Table of Contents
Advertisement
Quick Links
IntelliStation A Pro
Type 6217
Installation Guide
Welcome. . .
Thank you for buying an IBM
IntelliStation A Pro computer.
This
Installation Guide
information for setting up,
installing options, and configuring
your computer.
This book also contains
information for every day use,
and solving problems.
You can find the most current
information about your
computer on the IBM Web site at:
http://www.ibm.com/pc/support
contains
System is ready to use.
• Register your computer:
Go to http://www.ibm.com/pc/register/
• Install options and applications
Set up the computer
Start the computer
No
Did the computer
start correctly?
Yes
Do you plan
No
to use Windows XP or
Red Hat Linux ?
Yes
Complete the setup
program
Go to the Computer Support
flow chart
Install another
operating system
Advertisement
Table of Contents
Related Manuals for IBM 62174DU - IntelliStation A - Pro 6217
Summary of Contents for IBM 62174DU - IntelliStation A - Pro 6217
-
Page 1: Installation Guide
Do you plan Install another to use Windows XP or operating system information about your Red Hat Linux ? computer on the IBM Web site at: http://www.ibm.com/pc/support Complete the setup program System is ready to use. • Register your computer: Go to http://www.ibm.com/pc/register/... - Page 2 Check all cables for loose connections and verify that all optional devices you installed are on the compatibility matrix. You can view the compatibility matrix http://www.pc.ibm.com/us/compat/ intellistation/ View information about IBM Support Line at http://www.ibm.com/services/sl/products/ Problem or view support telephone numbers at solved? http://www.ibm.com/planetwide/ View support telephone numbers at http://www.ibm.com/planetwide/...
- Page 3 IntelliStation A Pro Type 6217 Installation Guide...
- Page 4 Before using this information and the product it supports, be sure to read the general information in and Appendix B, “Notices,” on page 73, and the Warranty and Support Information document on the IBM IntelliStation Documentation CD. First Edition (June 2005) ©...
-
Page 5: Table Of Contents
Creating an emergency recovery-repair diskette in Windows ..53 Creating an IBM Enhanced Diagnostics Diskette or CD in Windows ..54 Chapter 5. Solving problems ....57 Diagnostic tools . - Page 6 Diskette drive problems ..... 63 Hard disk drive problems ....63 Keyboard, mouse, or pointing-device problems .
-
Page 7: Safety
Vor der Installation dieses Produkts die Sicherheitshinweise lesen. Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza. Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet. Antes de instalar este produto, leia as Informações sobre Segurança. © Copyright IBM Corp. 2005... - Page 8 Antes de instalar este producto, lea la información de seguridad. Läs säkerhetsinformationen innan du installerar den här produkten. Statement 1: DANGER Electrical current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: v Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm.
- Page 9 Statement 2: CAUTION: When replacing the lithium battery, use only IBM Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer.
- Page 10 Statement 4: ≥ 18 kg (39.7 lb) ≥ 32 kg (70.5 lb) ≥ 55 kg (121.2 lb) CAUTION: Use safe practices when lifting. Statement 5: CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device.
- Page 11 All caution and danger statements in this documentation begin with a number. This number is used to cross reference an English caution or danger statement with translated versions of the caution or danger statement in the IBM Safety Information document.
- Page 12 For example, if a caution statement begins with a number 1, translations for that caution statement appear in the IBM Safety Information document under statement Be sure to read all caution and danger statements in this documentation before performing the instructions. Read any additional safety information that comes with your computer or optional device before you install the device.
