Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Bulldog Security DELUXE 200B
Summary of Contents for Bulldog Security DELUXE 200B
- Page 2 Direct Wholesale at www.directwholesale.net. warranty against defects in workmanship, This includes shock sensors, remote transmitters and sirens. The For a full list of Bulldog Security accessories visit our web control module will be repaired or replaced at our dis- site at www.bulldogsecurity.com.
-
Page 3: Table Of Contents
INSTALLATION TABLE OF CONTENTS TRANSPONDER / PASSLOCK III REQUIRED TOOLS ............... 5 INSTALLATION CHECK LIST ............5 TECHNICAL ASSISTANCE ............6 BEFORE YOU BEGIN ..............6 PRECAUTIONS ................. 7-8 USING YOUR TEST PROBE ............8 MAKING WIRING CONNECTIONS ........... 8-10 COMPONENTS ................ - Page 4 TABLE OF CONTENTS TRANSPONDER / PASSLOCK III Dual Pulse Door Unlock Output Note: If the vehicle does not start with the Remote Factory Security Disarm Signal Output Start Status (By-pass Control) Output Starter or runs for approx 5 seconds and shuts H4/9 Blue/Black Wire –...
-
Page 5: Installation Table Of Contents Required Tools
TRANSPONDER / PASSLOCK III TABLE OF CONTENTS routed through the Steering Column and up towards REMOTE START OPERATION ..........39-42 and then around the Ignition Key Cylinder and A. To Remote Start Your Vehicle ........... 39-42 B. To Operate Your Vehicle While Running on the Remote Start ..40 needs to be positioned so that there are at least C. -
Page 6: Transponder / Passlock Iii
TECHNICAL ASSISTANCE TRANSPONDER / PASSLOCK III purchase one through JBS Technologies, but make sure Should you need help. First check our website at www.bulldogse- curity.com or call our toll-free Tech Support Hotline at: they program all keys to the vehicle since learning just 800-878-8007. -
Page 7: Precautions
SATURN PRECAUTIONS This system is designed for use with vehicles equipped with fuel- injected, gasoline engines and automatic transmissions only. SAFETY FIRST! Never start your vehicle if it is indoors. A periodic safety check is rec- ommended to ensure that your system is in proper working order. DO NOT use mechanical wiring connections, such as crimp or snap together taps. -
Page 8: Using Your Test Probe
PRECAUTIONS SATURN Cut the PINK wire in half and connect as shown. If your vehicle is equipped with air bags or a supplemental restraint systems (SRS) and you CAN NOT identify the air bag wires, STOP THE Turn all Dip Switches OFF. INSTALLATION IMMEDIATELY and have a professional identify the air bag wires before continuing the installation. - Page 9 PASSLOCK II MAKING WIRING CONNECTIONS Strip back one inch of insulation on the wire you need to connect to. Separate the vehicle wire(s) as shown. Make the separation large enough to fit the other wire through. Insert the wire(s) from the starter through the hole as shown. If two or more wires are inserted, wrap them in opposite directions.
- Page 10 MAKING END TO END CONNECTIONS PASSLOCK II With the probes held firmly – dial-in the final resis- Use this method ONLY when connecting two separate wires end to end. tance value needed for your system by turning the When tying two separate wires together at their ends, strip back screw on the variable resistor on the side of the unit 1”...
-
Page 11: Components
PASSLOCK II COMPONENTS Turn the key to the “Run” position and place the • 1 - Main Control Model • 1 - 9-Pin harness vehicle in Reverse. • 1 - 4-button 2-way LCD • 1 - 4-Pin Antenna Harness Remote Transmitters •... - Page 12 WIRING HARNESSES PASSLOCK I Keep all wiring away from moving engine parts, exhaust pipes and high tension cable. Tape wires that pass through holes on the firewall to prevent fraying. Watch out for sharp edges that may damage wires and cause short circuits.
