Bryant 580G Installation, Start-Up And Service Instructions Manual page 6

UNIT 580G,H
NOMINAL CAPACITY (tons)
OPERATING WEIGHT (lb)
Unit
Al/Al* (Lo Heat/Hi Heat)
Al/Cu* (Lo Heat/Hi Heat)
Roof Curb (14-in. curb)
COMPRESSOR
Type Ckt 1
Ckt 2
Number of Refrigerant Circuits
Oil (oz) (Ckt 1, Ckt 2)
REFRIGERANT TYPE
Operating Charge (lb-oz)
Circuit 1†
Circuit 2
CONDENSER COIL
Quantity
Rows...Fins/in.
Total Face Area (sq ft)
CONDENSER FAN
Nominal Cfm
Quantity...Diameter (in.)
Motor Hp (1075 Rpm)
EVAPORATOR COIL
Rows...Fins/in.
Total Face Area (sq ft)
EVAPORATOR FAN
Quantity...Size (in.)
Type Drive
Nominal Cfm
Motor Hp
Motor Frame Size
Standard
High Efficiency
Motor Bearing Type
Maximum Allowable Rpm
Motor Pulley Pitch Diameter
Nominal Motor Shaft Diameter (in.)
Fan Pulley Pitch Diameter (in.)
Nominal Fan Shaft Diameter (in.)
Belt, Quantity...Type
Belt, Length (in.)
Pulley Center Line Distance (in.)
Factory Speed Setting (rpm)
FURNACE SECTION
Rollout Switch Cutout Temp (F)††
Burner Orifice Diameter
(in. ...drill size)
Natural Gas Std
Liquid Propane Alt
Thermostat Heat Anticipator
Setting (amps)
Stage 1
Stage 2
Gas Input (Btuh) Stage 1 Low
High
Stage 2 Low
High
Efficiency (Steady State) (%)
Temperature Rise Range
Manifold Pressure (in. wg)
Natural Gas Std
Liquid Propane Alt
Gas Valve Quantity
Field Gas Connection Size
(in.-FPT)
HIGH-PRESSURE SWITCH (psig)
Cutout
Reset (Auto.)
LOW-PRESSURE SWITCH (psig)
Cutout
Reset (Auto.)
RETURN-AIR FILTERS
Quantity...Size (in.)
OUTDOOR-AIR FILTERS
Quantity...Size (in.)
POWER EXHAUST
Motor, Quantity...Hp
Fan, Diameter...Width (in.)
LEGEND
Al — Aluminum
Cu — Copper
*Evaporator coil fin material/condenser coil fin material.
†Circuit 1 uses the lower portion of condenser coil; Circuit 2 uses the upper portion. All
units have intertwined evaporator coils.
Table 1 — Specifications
240
20
4176/4256
4396/4476
365
06D328
06D818
2
115, 88
25-0
31-0
Cross-Hatched 3 ⁄
8
1
4...15
33.3
13,420
2...30
1
Cross-Hatched
4...15
31.7
2...20x15
Belt
8,000
5 10** 15 7.5
S184T S215T D254T S213T
S184T S215T S254T S213T
Ball
1200
4.8 4.4 5.7 5.4
1 ⁄ 1 ⁄ 1 ⁄ 1
1 3 5 3
8 8 8
12.4 8.6 9.1 12.4
1 15 ⁄
16
1...BX59 2...BX51 2...5VX530 1...BX59
62 54 53 62
16.0-18.7 15.6-18.4 15.0-17.9
717 924 1096 773
225
.111...34
.089...43
0.1
0.1
262,500
394,000
350,000
525,000
82
15-45/35-65
3.5
3.5
2
1.5
426
320
7
22
10...20x24x2
Direct Drive, 3-Speed, Single Phase Motor (Factory Wired for High Speed), Forward-Curved Fan
300
25
4262/4342
4482/4562
365
06D328
06D328
2
115 ea.
R-22
25-0
25-0
Copper Tubes, Aluminum Lanced, Aluminum Pre-Coated, or Copper Plate Fins
1
4...15
33.3
Propeller Type
13,420
2...30
1
3 ⁄ Copper Tubes, Aluminum Plate Fins, Intertwined Circuits
8
4...15
31.7
Centrifugal Type
2...20x15
Belt
10,000
10** 15 10
S215T D254T S215T
S215T S254T S215T
Ball
1200
6.1 5.5 4.4
⁄ 1 ⁄ 1 ⁄ 1 ⁄
3 5 3
8 8 8 8
11.1 8.7 9.4
1 15 ⁄
16
1...5VX590 2...5VX530 2...BX52
59 53 55
15.6-18.4 15.0-17.9 15.6-18.4
962 1106 848
225
.111...34
.089...43
0.1
0.1
262,500
394,000
350,000
525,000
82
15-45/35-65
3.5
3.5
2
1.5
426
320
7
22
10...20x24x2
8...16×25
4...20×25
4...1
11...10
**Motor and drive shown will deliver approximately 2.5 in. net external static. For more
fan motor data, see Table 2.
††Rollout switch is manual reset.
—6—
324
27
4262/4342 4262/4342
4482/4562 4482/4562
365
06D537 06D537
06D328 06D537
2
115 ea.
25-0
25-0
1
4...15
33.3
13,420
2...30
1
4...15
31.7
2...20x15 2...20x15
Belt
11,000
15** 20 10
D254T S256T S215T D254T
S254T S256T S215T S254T
Ball
1200
4.9 5.9 4.4
1 ⁄ 1 ⁄ 1 ⁄
5 5 3
8 8 8
8.1 8.7 9.0
1 15 ⁄
16
2...5VX500 2...5VX530 2...BX51 2...5VX530
50 53 54
15.0-17.9 15.6-18.4
1059 1187 884
225
.111...34 .111...34
.089...43 .089...43
0.1
0.1
262,500 262,500
394,000 394,000
350,000 350,000
525,000 525,000
82
15-45/35-65 15-45/35-65
3.5
3.5
2
1.5
426
320
7
22
10...20x24x2 10...20x24x2
360
30
365
2
115 ea.
25-0
25-0
1
4...15
33.3
13,420
2...30
1
4...15
31.7
Belt
12,000
15** 20
S256T
S256T
Ball
1200
5.7 5.9
1 ⁄ 1 ⁄
5 5
8 8
9.1 8.7
1 15 ⁄
16
2...5VX530
53 53
15.0-17.9
1096 1187
225
0.1
0.1
82
3.5
3.5
2
1.5
426
320
7
22