Table of Contents
Advertisement
Quick Links
INSTALLATION GUIDE
CONTENTS
System Features ...........................................
System Components ...........................................
Technical Assistance ........................................
Before You Begin ............................................
Precautions ...............................................
Locating & Making Connections .............................. 4-6
Optional Connections ........................................
Wiring Diagram ..............................................
How to use Your Remote Transmitter ........................... 8
Operating Instructions ................................... 9-10
All tech personnel are expertly qualified to answer any technical questions.
Technicians are available Monday through Friday from 9:00 a.m. until 8:00 p.m. and Saturday 10:00 a.m. until 4:00 p.m.
OWNER'S GUIDE
SECURITY SYSTEM
PRO-SERIES 6002
Technical Assistance
Address
288 Canton Avenue • Wintersville, Ohio 43953
Telephone
Phone: 740-264-4710 • 800-878-8007 • Fax: 740-264-7306
•
1-2
2
2
2
2-3
3-4
7
8
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Bulldog Security PRO_SERIES 6002
Summary of Contents for Bulldog Security PRO_SERIES 6002
-
Page 1: Table Of Contents
INSTALLATION GUIDE • OWNER’S GUIDE SECURITY SYSTEM PRO-SERIES 6002 CONTENTS System Features ........... System Components ........... Technical Assistance ........Before You Begin ..........Precautions ..........Making Connections ........Locating & Making Connections ......4-6 Optional Connections ........Wiring Diagram ..........How to use Your Remote Transmitter ...... -
Page 2: System Features
SYSTEM FEATURES 2 Long Range Four-Button Remotes Hand-held, easy to use and lets you operate the system from an extended distance. Keyless Entry with onboard relays Two onboard relays are provided to work any vehicle’s door locks without additional parts. This feature will remotely lock or unlock your power door locks even if the engine is running or the alarm is in valet mode. -
Page 3: System Components
Ignition Detection Adds protection by sounding the siren and flashing the lights if the ignition wire is hot- wired or turned on when the system is armed, even if the current sensor or door switch wires have been cut. Computer Controlled Fan No additional wiring needed. -
Page 4: Making Wiring Connections
airbag. Doing so may cause a warning light to be displayed which may require a trip to the dealer to be corrected. DO NOT leave the interior or exterior lights on for an extended period of time as it may cause battery drain. -
Page 5: Locating & Making Connections
CAUTION: All wires must be wrapped with tape and wire tied. MAKING END TO END CONNECTIONS Use this method ONLY when connecting two separate wires end to end. 1. When tying two separate wires together at their ends, strip back one inch of insulation on both wires and separate the strands of wire as shown below. - Page 6 4.Connect the siren's BLACK wire to the third mounting screw, using the spade connector. Make sure this is a solid ground. 5.Connect the siren's RED wire to the module's GREY wire. FINDING CONSTANT AND IGNITION POWER Your system requires 12 volts constant and ignition 12 volt that is only on when the ignition is on. 1.There is usually a large gauge wire going to your ignition switch.
- Page 7 INSTALLING THE FLASHING LED STATUS INDICATOR The LED indicator installs inside your vehicle and should be installed as high as possible and be visible from all windows. Drill a 1/4" mounting hole in the dash panel or use the supplied mounting bracket. CONNECTING THE LED STATUS INDICATOR BLUE PLUG Insert the blue plug of the LED status indicator into the...
-
Page 8: Optional Connections
OPTIONAL CONNECTIONS TESTING: Door Locks There are three basic types: “Type A” Door Lock Test (Most GMs and some Chryslers) Probe both of your door lock wires going to the door lock switch usually located in the driver’s kick panel. Probe the lock and the unlock wires, the test probe will show a (-) negative and the GREEN light will glow bright on both the lock and the unlock wires. -
Page 9: Wiring Diagram
WIRING DIAGRAMS HOW TO USE YOUR REMOTE TRANSMITTER FIGURE 1 1. Red (+) 12 Volt Constant 5-Pin BUTTON #1 BUTTON #1 Door Lock ARM/DISARM ARM/DISARM Harness 2. Black Chassis Ground Connector BUTTON #2 BUTTON #2 BLACK 3. Grey (+) Siren Output OPTION #2 OPTION #2 4. -
Page 10: Operating Instructions
OPERATING INSTRUCTIONS LED Status Indicator The LED (red light) provides valuable information about the system and is also a theft deterrent. LED Status LED Display Armed Flashing Slow Disarmed Passive Arming Flashing Fast (arming count down) Valet Constantly On Violated Zone Triggered Device # of Flashes Zone 2... - Page 11 Lock/Unlock with Ignition On Disarm the system and press and hold Button #3 for (10) ten seconds or until the unit chirps once. Release Button #3 then press and release Button #2 within (2) two seconds. The unit will chirp once indicating that the unit is programmed to Lock/Unlock the doors with Ignition.
Need help?
Do you have a question about the PRO_SERIES 6002 and is the answer not in the manual?
Questions and answers