1. Manuals
  2. Brands
  3. Black Widow Security Manuals
  4. Remote Starter
  5. 200
  6. Installation manual

Black Widow Security BW RAS 200 Installation Manual

Remote auto start for keyless entry and add-on remote start modules
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
REMOTE AUTO START
FOR KEYLESS ENTRY AND ADD-ON REMOTE START MODULES
INSTALLATION MANUAL
BEFORE INSTALLING THIS PRODUCT PLEASE READ
THIS INSTALLATION MANUAL THOROUGHLY!!
This remote start product is intended for installa-
tion on vehicles equipped with automatic transmis-
sions and electronic fuel injection only!
DO NOT INSTALL THIS UNIT INTO A MANUAL
TRANSMISSION VEHICLE AS IT COULD RESULT IN
SERIOUS INJURY OR DEATH.
• This product must be installed by qualified per-
sonnel according to these instructions and
observing all safety features.
• The system should be placed into the valet
mode when parked inside a garage or being left for
service.
• Always notify service personnel that the vehi-
cle is equipped with a Remote Starter.
• Only start the vehicle in a well ventilated area.
Do not use in a closed garage or indoors.
ITEMS INCLUDED:
• Main unit
• Remote transmitter(s)*
• Plug In LED
• Plug in program switch
• Harness kit with 2 heavy duty fuse holders
• Hood pinswitch
• Extended range receiver module*
• Owner's manual
*S models are provided with single transmitter only.
Add-on modules do not include transmitters.
OPTIONAL ACCESSORIES:
• VAC-10 Vacuum Switch Kit
• APP-1 Universal OEM transponder bypass kit
• APV-1 GM VATS, Passlock I&II bypass kit
• PDLM-3 Power door lock relay module
Before you begin the installation:
• Verify that the vehicle is equipped with elec-
tronic fuel injection.
• Verify that the vehicle is equipped with an auto-
matic transmission.
• Check to see if the vehicle is equipped with any
type of factory security system.
• Check to see if there is a pinswitch for the
hood, if not one must be installed.
• Verify that the vehicle starts and idles proper-
ly before you start the installation.
• Verify with the customer the desired location
for the program switch and LED.
• Always use a multimeter when verifying vehi-
cle wiring.
Remote Start Installation Notes:
The remote start unit senses the vehicle's success-
ful start using one of the following methods:
1. Current sense
2. Tachometer sense
3. Spark or coil wire sense
4. Using optional vacuum switch.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BW RAS 200 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Black Widow Security BW RAS 200

Summary of Contents for Black Widow Security BW RAS 200

  • Page 1 REMOTE AUTO START FOR KEYLESS ENTRY AND ADD-ON REMOTE START MODULES INSTALLATION MANUAL BEFORE INSTALLING THIS PRODUCT PLEASE READ THIS INSTALLATION MANUAL THOROUGHLY!! This remote start product is intended for installa- OPTIONAL ACCESSORIES: tion on vehicles equipped with automatic transmis- •...
  • Page 2 If the Current Sense feature of the remote start provides +12V output to heater and/or air condi- unit does not allow proper operation, the tach tioning system. Some cars may have more than one sense/spark sense wire may be used, or an option- accessory wire.

  • Page 3: Plug In Connectors

    • GRAY WIRE - Ground When Running Output (-). 3-Pin Red Connector: Plug-in connector port for Connect to a relay for starter anti-grind protection. optional features harness. (See installation diagrams). The GRAY wire pro- • GREEN/BLACK WIRE - 3rd channel output (-). vides ground for starter anti-grind protection and Connect to a relay for optional trunk release etc.

  • Page 4: Programmable Features

    equal to the feature you wish to change. The Program #6: Lock Before & After Engine Crank On = Lock when remote start activates LED and parking lights will flash each time the Off = Disabled switch is pushed. (Example: to program feature #3 Default Reset press the program switch 3 times).
  • Page 5 Valet Mode the fuel system unless a properly coded key is When the Valet mode is activated, the vehicle will inserted into the ignition cylinder. To integrate a not start using the remote, but keyless entry func- remote starter into these vehicles, you must deter- tions will still operate.
  • Page 6 SECURITY/REMOTE START WIRING DIAGRAM GREEN DOOR LOCK OUTPUT (-) +12V CONSTANT OUTPUT BLUE DOOR UNLOCK OUTPUT (-) YELLOW VACUUM SWITCH INPUT FACTORY DISARM OUTPUT (-) GREEN/BLACK TRUNK OUTPUT (-) SWITCH WHITE PARKING LIGHT OUTPUT (+) +12V INPUT BROWN ALARM SENSOR INPUT BLACK GROUND INPUT ORANGE...

  • Page 7: Remote Start Troubleshooting

    REMOTE START TROUBLESHOOTING Problem Probable Cause Suggested Correction Unit will not operate. All power inputs are not con- Main Inputs heavy gage red nected to +12V. wires and red fused wire on main harness must be connect- ed to +12V. Keyless Entry features operate Remote Start in Service Mode Turn ignition key to on position,...

  • Page 8: Power Door Lock Diagrams

    POWER DOOR LOCK DIAGRAMS: This module provides negative door lock outputs. FOR NEGATIVE Positive trigger or reverse polarity installations require PARKING LIGHTS (MOST JAPANESE VEHICLES) two SPDT relays or the PDLM-3 Power Door Lock Relay Module (not included). TO VEHICLE PARKING LIGHT Connect relays as shown in the illustrations provided.

This manual is also suitable for:

200

Table of Contents