1. Manuals
  2. Brands
  3. Bulldog Security Manuals
  4. Security System
  5. PRO-SERIES 5002
  6. Installation and owner's manual

Bulldog Security PRO-SERIES 5002 Installation And Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

INSTALLATION GUIDE

CONTENTS
System Features ...........................................
System Components ...........................................
Technical Assistance ........................................
Before You Begin ............................................
Precautions ...............................................
Locating & Making Connections .............................. 4-6
Optional Connections ...................................... 6-7
Wiring Diagram ..............................................
How to use Your Remote Transmitter ........................... 8
Operating Instructions ................................... 8-10
All tech personnel are expertly qualified to answer any technical questions.
Technicians are available Monday through Friday from 9:00 a.m. until 8:00 p.m. and Saturday 10:00 a.m. until 4:00 p.m.
OWNER'S GUIDE

SECURITY SYSTEM

PRO-SERIES 5002
Technical Assistance
Address
288 Canton Avenue • Wintersville, Ohio 43953
Telephone
Phone: 740-264-4710 • 800-878-8007 • Fax: 740-264-7306
•
1-2
2
2
2
2-3
3-4
7

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PRO-SERIES 5002 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Bulldog Security PRO-SERIES 5002

Summary of Contents for Bulldog Security PRO-SERIES 5002

  • Page 1: Table Of Contents

    INSTALLATION GUIDE • OWNER’S GUIDE SECURITY SYSTEM PRO-SERIES 5002 CONTENTS System Features ........... System Components ........... Technical Assistance ........Before You Begin ..........Precautions ..........Making Connections ........Locating & Making Connections ......4-6 Optional Connections ........6-7 Wiring Diagram ..........How to use Your Remote Transmitter ......

  • Page 2: System Features

    SYSTEM FEATURES 2 Long Range Four-Button Remotes Hand-held, easy to use and lets you operate the system from an extended distance. Keyless Entry with onboard relays Two onboard relays are provided to work any vehicle’s door locks without additional parts. This feature will remotely lock or unlock your power door locks even if the engine is running or the alarm is in valet mode.

  • Page 3: System Components

    SYSTEM COMPONENTS 1- Installation and Operation Guide 1- 5-Pin Door Lock Harness 1- Main Control Module 1- Momentary Switch 2- Four Button Remote Transmitters 1- LED Status Indicator and Bracket 1- 126db Six Tone Siren 1- Warranty 1- 16-Pin Wire Harness 2- Bulldog Window Decals TECHNICAL ASSISTANCE Should you need help.

  • Page 4: Making Wiring Connections

    1. Except for the LED Status Indicator, NEVER mount components in view or where they can be easily disconnected. 2. Disconnect the dome light fuse until you are ready for final testing. 3. Mount the siren as far away from sources of heat (exhaust manifold, turbo charger, etc.) as possible. Tape, wrap or tube all wires.

  • Page 5: Locating & Making Connections

    2. Twist upper wires together, twist lower wires together as shown. 3. Lay upper twisted pair of wires over right wire as shown. Bring lower twisted pair of wires up to meet the left wire as shown. 4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection. Secure with wire ties as shown.
  • Page 6 CONNECTING THE STARTER IMMOBILIZER Locate the cranking wire in the ignition switch harness. The cranking wire will show 12 volt only when the key is in the cranking position. Cut the wire in two. Try to crank the engine, it should not crank.

  • Page 7: Optional Connections

    1.Drill a 5/16" hole in the mounting surface, taking care not to damage anything behind the surface. 2.Remove the switch's top nut and lock washer. 3.Push the switch into the hole from the back of the mounting surface. Then secure it with the lock washer and nut.

  • Page 8: Wiring Diagram

    button and this wire should again glow both GREEN and RED (dimly). Now press and hold the unlock button on the switch and test the unlock wire. The correct wire will test (-) negative and the GREEN light will glow bright. Release the unlock button and this wire should again glow both GREEN and RED (dimly). Your vehicle has a “Type B”...

  • Page 9: How To Use Your Remote Transmitter

    HOW TO USE YOUR REMOTE TRANSMITTER BUTTON #1 BUTTON #1 ARM/DISARM ARM/DISARM BUTTON #2 BUTTON #2 OPTION #2 OPTION #2 BUTTON #3 BUTTON #3 OPTION #3 OPTION #3 BULLDOG BULLDOG BUTTON #4 BUTTON #4 PANIC PANIC Arming Press Button #1 to arm the system. The siren will chirp 1 time, the lights will flash once, the power door locks will lock (if installed), and the LED will flash slowly indicating the alarm is now armed.
  • Page 10 Automatic Passive Arming To program Automatic Passive Arming On, disarm the system, press and hold Button #3 for 10 seconds, until the unit chirps once. Release Button #3 then press and release Button #3 again within (2) two seconds. The system will chirp once again to indicate that Passive Arming is now programmed ON.
  • Page 11 Dual Lock/Unlock Pulse Off Disarm the system, press and hold Button #3 for 10 seconds or until the unit chirps once. Release Button #3, press and release Button #4 within (2) two seconds, the unit will chirp (4) four times. The unit is now programmed for Dual Lock/Unlock Pulse Off.

Table of Contents