hazards, do not Warning- expose this product to rain or moisture. Do not open or disassemble the product as this Warning- may cause electric shock. Precautions Follow all warnings, precautions and maintenance as recom- mended in this user’s manual to maximize the life of your unit.
31 ~ 54kHz horizontal scan 56 ~ 85Hz high refresh rate Multilingual OSD user controls VESA DPMS power saving Serial touch interface (RS232 cable) Built-in speakers Patented touch technology of Elo TouchSystems. For full product specifications refer to Touchmonitor Specifications , page...
Package Overview Check that the following 10 items are present and in good condition: LCD Touchmonitor VGA Signal Cable Manual Software User’s Guide and software CD Mac Video Adapter Audio-In Cable US/Canada Power Cord Power Adapter European power cable RS-232 Touchscreen Interface Cable...
Installation Product Overview Main Unit Stand Rear View Power Switch LCD Touchmonitor User Controls MENU SELECT Audio Display Power Input Phone DC-In RS-232 Touch Interface...
Start Your Installation Connecting the Touchmonitor (Figure 7.1) To setup this touchmonitor, please refer to the following figure and proce- dures. 1. Be sure all equipment is off. 2. Connect the VGA signal cable from display input connector to the 15-pin connector of your host computer and tighten the screws.
Page 9
Audio-In Cable Notice: To ensure the LCD display works well with your computer, please configure the display mode of your graphic card to less than or equal to 800 x 600 resolution. Make sure the timing of the display mode is compatible with the LCD display. We have listed the Compatibility Modes of this LCD display in the appendices for your reference.
User Controls Front Panel Controls MENU SELECT No. / Icon Control MENU Menu button SELECT Select Decrease / Select Increase / Select Power LED Function Displays the OSD menus Selects the adjustment items from OSD menus.
How to Use the OSD Menus 1. Press the “MENU” button to pop up the on-screen menu and to toggle between Main Menu Page 1 to Page 3. 2. Choose the adjustment items by pressing the “ SELECT” button. 3. Adjust the value of adjustment items by pressing the “ 3 ” & “ 4 ” buttons.
On-Screen Display Menus First OSD Menu: Brightness Contrast Horizontal Position Vertical Position Frequency Tracking Brightness Adjusts the brightness of the image. Contrast Adjusts the contrast of the display image. Horizontal Position Adjusts the horizontal position of the image. Vertical Position Adjusts the vertical position of the image.
Page 13
Second OSD Menu: Auto-Adjustment Re-Scaling Display Mode OSD Off-Time Language Text-Graphic 4Auto-Adjustment Choose this function to obtain an optimum image. 4Re-Scaling If the input resolution is less than 800 x 600, you can select this function to obtain the full screen image. Display Mode Select this function to demonstrate the display resolution, vertical refresh, and horizontal scan of the current mode.
Page 14
Third OSD Menu: Volume Mute Reset Volume Allows you to control the volume of sound, Mute Allows you to disable the sound immediately. Reset Returns the display parameters of the current mode to the factory defaults. Main Menu Page 3...
If the problem persists, please contact your local dealer or our service center. Please refer to the back cover of this manual for the phone number of the Elo TouchSystems office nearest you. Problem: No image appears on screen.
Warning Signal Sometimes you will see warning messages from the LCD screen. This means that the LCD display cannot receive the signal from the computer graphic card. There are three situations where this may happen. Please check the connected cables or contact your local dealer for more information. No Signal This message means that the LCD display has been powered on but it cannot receive any signal from the computer graphic card.
Windows NT 4.0 Additional drivers and driver information for other operating sys- tems (including MS DOS, Windows 3. x , OS/2, Macintosh and Linux) are available on the Elo TouchSystems web site at www.elotouch.com. Your Elo touchmonitor is plug-and-play compliant. Information on the video capabilities of your touchmonitor is sent to your video display adapter when Windows starts.
Page 22
2. Follow the directions on the screen to complete the driver setup for your version of Windows. If the AutoStart feature is not active: 1. Click Start > Run. 2. Click the Browse button to locate the touch.exe pro- gram on the CD-ROM. 3.
Page 23
To run the INSTALL program: 1. Type INSTALL at the DOS prompt in the directory con- taining the driver install files. 2. INSTALL asks you to select the software to install. Then choose d:\EloDW from the displayed list. 3. INSTALL also asks you for the paths to use during in- stallation, or you may use its defaults.
Regulatory Information I. Electrical Safety Information: A) Compliance is required with respect to the voltage, frequency, and current require- ments indicated on the manufacturer’s label. Connection to a different power source than those specified herein will likely result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed.
Page 25
1) In order to meet emission and immunity requirements, the user must observe the following: a) Use only the provided I/O cables to connect this digital device with any computer. b) To ensure compliance, use only the provided manufacturer’s approved line cord.
Warranty Except as otherwise stated herein or in an order acknowledgment delivered to Buyer, Seller warrants to Buyer that the Product shall be free of defects in materials and workmanship. The warranty for the touchmonitors and compo- nents of the product are: 3 years monitor, 10 years IntelliTouch screen, 5 years AccuTouch screen, 5 years Controller.
Page 27
SELLER’S LIABILITY UNDER THE WARRANTY SHALL BE LIM- ITED TO A REFUND OF THE PURCHASE PRICE OF THE PRODUCT. IN NO EVENT SHALL SELLER BE LIABLE FOR THE COST OF PRO- CUREMENT OR INSTALLATION OF SUBSTITUTE GOODS BY BUYER OR FOR ANY SPECIAL, CONSEQUENTIAL, INDIRECT, OR INCIDENTAL DAMAGES.