-
Page 13: Chapter 1. Introduction
IntelliStation A Pro Type 6217 computer and basic instructions for installing some options. More detailed instructions for installing options are in the User’s Guide on the IBM IntelliStation Documentation CD, which comes with your computer. This document contains information about:... -
Page 14: The Ibm Intellistation Documentation Cd
The IBM IntelliStation Documentation CD The IBM IntelliStation Documentation CD contains documentation for your computer in Portable Document Format (PDF) and includes the IBM Documentation Browser to help you find information quickly. Hardware and software requirements The IBM IntelliStation Documentation CD requires the following minimum hardware and software: v Microsoft Windows NT 4.0 (with Service Pack 3 or later), Windows 98, Windows... -
Page 15: Related Documentation
IBM IntelliStation Documentation CD This CD contains all of the IBM IntelliStation A Pro Type 6217 documents in Portable Document Format (PDF). Depending on your computer model, additional documentation might be included on the IBM IntelliStation Documentation CD. -
Page 16: Notices And Statements In This Document
To check for updated documentation and technical updates, complete the following steps: Note: Changes are made periodically to the IBM Web site. The actual procedure might vary slightly from what is described in this document. 1. Go to http://www.ibm.com/pc/support/. -
Page 17: Features And Specifications
Features and specifications The following table provides a summary of the features and specifications of your IntelliStation A Pro computer. Depending on your model, some features might not be available, or some specifications might not apply. Table 1. Features and specifications Microprocessor: Integrated functions: Heat output:... -
Page 18: Controls, Leds, And Connectors
Controls, LEDs, and connectors This section identifies the controls, LEDs, and front connectors on the IntelliStation A Pro Type 6217 computer. See “Cabling the computer” on page 40 for an illustration of the connectors on the rear of the computer. Ethernet link status LED CD or DVD drive activity LED... - Page 19 Line out connector (green) Use this connector to send audio signals from the computer to external devices, such as speakers with built-in amplifiers, headphones, multimedia keyboards, or the audio line-in jack on a stereo system. USB connectors Use these connectors to connect USB devices to your computer, using redundant Plug and Play technology.
- Page 20 IntelliStation A Pro Type 6217: Installation Guide...
-
Page 21: Chapter 2. Installing The Hardware
This chapter provides instructions for installing or replacing options in your computer. For a list of supported options for your computer, go to http://www.ibm.com/pc/; then, select your country and navigate to the list of options for your computer. For more detailed installation information, see the Problem Determination and Service Guide on the IBM IntelliStation Documentation CD. -
Page 22: Air Circulation
This section provides instructions for installing and replacing hardware options in your computer. These instructions are intended for users who are experienced with setting up IBM computer hardware. If you need more detailed instructions, see the Problem Determination and Serive Guide on the IBM IntelliStation Documentation CD. -
Page 23: System Reliability Considerations
v Have a small flat-blade screwdriver available. v When you need to access the inside of the computer to install options, you might find it easier to lay the computer on its side. v Blue on a component indicates touch points, where you can grip the component to remove it from or install it in the computer, open or close a latch, and so on. -
Page 24: Installing Options In Your Computer
Installing options in your computer This section provides instructions for installing hardware options in your computer. Major components of your computer The following illustration shows the major components in the A Pro Type 6217 computer. Rear adapter- CD-ROM retention bracket drive Memory modules shield... - Page 25 System-board option connectors The following illustration shows the system-board connectors for user-installable options. Microprocessor board for microprocessor 2 Microprocessor 1 (U27) DIMM 1 DIMM 2 DIMM 3 DIMM 4 Battery PCI-X 1 PCI-X 2 PCI-X 3 PCI Express x16 PCI-X 4 PCI-X 5 Chapter 2.
- Page 26 System-board internal connectors The following illustration shows the internal connectors on the system board. Front Ethernet activity LED Front 1394 (FireWire) Diskette SATA 0 Front USB connectors SATA 1 Primary IDE Boot block jumper Power Secondary IDE Front panel Rear system fan 1 Rear system Microprocessor 1 fan...
-
Page 27: Optional Microprocessor Board Connectors
System-board external connectors The following illustration shows the external input/output connectors on the system board. Keyboard/ mouse Serial 2 Parallel Serial 1 USB 1, USB 2, IEEE 1394 Ethernet, USB 3 Audio Optional microprocessor board connectors If you decide to add a second microprocessor to your computer, the microprocessor option kit includes a microprocessor board that you attach to the system board. -
Page 28: Removing The Cover
Removing the cover To remove the computer side cover, you might find it easier to lay the computer on its side. To remove the side cover, complete the following steps: 1. Review the “Installation guidelines” on page 10. 2. Turn off the computer and all attached devices (see “Turning off the computer” on page 42);... -
Page 29: Removing And Installing The Support Bracket
Removing and installing the support bracket When working with some options, such as hard disk drives and memory modules, you must first remove the support bracket to access the option. To remove the support bracket, complete the following steps: 1. Read the safety information beginning on page v and the guidelines in “Handling static-sensitive devices”... -
Page 30: Removing The Bezel
Removing the bezel When working with some devices, such as additional optical drives, you must first remove the bezel to access the device. To remove the bezel, complete following steps: 1. Unlock the side-cover lock. 2. Remove the side cover (see “Removing the cover” on page 16). 3. - Page 31 (SATA), or small computer system interface (SCSI) devices; and then PCI-X slots 2 through 5. v For a list of supported options for your computer, go to http://www.ibm.com/pc/; then, select your country and navigate to the list of options for your computer.
