Advertisement
Quick Links
INSTALLATION
BEFORE INSTALLING THIS PRODUCT PLEASE READ THIS
INSTALLATION MANUAL THOROUGHLY!!
Before Installing:
• This product must be installed by qualified
personnel according to these instructions and and
observing all safety features.
• Before mounting the product check the possible
locations for the siren, LED and module before you
permanently install them
• Always look before drilling. Make sure you will not
cause damage to vehicle hoses, electrical looms or
physical damage to the vehicle.
• Program the Polarity Jumpers for Parking Lights &
Illuminated Entry Output as described on page(s).
• Check to see if the vehicle is equipped with any type
of factory security system.
• Verify with the customer the desired location for
the program switch and LED.
• Always use a multi-meter when verifying vehicle
wiring.
MANUAL
1
Hardware:
• Main unit
• 2 4-button, Remote transmitters with labeled
buttons for lock, unlock trunk release and option.
• Built-in relay for parking lights with polarity jumper
for +/- output
• Built-in relay for dome light with polarity jumper
for output
• Built-in relay for auxiliary output
• Built-in relay for starter defeat (normally closed)
• Built-in relays for door locks
• Plug-in connector for LED
• Plug-in connector for valet override switch
• Plug-in connector for shock sensor
• Plug-in connector for auxiliary sensor
• Standard siren
• Dual-zone plug-in shock sensor Part Kit:
• Main harness
• Plug-in LED
• Plug-in override switch
• 3-Pin door lock harness
• 2-wire starter defeat lead
• (2) Window stickers
Advertisement
Related Manuals for Black Widow Security BW 6 Relay
Summary of Contents for Black Widow Security BW 6 Relay
- Page 1 INSTALLATION MANUAL BEFORE INSTALLING THIS PRODUCT PLEASE READ THIS INSTALLATION MANUAL THOROUGHLY!! Before Installing: Hardware: • Main unit • This product must be installed by qualified • 2 4-button, Remote transmitters with labeled personnel according to these instructions and and buttons for lock, unlock trunk release and option.
- Page 2 Plug in Connectors: While the system is Armed, the system will trigger if: • The doors are opened. 4-Pin White Connector: Plug-in connector port for • The shock sensor detects an impact to the vehicle. dual stage shock sensor. • The hood or trunk is opened. •...
- Page 3 Full-time Silent Arming / Disarming status LED will stop flashing, and the system will not The system can be programmed to Arm and Disarm passively arm until the next time the key is on for the system with or without chirp confirmation during more than 10 seconds.This feature is useful for turning installation.
- Page 4 Valet Mode Deleting Transmitters (Adding a Remote Transmitters Erasing Other Allows you to temporarily disable the security system Transmitters From the System) when the car is being service or turned over to a All stored transmitter codes are automatically parking attendant. deleted when any new transmitter is coded into the To turn Valet Mode on or off: system.
- Page 5 Default Reset for User Programming mode for that Installer Parameter. Following this procedure will set only the User • The siren will chirp to indicate the setting. Programming Parameters to factory default settings. One chirp = Button 1 1. Enter User Programming. Two chirps = Button 2 2.
- Page 6 SECURITY/NETWORK INTERFACE WIRING DIAGRAM BLUE/WHITE - (—) PASSENGER DOOR UNLOCK GRAY - (—) 2ND CHANNEL (TRUNK) BLACK YELLOW - (—) 4TH CHANNEL BLACK/WHITE - (—) DOME LIGHT RED - (+) POWER BROWN - (+) SIREN OUTPUT VIOLET - (+) DOOR TRIGGER BLACK - (—) GROUND WHITE - (+) PARKING LIGHTS GREEN - (—) DOOR TRIGGER...
-
Page 7: Operation
4-BUTTON SECURITY TRANSMITTER OPERATION UNLOCK/DISARM ARM/LOCK HOLD BUTTONS SILENT ARMING & 2&4 3 SEC. FOR DISARMING 4th CHANNEL HOLD 3 SEC. FOR TRUNK CAR JACK WITH ® IGNITION ON BUTTON OPERATION ARM/LOCK - By pressing this button for 3 seconds for PANIC. UNLOCK/DISARM - By pressing this button for 3 seconds system is disarmed. - Page 8 REVERSE POLARITY (ADDING ACTUATORS): TRUNK RELEASE CIRCUIT DIAGRAM: GROUND GROUND TO TRUNK RELEASE WIRE GREEN WIRE BLUE WIRE FROM ALARM FROM ALARM 12V+ (GREEN BLACK WIRE) LOCK RELAY UNLOCK RELAY 12V+ REVERSE POLARITY USING FACTORY SYSTEMS: LOCK RELAY UNLOCK RELAY HORN HONK DIAGRAM: TO POSITIVE HORN HONK TO NEGATIVE HORN HONK...
Need help?
Do you have a question about the BW 6 Relay and is the answer not in the manual?
Questions and answers