Figure 8. Mounting Configuration Dimensions For "Wc" And "Dc" Models - Seagate ST19171W - Barracuda 9.1 GB Hard Drive Product Manual
Barracuda 9 disc drive
Hide thumbs
Also See for ST19171W - Barracuda 9.1 GB Hard Drive:
- Installation manual (48 pages) ,
- Installation manual (44 pages)
Table of Contents
Advertisement
32
[1]
R
F
D
.050 in. (1.27mm)
minimum clearance
[7] [8]
T
AA
U [6] [7]
[2]
V [10]
J2
[10] W
K
J
[4]
Figure 8.
Mounting configuration dimensions for "WC" and "DC" models
N
P
A
G
E
B
[5]
AA
J6
LED
X [9]
[12]
Y
H
S
Barracuda 9 Product Manual, Rev. C
[3]
C
M
L
Notes:
[1]
Mounting holes three on each side, 6-32 UNC. Max screw length into
side of drive 0.15 in. (3.81 mm). Screw tightening torque 6.0 in-lb
(.675 NM) max with minimum thread engagement of 0.12 in. (3.05 mm).
[2]
Mounting holes four on bottom, 6-32 UNC. Max screw length into
bottom of drive 0.15 in. (3.81 mm). Screw tightening torque 6.0 in-lb
(.675 NM) max with minimum thread engagement of 0.12 in. (3.05 mm).
[3]
Interface connector is flush with the end of drive within 0.020 in.
(.5 mm). The interface connector location may extend beyond HDA
dimension "A" by 0.020 in. (.5 mm).
[4]
Decorative front panel (optional).
[5]
Connector J1 is centered (side to side) on drive within 0.020 in.
(.508 mm).
[6]
Dimension "U" is from bottom rear drive mounting holes center(s) to
the face of the connector at the center of the drive.
[7]
Dimensions "T" and "U" are unique requirements for SCA drives only,
required for conformance with latest ANSI SFF Spec #8337.
[8]
Maximum connector non-perpendicularity to side planes pointed to by AA.
[9]
HDA mounting hole to centerline of Pin 1 of J6. Pin ends on J6 are
nominally flush with end of drive.
[10]
HDA mounting hole to centerline of Pin 1 of J2. Dimensions indicated
are for reference only.
[11]
Dimensions to Pin 1 of each connector are nominal values.
[12]
HDA mounting hole to centerline of LED lens.
Inches
A
5.750
0.010
B
4.000
0.010
C
1.640
0.020
D
0.625
0.020
E
4.000
0.010
F
0.250
0.005
G
2.375
0.010
H
3.750
0.010
J
2.375
0.010
K
1.750
0.020
L
0.181
0.015
M
0.340
0.015
N
0.190
0.010
P
0.015
max
R
1.720
0.010
S
4.100
0.010
T
0.150
U
1.620
0.020
V
0.260
W
0.030
[11]
X
0.405
Y
2.265
Millimeters
146.05
.25
101.60
.25
41.66
.51
15.87
.50
101.60
.25
6.35
.13
60.32
.25
95.25
.25
60.32
.25
44.45
.50
4.60
.38
8.64
.38
4.83
.25
0.381
max
43.69
.25
104.14
.25
0.38
41.15
.50
6.60
0.76
[11]
10.28
57.53
Advertisement
Table of Contents