-
Page 13: H1: 6-Pin Heavy Gauge Wiring Connections
PASSLOCK I WIRING CONNECTIONS connector (between the Heavy Gauge RED and H1: 6-PIN HEAVY GAUGE WIRING CONNECTIONS: Remember that the system duplicates the functions of the ignition key RED/WHITE wires), in the main Ignition Switch switch! Below, we will explain the three basic functions of the ignition Harness. -
Page 14: H1/2-3 Red Wire - +12V Power Input
WIRING CONNECTIONS PASSLOCK I H1/2, H1/3 - Red wires - +12V Power Input - Cut the YELLOW wire in half and strip back both Remove the (2) 20A fuses prior to connecting these wires and do ends. Remove some of the insulation on the BLACK not replace them until the satellite has been plugged into the control wire without cutting the wire and the WHITE wire is module. -
Page 15: H2: 5-Pin Wire Harness
VATS WIRING CONNECTIONS H2: 5-PIN WIRE HARNESS: H2/1 – RED/WHITE wire – Parking Light Relay Power Input – The RED/WHITE wire is the input to the flashing parking light relay. The connection of the RED/WHITE wire will determine the Output Polarity on the flashing parking light relay wire WHITE. -
Page 16: H4 - 9-Pin Black Wire Harness
WIRING CONNECTIONS VATS WHITE or (1) WHITE/BLACK striped and - Route the black connector wire behind the trim and connect to the (1)PURPLE/BLACK striped) 20 Gauge wires, two-way transceiver/antenna. - Connect the other end to the control module. these wires are often in a ORANGE or BLACK Plas- - Special considerations must be made for windshield glass as some tic Tube. -
Page 17: H4/2 Thin Black Wire - (-) Neutral Safety Switch Or
VATS WIRING CONNECTIONS H4/2 - Thin Black wire - (-) Neutral Safety Switch or (-) Measure the resistance of the little Pellet on the Remote Toggle Switch Input - Ignition Key. It should be between 392 Ohms and When the THIN BLACK wire is grounded, the remote start unit is oper- 11,800 Ohms. -
Page 18: H4/5 Red/White Wire - (-) 200Ma Channel 3 Trunk Output
WIRING CONNECTIONS USE THIS CHART FOR VATS, PASSLOCK I & PASSLOCK II 1 - 8-Pin Harness Dip Switch # Resistor Value 0.825 1.65 3.32 6.65 13.3 Final Resistance (k ohms) 0.000 +Trimpot Value 0.825 +Trimpot Value 1.650 +Trimpot Value 2.475 +Trimpot Value 3.320 +Trimpot Value 4.145 +Trimpot Value 4.970 +Trimpot Value... -
Page 19: H4/7 Black/White Wire-(-)200Ma Dome Light Supervision Output
WIRING CONNECTIONS LIST OF VEHICLES AND TYPES OF SECURITY SYSTEMS Dodge 300 M 99+ Transponder Pontiac Sunfire 2000 Passlock II H4/7 - BLACK/WHITE wire - (-) 200mA Dome Light Supervision Dodge Intrepid 98+ Transponder Porsche (all 97+) Transponder Output Dodge Neon 2000 Transponder Saab (all 97+) Transponder... -
Page 20: H4/9 Blue/Black Wire - (-) 200Ma Security Bypass Output
WIRING CONNECTIONS LIST OF VEHICLES AND TYPES OF SECURITY SYSTEMS Factory Security Disarm Signal Output - Acura 3.2TL 98+ Transponder GMC suburban 98+ Passlock II Acura RL 98+ Transponder GMC Sonoma 98+ Passlock II This wire is designed to disarm a factory installed security system. Audi A4, A6,A8 98+ Transponder GMC Sierra... -
Page 21: H5 6-Pin Door Lock Connections
MODEL IF114 WIRING CONNECTIONS VATS/PASSLOCK/TRANSPONDER H5 6-Pin Door Lock Connector: UNIVERSAL ALARM BYPASS MODULE This module lets you bypass virtually any type of Vehicle Anti-Theft System on the market today to remotely start your vehicle without permanently disabling the Vehicle’s Factory Anti-Theft System. In 1985, General Motors came out with their first Vehicle Anti-Theft System known as VATS that uses a Resis- tor Pellet in the key. - Page 22 WIRING CONNECTIONS LCD REMOTE CONTROL TRANSCEIVER VACUUM OPER- THE REMOTE LCD ICON DESCRIPTION CHART: ATED DOOR LOCKING Door Lock Door Unlock SYSTEM: TYPICAL OF Your vehicle doors Your vehicle doors are MERCEDES BENZ AND are locked. unlocked AUDI. Locate the wire under Remote In-Range Indicator the driver’s kick panel.
