Bosch TDA3605GB Operating Instructions

Solving Minor Problems Yourself
Problem Possible Causes
Iron does not Temperature control (J) on a
work or is not very low setting
heating up
Connection problems
The automatic shut-off system
(*) has been activated
Iron is not There is no water in the tank
steaming
The steam regulator (C) is in the
«0» position
Scale obstruction of internal
components
Water is dripping Temperature control (J) setting
from the holes in is too low
the soleplate
You have pressed the shot of
steam button (A) repeatedly
without waiting for 5 seconds
between each press
Water has been left in the tank
(G) when the soleplate was
cold, with the steam regulator
(C) set at «1» or «2»
Tap or part distilled water has
not been used (see "Filling the
water tank" section) or other
products such as fragrant water
have been added to the tank
Deposits come Traces of lime scale are coming
out through out of the steam chamber
the holes in the
soleplate
Spray does not No water in the tank.
work
Obstructed mechanism.
The iron begins During first use: Certain
to smoke when components on the appliance
switched on. have been lightly greased at the
factory and may produce a little
smoke when initially heated.
Flashing lamp on Auto-shut off has been
top of handle (*) activated.
(*) Model dependent
You can download this manual from the local homepages of Bosch
Thank you for buying the TDA36 steam iron from Bosch. This iron
has a lightweight design and is built to perform
These instructions contain valuable information about the unique
features of this iron and some hints to make ironing easier for you.
Please visit www.bosch-home.co.uk for more product
information or to register your product, just follow the link
to the Online guarantee registration.
Before using the Iron for the first time
Please carry out the following steps:
1. Remove the protective cover from the soleplate before using the iron.
2. While the iron is unplugged, fill the water tank (G) with tap water
3. Plug the appliance into the mains and set the temperature control
(J) to the "max" position by lining it up with the pointer (I).
4. When the iron has reached the correct temperature (the pilot
lamp K goes out), set the steam regulator (C) to the «2» position
by lining it up with the pointer (D).
5. Hold the iron horizontally and repeatedly press the shot of steam
button (A). Any residue should come out of the soleplate (H).
It may smoke and smell – this is normal and will cease after a
short while.
6. If necessary, carefully clean the soleplate down with a dry, folded cloth.
Cleaning and Maintenance
Attention ! Risk of burns !
For general cleaning, follow the information below:
Problem Solution
Dirty/lightly marked iron Clean the body of iron or soleplate with a damp
body or soleplate cloth then dry it.
Mark develops on Set the iron to its maximum temperature setting.
soleplate during use Rub the iron a few times over with a dry cotton cloth
folded several times.
Heavily stained While the iron is cold, iron a linen cloth soaked in
soleplate white vinegar. Then dampen a cloth with water and
wipe the soleplate clean and dry thoroughly.
DO NOT de-scale or clean the water tank with cleaning products
or solvents, as these could cause the iron to drip when using the
steam function.
DO NOT use a "professional steam cleaner" for cleaning the
appliance.
DO NOT use sharp objects or abrasive products to clean the soleplate
or any other part of the appliance. To keep the soleplate in good
condition, do not allow it to come into contact with metal objects.
Solution
Turn the temperature
control to the desired
position
Check that the plug is
inserted into the mains
socket correctly
Move the iron gently from
side to side to re-start it
Fill the water tank
Set the steam regulator
to the relevant position
Remove the steam
regulator (C) and clean
it. If this does not help
contact an Authorised
Technical Service Centre
Set the temperature
control within the steam
area (between the "••"
and "max") or turn the
steam regulator (C) to «0»
Wait 5 seconds between
each press of the jet of
steam button
Always empty the tank
after ironing and set the
steam regulator to «0»
after ironing and when
filling the tank
Mix distilled water with
tap water as directed
in the "Filling the water
tank" section and never
add any other products
to the water tank
Carry out a cleaning
cycle (see Multiple de-
scaling system section)
Add water to the water
tank.
Contact an Authorised
Technical Service Centre.
This is completely normal
and will stop after a short
while.
Move the iron gently
fromside to side to re-
start it. The lamp (O) will
then flash once before it
re-heats
GUARANTEE TERMS
The terms of the guarantee for this appliance are in accordance
with that stated by our representative for the country in which it is
sold. Details of those conditions can be obtained from the retailer
from whom the appliance was purchased. The SALES RECEIPT
must be presented when making any claims against the terms of
this guarantee. We reserve the right to make technical modifications.
Environmental Care
This iron has been designed according to ecological criteria,
related to the sustainable development, analysing its whole
lifecycle - from material selection to its later reuse or recycling
- evaluating the improvement possibilities, from a technical,
economical and environmental point of view.
Before throwing a used appliance away, you should make it
noticeably inoperable e.g. cut off the mains lead and be certain
to dispose of it in accordance with current laws and regulations.
Your retailer, town council or local council can give you detailed
information about these.
This appliance is labelled in accordance with
European Directive 2002/96/EG concerning used
electrical and electronic appliances (waste
electrical and electronic equipment - WEEE).
The guideline determines the framework for
the return and recycling of used appliances as applicable
throughout the EU.
Important
This appliance has been designed exclusively for domestic
use and must not be used for industrial purposes.
Carefully read through the operating instructions for the
appliance and safeguard them for future reference.

General safety instructions

• The iron must not be left unattended while it is
connected to the supply mains.
• Remove the plug from the socket before filling the
appliance with water or before pouring out the
remaining water after use.
• The appliance must be used and placed on a stable
surface.
• When placed on its stand, make sure that the surface
on which the stand is placed is stable.
Customer Service
Great Britain
Bosch Customer Service
Grand Union House
Old Wolverton Road
Milton Keynes
MK12 5PT
UK +44 (0)844 892 8923
IRL +353 (0)1450 2655
www.bosch-home.co.uk
003 TDA36..GB/07/12
TDA 36..
sensixx B2
Operating instructions
• The iron should not be used if it has been dropped,
if there are visible signs of damage or if it is leaking
water. It must be checked by an authorized Technical
Service Centre before it can be used again.
• With the aim of avoiding dangerous situations, any
work or repair that the appliance may need, e.g.
replacing a faulty mains cable, must only be carried
out by qualified personnel from an Authorised
Technical Service Centre.
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children
shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without
supervision.
• Keep the iron and its cord out of reach of children less
than 8 years of age when it is energized or cooling
down.
• This appliance is to be connected and used in accordance with
the information stated on its characteristics plate.
• This appliance must be connected to an earthed socket. If it is
absolutely necessary to use an extension cable, make sure that
it is suitable for 16A and has a socket with an earth connection.
• If the safety fuse fitted in the appliance blows, the appliance
will be rendered inoperative. To restore normal operation the
appliance will have to be taken to an authorised Technical
Service Centre.
• In order to avoid that, under unfavourable mains conditions,
phenomena like transient voltage drops or lighting fluctuations
can happen, it is recommended that the iron is connected to a
power supply system with a maximum impedance of 0.27Ω . If
necessary, the user can ask the public power supply company
for the system impedance at the interface point.
• The appliance must never be placed directly under the tap to
fill the water tank.
• Unplug the appliance from the mains supply after each use, or
if a fault is suspected.
• The electrical plug must not be removed from the socket by
pulling the cable.
• Never immerse the iron in water or any other fluid.
• Do not leave the appliance exposed to weather conditions (rain,
sun, frost, etc.)