-
Page 32: Cabling An Optional Scsi Adapter
adapter directly from the static-protective package to the adapter slot. Avoid touching the components and gold-edge connectors on the adapter. Attention: Make sure that the adapter is correctly seated in the expansion slot before you turn on the computer. Incomplete installation of an adapter might damage the system board or the adapter. - Page 33 RAID adapter installed, you can configure the internal hard disk drives into disk arrays. You can also cable a SCSI adapter to external hard disk drives. See your SCSI adapter option documentation for complete instructions for installing a SCSI adapter in your computer and for additional information about SCSI adapters. Notes: 1.
-
Page 34: Installing Internal Drives
Installing internal drives Bay 1 Bay 2 Bay 3 Bay 6 Bay 5 Bay 4 The following notes describe the types of drives that your computer supports and other information that you must consider when installing internal drives. v Your IntelliStation A Pro computer comes with an IDE optical drive (CD-ROM, CD-RW, or DVD/CD-RW combo drive) in bay 1 and a hard disk drive in bay 4. - Page 35 For a complete list of supported options for your computer, go to http://www.ibm.com/pc/; then, select your country and navigate to the list of options for your computer. Preinstallation steps: Some of these steps are required only the first time you install a hard disk drive in a specific bay.
- Page 36 Statement 3: CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: v Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device.
- Page 37 Drive clip 11. Push the drive into the bay. 12. Determine whether the drive is an IDE or SCSI device; then, connect one end of the applicable signal cable into the back of the drive and the other end of this cable into the applicable IDE or SCSI connector on the system board.
- Page 38 Installing a drive in bay 3: Note: Only a 3.5-in. device can be installed in bay 3. To install a drive in bay 3, complete the following steps: 1. Follow the instructions in “Preinstallation steps” on page 23. 2. Turn off the computer and all attached devices (see “Turning off the computer” on page 42);...
- Page 39 Statement 3: CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: v Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device.
- Page 40 11. Route the signal cable so that it does not block the airflow to the rear of the drives or over the microprocessor. 12. Connect the power cable to the back of the drive. The connectors are keyed and can be inserted only one way. 13.
- Page 41 10. Slide the drive into the drive bay until the drive snaps into place. 11. Determine whether the drive is a Serial ATA or SCSI device; then, connect one end of the applicable signal cable into the back of the drive and the other end of this cable into the applicable Serial ATA or SCSI connector on the system board.
-
Page 42: Installing Memory Modules
v When you install a drive, set the jumpers either to disable auto-start or to delay startup, to prevent the system power supply from being overtaxed by all drives trying to spin up at once. v The computer has two IDE buses, primary and secondary. Each of these buses supports up to two IDE devices. - Page 43 PC2700 or PC3200 SDRAM registered, buffered DIMM specification. For a list of supported options for your computer, go to http://www.ibm.com/pc/; then, select your country and navigate to the list of options for your computer. v DIMMs must be installed in matched pairs. The DIMMs in each pair must be the same size, speed, type, and technology as each other but do not have to match other pairs.
- Page 44 resources. The BIOS will display the total amount of installed memory and the amount of configured memory. To obtain a full 16 GB or more of usable memory, you must install a second microprocessor and memory. v When you restart the computer after adding or removing DIMMs, the computer displays a message that the memory configuration has changed.
-
Page 45: Installing A Second Microprocessor
DIMM connector 1 DIMM connector 2 DIMM connector 3 DIMM connector 4 12. Repeat steps 8 through 11 for the second DIMM in the pair. 13. If you moved the drive cage out of the way in step 5, push the drive cage outward and press in on the drive-cage release tab. - Page 46 The most current level of BIOS code for the computer is available from http://www.ibm.com/pc/support v For a list of supported microprocessor options for your computer, go to http://www.ibm.com/pc/; then, select your country and navigate to the list of options for your computer Before you begin, obtain the following items:...
