Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Chamberlain 2110 1/3 HP
Summary of Contents for Chamberlain 2110 1/3 HP
- Page 1 GARAGE DOOR OPENER For Residential Use Only Owner’s Manual...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Introduction Pages 2-5 Adjustment Pages 24-26 Operation Pages 27-30 Assembly Pages 6-7 Installation Pages 7-23 Programming Pages 31-32 Repair Parts Pages 33-34 Accessories Repair Parts and Service Warranty INTRODUCTION Safety Symbol and Signal Word Review serious injury or death... - Page 3 Preparing your garage door Tools needed...
- Page 4 Planning...
- Page 5 Carton Inventory ✚ ✚ ✚...
-
Page 6: Assembly
ASSEMBLY STEP 1 Fasten the Rail to the Motor Unit ASSEMBLY STEP 2 Install the Trolley... -
Page 7: Installation
ASSEMBLY STEP 3 Attach the Rail Brackets You have now finished assembling your garage door opener. Please read the following warnings before proceeding to the installation section. INSTALLATION... - Page 8 INSTALLATION STEP 1 Determine the Header Bracket Location Proceed to Step 2, page 10.
- Page 9 NOTE: If the total number of inches exceeds the height available in your garage, use the maximum height possible, or refer to page 10 for ceiling installation. Proceed to Step 2, page 10.
- Page 10 INSTALLATION STEP 2 Install the Header Bracket...
- Page 11 INSTALLATION STEP 3 Attach the Rail to the Header Bracket NOTE:...
- Page 12 INSTALLATION STEP 4 Install The Protector System ® must...
- Page 13 Garage door track installation (preferred): Wall installation: Floor installation:...
- Page 14 Recommended Wire Routing NOTE:...
- Page 15 INSTALLATION STEP 5 Position the Opener...
- Page 16 INSTALLATION STEP 6 Hang the Opener...
- Page 17 INSTALLATION STEP 7 Install the Door Control NOTE: NOTE: Figure 1 Figure 2 (Standard installation only) NOTE: NOTE: 7/16"...
- Page 18 INSTALLATION STEP 8 Install the Lights NOTE: INSTALLATION STEP 9 Attach the Emergency Release Rope and Handle NOTE:...
- Page 19 INSTALLATION STEP 10 Electrical Requirements INSTALLATION STEP 11 Complete Safety Reversing Sensor Installation NOTE:...
- Page 20 INSTALLATION STEP 12 Fasten the Door Bracket NOTE: Metal or light weight doors using a vertical angle iron brace between the door panel support and the door bracket: Metal, insulated or light weight factory reinforced doors: Wood Doors: NOTE:...
- Page 22 INSTALLATION STEP 13 Connect Door Arm to Trolley...
-
Page 24: Adjustment
ADJUSTMENT STEP 1 Adjust the UP and DOWN Travel Limits... - Page 25 ADJUSTMENT STEP 2 Adjust the Force...
-
Page 26: Adjustment
ADJUSTMENT STEP 3 Test the Safety Reversal System ADJUSTMENT STEP 4 Test the Protector System ®... -
Page 27: Operation
OPERATION Using Your Garage Door Opener ✚ ✚ ✚ ✚... - Page 28 Using the Wall-Mounted Door Control To Open the Door Manually °...
- Page 29 CARE OF YOUR OPENER Having a Problem?
- Page 30 Having a Problem? (Continued)
-
Page 31: Programming
PROGRAMMING ✚ To Add an Additional Hand-held Remote Control To Erase All Codes From Motor *3-Channel Remotes Unit Memory ✚ ✚... - Page 32 To Add or Change a Keyless Entry PIN NOTE: Your new Keyless Entry must be programmed to operate your garage door opener. NOTE: This method requires two people if the Keyless Entry is already mounted outside the garage. To change an existing, known PIN hours ✽...
-
Page 33: Repair Parts
REPAIR PARTS Rail Assembly Parts Installation Parts... - Page 34 Motor Unit Assembly Parts LIMIT SWITCH ASSY.
-
Page 35: Accessories
ACCESSORIES ✚ Required ✚ ✚ ✚ ✚ ✚...
Need help?
Do you have a question about the 2110 1/3 HP and is the answer not in the manual?
Questions and answers