Table of Contents
Advertisement
DO NOT DISCARD CONTENTS
The product in this packaging was placed in the market after August 13, 2005. Its components must not be discarded with
normal municipal or household waste.
Contact your local waste disposal agency for recovery, recycling, or disposal instructions.
Assembly Instructions
Type 960 Class I & II .96 Meter Antenna System
Type 123 Class I & II 1.2 Meter LFL Antenna System
with Factory Assembled Az/El Cap Mount
One Company. A World of Solutions.
Customer Support Center
Andrew Corporation
From North America
3 Westbrook Corporate Center
Telephone: 1-800-255-1479
Suite 900
Fax: 1-800-349-5444
Westchester, Illinois 60154 USA
satcom@andrew.com
8000842-01
International
Printed in U.S.A.
Telephone: +1-708-873-2307
Fax: +1- 708-349-5444
8/06 8000842-01 Rev B
Internet: www.andrew.com
Advertisement
Table of Contents
Related Manuals for Andrew Type 960 Class I & II
Summary of Contents for Andrew Type 960 Class I & II
- Page 1 The product in this packaging was placed in the market after August 13, 2005. Its components must not be discarded with normal municipal or household waste. Customer Support Center International Printed in U.S.A. Andrew Corporation Telephone: +1-708-873-2307 From North America Contact your local waste disposal agency for recovery, recycling, or disposal instructions. 3 Westbrook Corporate Center...
- Page 2 INTERRUPTION OF BUSINESS, OR INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND. BOLT, HEX HEAD M8 x 20 In no event shall ANDREW be liable for damages in an amount greater than the purchase price of the equipment. ITEM 26 Some states do not allow limitations on how long an implied warranty lasts, or allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.
-
Page 3: Parts List
The owner and installer assumes full responsibility that the installation is structurally sound to support all loads (weight, wind & ice) and properly sealed against leaks. Andrew will not accept liability for any damage caused by a satellite system due to the many unknown variable... - Page 4 GROUND POLE INSTALLATION (96cm System) AZ-EL MOUNT WITH M8 INSERT AND SET SCREW 2.88" or 2.88" or 3.00" O.D. 3.00" O.D. IMPORTANT M8 x 20 mm Hex Head Set Screws are recommended for schedule 40 (.203 wall) mast and 1" to 2" NOT RECOMMENDED for mast with a wall thickness less than 10 ga (.134) such as 36.4"...
- Page 5 GROUND POLE INSTALLATION (1.2m System) APPENDIX B 1.2m Antenna Survival Windloads at 125 MPH Velocity 2.88" or 2.88" or 3.00" O.D. 3.00" O.D. 1" to 2" 35.8" SLOPE FOR 40.9" 1" to 2" WATER RUN OFF NOTE: SLOPE FOR 35.8" GRADE WATER RUN OFF 72"...
-
Page 6: Assembly And Installation
ASSEMBLY AND INSTALLATION INSTALLING AZ/EL CAP MOUNT ONTO POLE TOP BRACKET APPENDIX A The AZ/EL Cap is factory preassembled, therefore, no assembly is required. Before installing AZ/EL Cap onto "U" BRACKET 96cm Antenna Survival Windloads at 125 MPH Velocity ground pole, a concrete foundation should be in place and cured. - Page 7 ASSEMBLY AND INSTALLATION EARTH STATION ANTENNA AZIMUTH (IN DEGREES) FEED AND FEED LEG INSTALLATION ROUND HEAD SQUARE NECK BOLT (2 REQ) NOTE: Long formed end of Side Feed Leg attaches to MOUNT EXTENSION ASSEMBLY PLATE the Reflector rim, short formed to side of Feed Support Terminal.
-
Page 8: Elevation Chart
ELEVATION CHART ASSEMBLY AND INSTALLATION " L" IS THE DIFFERENCE BETWEEN THE EARTH STATION 1.2m System (Ref. Fig. 1.6) ANTENNA SITE LONGITUDE AND THE SATELLITE LONGITUDE Attach Side Feed Legs and Braces to left and right RD HD SQ NK BOLT TOOTH WASHER sides of Reflector using M6 x 20mm Hex Bolts, Lock FLAT WASHER... -
Page 9: Polarization Chart
POLARIZATION CHART ANTENNA ALIGNMENT PROCEDURE Alignment with the satellite is obtained by setting polariza- " L" IS THE DIFFERENCE BETWEEN THE EARTH STATION HORN SCALE tion, elevation and azimuth. Charts 1, 2 & 3 are to determine ANTENNA SITE LONGITUDE AND THE SATELLITE LONGITUDE these values for your earth station antenna site.