- Page 47 Option screws (captive) Microrpocessor Alignment board holes Short screws Press points Alignment pins System board Second-microprocessor connectors 7. Remove the six indicated screws from the system board. 8. Position the alignment holes in the microprocessor board over the two plastic alignment pins on the system board;...
- Page 48 Lever open Attention: You must make sure that the release lever on the microprocessor socket is in the fully open position before you insert the microprocessor in the socket. Failure to do so might result in permanent damage to the microprocessor, microprocessor socket, and system board.
- Page 49 Fan sink Fan sink cable Microprocessor Retention spring clips a. Make sure that the two retention spring clips on the microprocessor retention bracket (on the microprocessor board) are open and rotated to either side as shown in the illustration above. b.
-
Page 50: Installing A Security Rope Clip
Power supply alignment flange Locking Air baffle a. Orient the air baffle as shown and align it with the side of the power supply. b. Insert the small end of the baffle into the computer toward the front of the computer. -
Page 51: Replacing The Bezel
3. Use a screwdriver to remove the two metal knockouts. 4. Insert the rope clip through the rear panel; then, attach and tighten the nuts. 5. Thread the cable through the rope clip and around an object that is not part of or permanently secured to the building structure or foundation, and from which the cable cannot be removed. -
Page 52: Completing The Installation
Replacing the side cover If you removed the support bracket, reinstall it before you replace the side cover. See “Removing and installing the support bracket” on page 17. Note: The rear adapter-retaining bracket rests against the computer side cover. You might find it easier to lay the computer on its side to replace the side cover. To replace the side cover, complete the following steps: 1. -
Page 53: Turning On The Computer
See the User’s Guide on the IBM IntelliStation Documentation CD and the documentation that comes with your monitor for additional information. -
Page 54: Running The Operating System Setup Program
® v When you connect the computer to power for the first time, the Wake on LAN feature can turn on the computer. If the computer was previously turned on, it must be turned off correctly for the Wake on LAN feature to turn on the computer. - Page 55 Statement 5: CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.
- Page 56 IntelliStation A Pro Type 6217: Installation Guide...
-
Page 57: Chapter 3. Installing Software
To view the license agreement in Windows XP, complete the following steps: 1. From the Windows XP desktop, click Start → All Programs → Access IBM. 2. Select IBM License Agreement. For Red Hat Linux, when you start the computer, the License Agreement window opens. -
Page 58: Starting The Configuration/Setup Utility Program
3. Select Save Settings and press Enter. Using the Adaptec HostRAID configuration programs Use the Adaptec RAID Configuration Utility programs and SCSISelect Utility (also referred to as IBM ServeRAID-7e) to add RAID levels 0 and 1 functionality to the IntelliStation A Pro Type 6217: Installation Guide... - Page 59 Adaptec RAID Configuration Utility programs, see the documentation on the IBM ServeRAID-7e (Adaptec HostRAID) Support CD. If this CD did not come with your computer, you can download the IBM ServeRAID-7e (Adaptec HostRAID) Support CD from the IBM Web site at: http://www.ibm.com/pc/support/.
- Page 60 SCSI RAID feature and install the device drivers before you can use it. The SCSI RAID configuration utilities, device drivers, and information are available on the IBM ServeRAID-7e (Adaptec HostRAID) Support CD. If this CD did not come with your computer, you can download the IBM ServeRAID-7e (Adaptec HostRAID) Support CD from the IBM Web site at http://www.ibm.com/pc/support/.
-
Page 61: Using Serveraid Manager
SCSI settings for attached devices. See the documentation on the IBM ServeRAID-7e (Adaptec HostRAID) Support CD for additional information about how to use the SCSI HostRAID feature. Configuring the controller: To use the SCSI HostRAID feature to configure a level-1 RAID array, complete the following steps: 1. -
Page 62: Configuring The Controller
ServeRAID Manager in Startable CD mode. To run the ServeRAID Manager program in startable-CD mode, turn on the computer; then, insert the IBM ServeRAID Support CD into the CD-ROM drive. If the ServeRAID Manager program detects an unconfigured controller and ready drives, the program automatically starts the Configuration wizard. -
Page 63: Viewing The Configuration
For device drivers and information about configuring the Gigabit Ethernet controller, go to http://www.ibm.com/pc/support/. Starting the SCSISelect utility program (some models) To start the SCSISelect utility program, complete the following steps: 1. - Page 64 IntelliStation A Pro Type 6217: Installation Guide...
