Kenmore 2029219 - Canister Vacuum Use And Care Manual page 20

Review this table tofind do-it-yourself solutions forminor performance problems, Any other
service needed should b eperformed byaSears o rother q ualified service agent
, WARNING
Always turn off and unplug vacuum cleaner before performing maintenance to the
vacuum cleaner. Failure to do so could result in electrical shock or personal
injury.,
Vacuum c_eaner won't s tart.
Poorjob of dirt
pick.up,
Vacuum cleaner starts but
shuts off
I Unplugged atvaBI 0ulleL
2 Tdpped d rcuilbreakort0town fuse
at household servi_ panel
3 Loose hose electficel conn._ctiens,
Full o r d_ged duelbag
2, Clogged a lHlow passages
3o Didyfiltem
4, Wrong pileheight s elting
5. Suclico controtis open
6 Hole i nhose
7 Worn Power-Mate agitalor
8 Worn orbroken bell
9 Oi_ly
agitalor or end caps.
10 Canister hcod open
I, Hose or hood electrical conneclions
2. THpped overload protector in
Power-Mate,
1 Pluginfirmly, pushONIOFF s wilchtoON
2 Resel c ircuit b reaker o r replace fuse
3. Reconnect
hose ends
t Change b ag
2 Clear a irflow passages
3 Change f iffers
4, Adjust s et_ing
5. Adjusl c oatml
6, Replace h ose
7 Change a qilat0r,
8 & goSeet_ELTCHANGING AND AGITATOR
CLEANING,
'l& Close andlalchhood
'L _ mnr_,_ns, r eo_ned I_oe e,"_
2, Remove a nyilemsthatmaybecaughl
oriammed , lhen r eset,l[vacuum cleaner s leds
andstops again, c lean agRalor endendcaps,
thenreseL
3 Tdpped t hermal protector 3..Reset l hermal p roleclor
incanister.
Power.Mate will n ot I. Power-Male connections i. Pluginfirmly
r#n whena!:lached, unplugged
2 Worn orbroken belt, 2 & 3, SeeBELT CHANGING A ND AGITATOR
3 O]dy agitator or endcaps, CLEANING
Remove a nyilems lhalmaybecaught
4 Trippedovafloadpower.Male protector in 4.,or ammed, lhenreseL gvacuum cleaner s leds
andslopsagain, c lean agitalor a ndend capE,
thenreset,
& Switch not in CARPEl" position 5.Move switch, le CARPETposilion
.... _/acuum cleaner p icks Up 1 Wrong pileheightselling I, Adjusf s etting
moveable r ugs-or- 2 _uclion toostrong 2 Opensuclion control
Power-Mate pushes toohard
Lightwon't work 1- Burned oullightbulb, 1, Change l ightbulb,
2. Tripped o verload p rotector in 2, Remove a nyilemsthatmaybecaughl
Power-Mate or ammed, thenreseLgvacuum cleaner s tarts
end s ops again, clean agi aor and end caps,
then r e.sol
Cordwon'trewind 'i Oidypower c ord t Clean thepower c ord
2 Cordiammed 2 Pull o utcard andrewind
Vacuum cleaner l eaves m arks 't Wrong vacuuming pattern 1 SeeVACUUMING TIPS,
oncarpet
2O