Class d series high current series amplifier install kits intake series immortal series sound q series high excursion series low profile series natural sound series abc series component speakers as series conversion speakers tweeters capacitor, bass drive (5 pages)
Page 2
Judge for yourself, and remember what it’s all about, “If it’s not Bigger, Bad- der & Better, it’s not Audiobahn.” If audio is your life, Audiobahn is the brand for you! We make you look as good as you sound. People never stop trying to get the best...
TABLE OF CONTENTS Introduction______________________________________________________ 3 Features and Specifications_________________________________________ 4 Control and Functions_____________________________________________ 5-10 Planning / Mounting Your System____________________________________ Wiring Diagram__________________________________________________ Bridging 2 Amplifiers______________________________________________ 13-14 Adjusting and Tuning______________________________________________ Troubleshooting__________________________________________________ Warning / Disclaimer______________________________________________ Warranty_______________________________________________________ 18-19 Notes__________________________________________________________ 20-22...
Authorized Audiobahn Dealer, as we provide specialized training through our Audiobahn Installer Training Programs. Please read your warranty, keep your receipt, and original carton for possible future use. To get a free brochure on Audiobahn products in the US call (714) 452-1476 or e-mail us at sales@audiobahn.com. WARNING Continuous exposure to sound pressure levels over 100dB may cause permanent hearing loss.
Page 7
CONTROLS & FUNCTIONS 1. Bass Boost Gain Remote Control This plug connects the amplifier and the remote bass knob using the supplied cable. 2. Input Sensitivity Control This control adjusts the amplifier's input sensitivity. The input sensitivity is variable from 200 Millivolts to 8 volts.
Page 8
CONTROLS & FUNCTIONS 4. Low Level LINE OUT RCA Jacks The LINE OUT allows you to build a multiple amplifier system without having to use splitter cords or Y-adapters to distribute the signal. Now it is simply a matter bringing one set of RCAs into the first amplifier, then using the line out RCA jacks as the feed to the next amplifier.
Page 9
CONTROLS & FUNCTIONS 7. Low-Pass Filter Control For use as a dedicated subwoofer channel, set the filter switch to the "LPF" (Low Pass Frequency). Adjust the variable crossover frequency with control knob as desired. The amplifier input circuit filters out everything above 50Hz ...
Page 10
CONTROLS & FUNCTIONS 11. Speaker Terminals These terminals are used to wire your subwoofer(s) to the amplifier. 12. B- Terminal (Chassis Ground) To avoid unwanted ignition noise caused by ground loops, it is essential that the amplifier be grounded to a clean, bare, metal of the vehicle's chassis.
CONTROLS & FUNCTIONS 14. Remote Turn-on Input The remote terminal needs to be wired to the car's stereo or source unit remote turn on wire. This amplifier is turned on remotely when the vehicle's stereo is turned on. NOTE: iF YOUR RADIO DOES NOT HAVE A +12 VOLT OUTPUT LEAD WHEN THE CAR IS TURNED ON, THE "REMOTE"...
PLANNING/MOUNTING YOUR SYSTEM Planning Your System Before beginning the installation, consider the following: If you plan to expand your system by adding other components sometime in the future, ensure that adequate space is left, and cooling requirements are met. If your radio/source is equipped with Pre-Amp outputs, it is possible to utilize them to drive an Amplifier and connecting (Amplifier) to the 2 rear speakers.
Page 14
Bridged 2 amplifiers IF BRIDGED SWITCH POSITION IS ON SLAVE, ALL CONTROLS ARE NON-FUNCTIONAL. ALL CONTROLS ARE NOW CONTROLLED BY THE MASTER AMPLIFIER.
ADJUSTING AND TUNING Below you will find information on adjusting the amplifiers gains. Adjusting the gain correctly is essential to proper operation of the amplifier. If the gain is not adjusted properly it can and will lead to damage of the amplifier and connected speakers and will void your MANUFACTURER WARRANTY.
TROUBLESHOOTING SYMPTOMS CHECK POINTS CURE NO SOUND Is the power Check fuses in amplifier. LED illuminated ? Be sure Turn-on lead is connected ( NO ) Check signal leads. Check gain control. Check Tuner/Deck volume level. Clean contacts on fuse holders. Is the Diagnostic Check for speaker short or Amplifier overheating.
Using a fuse of a different type or rating may result in damage to this system which is not covered by the warranty. Disclaimer Specifications are subject to change without notice. For the most updated Specifications call Audiobahn, your local Authorized Audiobahn Dealer, or check the Audiobahn web site. www.audiobahn.com...
Because of this we recommend that you have your new products installed by an Au- thorized Audiobahn Dealer. (A list of Authorized Audiobahn Dealers can be found on our web page). Warranty Period: One year from the original date of purchase.
Page 20
Any product found to have a manufacturer defect will be replaced with a new piece of the same or similar model, or repaired at the discretion of Audiobahn. Any product found to have no manufacturer defect will be returned to the sender at their cost.
Page 24
7050 Village Drive, Bldg G Buena Park, CA 90621 714-452-1476 o ce 888-880-8469 fax info@audiobahn.com PROUD SPONSOR OF Follow us on Facebook and Twitter...
Need help?
Do you have a question about the A12001DJ and is the answer not in the manual?
Questions and answers