Enabling/Disabling Remote Control Wireless Transmission; Loop Out Setting; Id Number Setting; Video Wall Setting - NEC PX-61XM3A Operation Manual

Enabling/disabling remote control wireless
transmission
This function enables/disables remote control wireless
transmission.
Example: Setting "OFF"
Set "ADVANCED OSM" to "ON" in the main menu (1/
2), then perform the following operations.
On "IR REMOTE" of "OPTION3" menu, select "OFF", then
press the MENU/ENTER button.
OPTION3
PREVIOUS PAGE
TIMER
PWR. ON MODE
CONTROL LOCK
IR REMOTE
LOOP OUT
ID NUMBER
VIDEO WALL
NEXT PAGE
SEL. ADJ.
Information
IR REMOTE settings
ON: Enables remote control wireless transmission.
OFF: Disables remote control wireless transmission.
Set "OFF" to avoid unwanted control from other remote
controls.

Loop Out setting

When this feature is set to ON, the received signal will be
looped out.
Example: Setting "ON"
Set "ADVANCED OSM" to "ON" in the main menu (1/
2), then perform the following operations.
On "LOOP OUT" of "OPTION3" menu, select "ON".
OPTION3
PREVIOUS PAGE
TIMER
PWR. ON MODE
CONTROL LOCK
IR REMOTE
LOOP OUT
ID NUMBER
VIDEO WALL
NEXT PAGE
SEL. ADJ.
Information
LOOP OUT settings
ON: The received signal will be looped out via PC1
terminal or VIDEO1 terminal.
OFF: The received signal will not loop out.
* Even if LOOP OUT is ON, signals won't be sent out if
POWER is being turned off.
To connect another display...
See page 7.
If the RGB/PC1 signal is present at the time
the power switched on...
The RGB/PC1 input will be displayed regardless of the
setting of LOOP OUT.
3 / 4
: LAST
: OFF
: OFF
: OFF
: ALL
EXIT RETURN
3 / 4
: LAST
: OFF
: ON
: ON
: ALL
EXIT RETURN

ID number setting

When using more than one of these displays, this function
sets ID numbers so that operation of the remote control
does not cause multiple monitors to operate at the same
time.
Example: Setting "2"
Set "ADVANCED OSM" to "ON" in the main menu (1/
2), then perform the following operations.
On "ID NUMBER" of "OPTION3" menu, select "2".
PREVIOUS PAGE
TIMER
PWR. ON MODE
CONTROL LOCK
IR REMOTE
LOOP OUT
ID NUMBER
VIDEO WALL
NEXT PAGE
SEL.
* To reset back to ALL
Press the CLEAR/SEAMLESS SW button.
Information
ID NUMBER settings
ALL: ID NUMBER will not be set.
1 to 256: ID NUMBER will be set.
When the ID NUMBER have been set
You can also set ID NUMBER for each remote control
to operate the plasma display individually. To do so,
see below.
To set the ID number for the remote control
Example: Setting "2"
Press the ID SELECT button on the remote control.
The "ID SELECT" screen appears.
On "ID NUMBER" of "ID SELECT" menu, select "2".
ID NUMBER
* To reset back to ALL
Press the CLEAR/SEAMLESS SW button.

Video Wall setting

When creating a video wall, use a distribution amplifier
(any commercially available distribution amplifier) to
connect the split signals to the respective monitor INPUT
terminals.
Use this feature to configure a 4-25 video wall.
Set "ADVANCED OSM" to "ON" in the main menu (1/
2), then perform the following operations.
On "OPTION3" menu, select "VIDEO WALL", then press
the MENU/ENTER button.
The "VIDEO WALL" screen appears.
DIVIDER
POSITION
DISP. MODE
AUTO ID
IMAGE ADJUST
P. ON DELAY
PLE LINK
REPEAT TIMER
31 SEL.
OPTION3 3 / 4
: LAST
: OFF
: ON
: OFF
: 2
ADJ. EXIT RETURN
ID SELECT
POSITION : 1
: 2
EXIT
ADJ. RETURN
VIDEO WALL
: 1
: SPLIT
: OFF
: OFF
: OFF
: OFF
EXIT
ADJ. RETURN