-
Page 65: Chapter 4. Completing The Installation
Use one of the following methods to register your computer in Windows: v From the Windows XP desktop, click Start → All Programs → IBM Registration and then follow the instructions. If you do not have access to the Internet, you... -
Page 66: Creating An Ibm Enhanced Diagnostics Diskette Or Cd In Windows
You can only create an IBM Enhanced Diagnostics diskette from the Product Recovery program. You can create an IBM Enhanced Diagnostics diskette or CD from the World Wide Web. To create an IBM Enhanced Diagnostics diskette from the Product Recovery program partition, complete the following steps: 1. - Page 67 To create an IBM Enhanced Diagnostics diskette or CD from the World Wide Web, complete the following steps: 1. Go to http://www.ibm.com. 2. Click Support & downloads. 3. Click Search technical support. 4. In the Enter keyword(s) field, type diagnostics 6217, and click Submit.
- Page 68 IntelliStation A Pro Type 6217: Installation Guide...
-
Page 69: Chapter 5. Solving Problems
If you cannot diagnose and correct the problem using the information in this chapter, see Appendix A, “Getting help and technical assistance,” on page 71 and “Solving problems” in the Problem Determination and Service Guide on the IBM IntelliStation Documentation CD. -
Page 70: Power-On Self-Test (Post)
The following table provides an abbreviated list of the POST error codes that might appear during startup. Note: See the Problem Determination and Service Guide on the IBM IntelliStation Documentation CD for more information about the POST error messages. IntelliStation A Pro Type 6217: Installation Guide... - Page 71 Table 2. POST error messages v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, Parts Listing, Machine Type 6217 in the Problem Determination and Service Guide to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
- Page 72 Table 2. POST error messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, Parts Listing, Machine Type 6217 in the Problem Determination and Service Guide to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
- Page 73 Table 2. POST error messages (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, Parts Listing, Machine Type 6217 in the Problem Determination and Service Guide to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
-
Page 74: Troubleshooting Tables
If you cannot find the problem in these tables, see “Starting the diagnostic programs and viewing the test log” in the Problem Determination and Service Guide on the IBM IntelliStation Documentation CD to test the computer. If you have just added new software or a new optional device and the computer is not working, complete the following steps before using the troubleshooting tables: v Remove the software or device that you just added. -
Page 75: Diskette Drive Problems
Diskette drive problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, Parts Listing, Machine Type 6217 in the Problem Determination and Service Guide to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). -
Page 76: Keyboard, Mouse, Or Pointing-Device Problems
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, Parts Listing, Machine Type 6217 in the Problem Determination and Service Guide to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). -
Page 77: Memory Problems
Memory problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, Parts Listing, Machine Type 6217 in the Problem Determination and Service Guide to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). -
Page 78: Monitor Problems
76 mm (3 in.). b. Non-IBM monitor cables might cause unpredictable problems. 2. Replace the following components one at a time, in the order shown, restarting the computer each time: a. -
Page 79: Power Problems
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 3, Parts Listing, Machine Type 6217 in the Problem Determination and Service Guide to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). -
Page 80: System-Board Error Leds
LED will not be lit the next time the computer is restarted; if the problem remains, the LED will be lit again. See “Solving problems” in the Problem Determination and Service Guide on the IBM IntelliStation Documentation CD for additional information. -
Page 81: Microprocessor-Board Error Leds
LED will not be lit the next time the computer is restarted. If the problem remains, the LED will continue to be lit. See “Solving problems” in the Problem Determination and Service Guide on the IBM IntelliStation Documentation CD for additional information. -
Page 82: Product Recovery Program