-
Page 23: H6 2-Pin Blue Connector For The Program Switch
OPERATION WIRING CONNECTIONS G. DISABLING THE REMOTE START SYSTEM: (If installed) H6/2-PIN BLUE CONNECTOR FOR THE PROGRAM SWITCH This feature allows your system’s remote start unit to be temporarily dis- Select a mounting location for the switch that is easily accessible to the abled to prevent the vehicle from being remote started accidentally. -
Page 24: Programming
PROGRAMMING OPERATION ALARM FEATURE. #1 PROGRAMMING: Rapidly depresses the button. The parking light will flash (3) Turn the Ignition switch from “ON” to “OFF” (3) times and leave in times. The siren or horn chirps (3) times. The vehicle is now pro- the “OFF”... -
Page 25: Feature Ii Programming
OPERATION PROGRAMMING Note: The Remote Start Unit will not start the vehicle if any one of the FEATURE ‘II” PRORAMMING: following conditions exists: Turn the Ignition switch “ON/OFF” (3) TIMES and leave in the The hood is opened. “OFF” position. The brake pedal is pressed. -
Page 26: Feature Iii Programming
PROGRAMMING OPERATION FEATURE #III PROGRAMMING J. VIBRATION/MELODY MODE: Turn the ignition switch “ON/OFF” (3) TIMES and leave in the It is useful when you are in a noisy place. The remote control “OFF” position. in this mode, vibrates it if your security system is triggered. Push the Program switch (6) times and hold in on the 6th push Press button first, within (5) seconds, press the... -
Page 27: Feature Iv Programming
OPERATION PROGRAMMING D. CAR LOCATOR FEATURE ‘IV” PROGRAMMING: Press the button twice to active car locator function. The horn will Turn the Ignition ‘switch “ON/OFF” (3) TIMES and leave in the chirp (6) times. The parking light will flash (12) times, for you to easily “OFF”... -
Page 28: Check Level Programming
PROGRAMMING OPERATION Within (10) seconds, start the vehicle with the key. (While the en- A. REMOTE TRANSMITTER OPERATION: gine is running, the parking lights and LED will flash, lf they are not Transmitter flashing please check VIOLET/WHITE, wire connection. Button System Function or Feature Remark Press and hold the Program switch for (2) seconds until a long chirp... -
Page 29: Start Timer Programming
IMPORTANT OWNER’S NOTICE PROGRAMMING WARNINGS: START TIMER PROGRAMMING: (TEST and ADJUST) Press the button twice on the transmitter to start the vehicle. As with any product that performs automatic functions, there are certain If everything goes well: Wait for 15 seconds: safety precautions that you must practice and be aware of. -
Page 30: Shutdown Diagnostics
PROGRAMMING TESTING YOUR INSTALLATION Press and hold the buttons at the same time on the trans- Note: A second IN4003 series diode may be required to maintain the mitter for 5 seconds, there will be a confirmation of (6) chirps with integrity of the hood open, shut down circuit. -
Page 31: Caution
TESTING YOUR INSTALLATION TESTING YOUR INSTALLATION Method 2 will allow the safety required for the remote start unit and TESTING YOUR INSTALLATION: prevent the vehicle from starting while in any gear other than Park or Caution!! The follow procedure must be performed after the installa- Neutral while the key is in the ignition cylinder however, the original fac- tion of the Remote Start Device. -
Page 32: Mechanical Neutral Safety Switch Considerations
TESTING YOUR INSTALLATION TESTING YOUR INSTALLATION MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERATIONS: NOTE: I f the optional remote starter enable toggle switch is installed, Mechanical neutral safety switch configurations differ slightly in that they connect the one side of the switch to this reference wire the other do not offer the same level of safety when installing a remote start de- side of to the THIN BLACK Neutral Safety Switch wire (H4/2) of the vice.
Need help?
Do you have a question about the DELUXE 200B and is the answer not in the manual?
Questions and answers