Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Owner's Manual
FM SECURITY AND
REMOTE START SYSTEM
INSTALLATION MANUAL
BEFORE INSTALLING THIS PRODUCT PLEASE READ
THIS INSTALLATION MANUAL THOROUGHLY!!
This system is intended for installation on
vehicles equipped with automatic transmissions
and electronic fuel injection only!
DO NOT INSTALL THIS SYSTEM INTO A
MANUAL TRANSMISSION VEHICLE AS IT COULD
RESULT IN SERIOUS INJURY OR DEATH.
• This product must be installed by qualified
personnel according to these instructions and
and observing all safety features.
• The system should be placed into the valet
mode when parked inside a garage or being left
for service.
• Always notify service personnel that the
vehicle is equipped with a Remote Starter.
• Only start the vehicle in a well ventilated
area. Do not use in a closed garage or indoors.
ITEMS SUPPLIED WITH
THE SYSTEM :
• Main unit
• 3-button, LCD remote transmitter(s)*
• Plug In LED
• Plug in program switch
• Harness kit with 2 heavy duty fuse holders
• Hood Pin switch
• Extended range transceiver module
• Dual Stage Electronic Shock sensor
• 120dB 6-tone siren
• Owner's manual
*
One or two transmitters provided depending
on system purchased.
OPTIONAL ACCESSORIES:
• VAC-10 Vacuum Switch Kit
• APP-1 Universal OEM transponder bypass kit
• APV-1 GM VATS, Passlock I&II bypass kit
• PDLM-3 Power door lock relay module
1
Advertisement
Table of Contents
Related Manuals for Black Widow Security BW FM 200
Summary of Contents for Black Widow Security BW FM 200
-
Page 1: Optional Accessories
FM SECURITY AND REMOTE START SYSTEM INSTALLATION MANUAL BEFORE INSTALLING THIS PRODUCT PLEASE READ THIS INSTALLATION MANUAL THOROUGHLY!! This system is intended for installation on ITEMS SUPPLIED WITH THE SYSTEM : vehicles equipped with automatic transmissions and electronic fuel injection only! •... -
Page 2: Before You Begin The Installation
Before you begin the installation: vacuum switch can be installed. The vacuum switch is designed to be placed in line with one of • Verify that the vehicle is equipped with the vehicle’s vacuum hoses and provide a ground electronic fuel injection. output (N/C) until the engine is started. -
Page 3: Main Harness
Main Harness: the vehicle’s tach wire or negative fuel injector wire, and set dip switch #4 to OFF. If the tach • WHITE WIRE - Parking light output (+). wire is not accessible, wrap the GRAY wire Connect to the wire that switches to +12V around a spark plug wire or coil wire several when the parking lights are turned on. -
Page 4: Remote Programmable Features
3-Pin Red Connector: Plug-in connector port 2-Pin Red Connector: Plug-in connector port for LED. Mount LED in an area where it may be for optional features harness. easily seen from either side of the vehicle. • GREEN/BLACK WIRE - 3rd channel output (-). 2-Pin Blue Connector: Plug-in connector port Connect to a relay for optional trunk release etc. -
Page 5: Programmable Features
Remote Programmable Features Program #5: Door Unlock Pulse On = Single To enter program mode: Off = Double 1. Turn ignition to the on position. Program #6: Door Lock Pulse Length 2. Wait 2 seconds. On = 0.7 second door lock/unlock pulse 3. -
Page 6: Default Reset
Default Reset 2. Within 5 seconds, press and hold program switch for approximately 2 To reset all programmable features to their seconds. factory default settings: • The LED will light solid. 1. Turn ignition to the on position. • Parking lights will flash once. 2. - Page 7 Bypassing Factory Theft Deterrent Nissan and others). This system requires use of Systems a tiny passive transmitter housed in the base of the key. This device activates when placed close Many newer vehicles are now factory-equipped to the vehicle’s ignition switch. The starter will with anti-theft systems that use either a resistor usually crank but the fuel system will be disabled, coded key or a passive transponder that disables...
- Page 8 SECURITY/REMOTE START WIRING DIAGRAM BLUE GREEN/BLACK UNLOCK(-) TRUNK OUTPUT (-) +12V FACTORY DISARM OUTPUT (-) YELLOW GREEN VACUUM SWITCH INPUT LOCK(-) WHITE/YELLOW HORN OUT(-) SHOCK RED/BLACK DOME LIGHT (-) SENSOR PLUG RF RECEIVER WHITE PARKING LIGHT OUTPUT (+) +12V INPUT DIP SWITCH SETTINGS BROWN Default settings from...
-
Page 9: Transmitter Operation
FM SECURITY/REMOTE START SYSTEM Transmitter Operation Button Operation ARM/DISARM/PANIC Button - To arm or disarm the UNLOCK O.K. system, press button 1. To activate the panic feature, press LOCK button 1 and hold for three seconds. START Button - To start the vehicle, press and hold button 2 for two seconds. -
Page 10: Remote Start Troubleshooting
REMOTE START TROUBLESHOOTING Problem Probable Cause Suggested Correction Unit will not operate. All power inputs are not Main Inputs (heavy gauge red connected to +12V. wires) and small red wire on main harness must be connected to +12V. Keyless Entry features operate System in Service Mode LED is Turn ignition key to on position, but vehicle will not start. - Page 11 SECURITY SYSTEM TROUBLESHOOTING Problem Probable Cause Suggested Correction Alarm will not go into Code Learning RED or YELLOW wire not connected RED wire should connect directly to Mode. to the correct power source. Code the battery. Connect YELLOW wire to Learning sequence performed too true ignition wire (NOT AT FUSE slowly.
- Page 12 POWER DOOR LOCK RELAY POSITIVE TRIGGER DOOR LOCK CIRCUIT: DIAGRAMS: TO POSITIVE LOCK WIRE TO POSITIVE UNLOCK WIRE The system provides negative door LOCK RELAY UNLOCK RELAY lock outputs. Positive trigger or reverse GREEN WIRE BLUE WIRE polarity installations require two SPDT FROM ALARM FROM ALARM relays or the PDLM-3 Power Door...
Need help?
Do you have a question about the BW FM 200 and is the answer not in the manual?
Questions and answers