If your hard disk drive, including the partition that contains the Product Recovery program, becomes damaged or if you replace the hard disk drive, contact IBM to order the IBM Product Recovery CD to recover your preinstalled operating system, application programs, and device drivers.See Appendix A, “Getting help and... -
Page 83: Appendix A. Getting Help And Technical Assistance
If you need help, service, or technical assistance or just want more information about IBM products, you will find a wide variety of sources available from IBM to assist you. This appendix contains information about where to go for additional... -
Page 84: Software Service And Support
You can find service information for your IBM products, including supported options, at http://www.ibm.com/pc/support/. Software service and support Through IBM Support Line, you can get telephone assistance, for a fee, with usage, configuration, and software problems with xSeries servers, IntelliStation workstations, and appliances. For information about which products are supported by Support Line in your country or region, go to http://www.ibm.com/services/sl/products/. -
Page 85: Appendix B. Notices
Web sites. The materials at those Web sites are not part of the materials for this IBM product, and use of those Web sites is at your own risk. IBM may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. -
Page 86: Trademarks
Chipkill ThinkPad EtherJet Tivoli e-business logo Tivoli Enterprise Eserver Update Connector FlashCopy Wake on LAN XA-32 IBM (logo) XA-64 IntelliStation X-Architecture NetBAY XceL4 Netfinity XpandOnDemand NetView xSeries OS/2 WARP Intel, MMX, and Pentium are trademarks of Intel Corporation in the United States, other countries, or both. -
Page 87: Product Recycling And Disposal
IBM makes no representations or warranties with respect to non-IBM products. Support (if any) for the non-IBM products is provided by the third party, not IBM. Some software may differ from its retail version (if available), and may not include user manuals or all program functionality. -
Page 88: Electronic Emission Notices
Consult an IBM authorized dealer or service representative for help. Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Proper cables and connectors are available from IBM authorized dealers. IBM is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment. -
Page 89: Avis De Conformité À La Réglementation D'industrie Canada
Power cords For your safety, IBM provides a power cord with a grounded attachment plug to use with this IBM product. To avoid electrical shock, always use the power cord and plug with a properly grounded outlet. - Page 90 IBM power cord part number Used in these countries and regions 13F9979 Afghanistan, Albania, Algeria, Andorra, Angola, Armenia, Austria, Azerbaijan, Belarus, Belgium, Benin, Bosnia and Herzegovina, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Cape Verde, Central African Republic, Chad, Comoros, Congo (Democratic Republic of), Congo (Republic of), Cote D’Ivoire...
- Page 91 IBM power cord part number Used in these countries and regions 6952300 Antigua and Barbuda, Aruba, Bahamas, Barbados, Belize, Bermuda, Bolivia, Caicos Islands, Canada, Cayman Islands, Colombia, Costa Rica, Cuba, Dominican Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Jamaica, Mexico,...
- Page 92 IntelliStation A Pro Type 6217: Installation Guide...
-
Page 93: Index
40 Serial ATA drives 29 creating an Enhanced Diagnostics CD 55 an IBM Enhanced Diagnostics an IBM Enhanced Diagnostics CD 54 creating 54 an IBM Enhanced Diagnostics diskette 54 creating an IBM Enhanced Diagnostics 55 custom configuration 50 CD-ROM drive... - Page 94 HostRAID feature for SATA an IBM Enhanced Diagnostics enabling 47 creating 54 using to configure the integrated SATA controller 47 drive, problems 63 HostRAID feature for SCSI IBM Enhanced Diagnostics 54 enabling 48 recovery repair 53 using to configure the SCSI controller 49...
- Page 95 microprocessor (continued) removable media drives, installing 22 board 15 removing installing 36 bezel 18 problems 65 cover 16 specifications 5 support bracket 17 microprocessor board 15 replacing connectors 15 bezel 39 error LEDs 69 cover 40 installing 33 retaining clips, DIMM 32 microprocessor problems 65 rope clip, installing for security 38 modes, Ethernet 51...
- Page 96 using Adaptec RAID Configuration Utility 47 Product Recovery program 70 SCSI HostRAID to configure the controller 49 ServeRAID Manager 49 the Adaptec HostRAID configuration programs 46 the SATA HostRAID feature 47 the SCSI HostRAID feature 48 the SCSISelect Utility 48 utility program Configuration/Setup 47 SCSISelect 51...
- Page 98 Part Number: 31R1983 Printed in USA (1P) P/N: 31R1983...