Adjusting Sound Setting In Manual Mode; Turning Subwoofer On/Off; Setting The Subwoofer System; Setting The Subwoofer Phase - Alpine CDA-9886R Owner’s Manual

Adjusting Sound Setting in Manual Mode

You can change these sound settings to create your own preference
when the MultEQ mode is set to MultEQ off (Manual Mode).
Use steps 1 to 4 to select one of the Sound menu
modes to modify. See the applicable section below for
details about the selected item.
1
Press IMPRINT to activate the Sound menu
selection mode.
2
Turn the Rotary encoder to select the desired item,
and then press /ENT.
Subwoofer SUBW. System
1
*
SUBW. Channel Factory's EQ
Filter Type Media Xpander
TCR Parameter Sound Field
(e.g. Select Subwoofer)
1
* These functions are inoperable when Subwoofer is set to OFF.
2
* This function can be operable only when PXA-H100 (sold
separately) is connected and 2.2ch (3WAY) mode is set. For details,
refer to the Owner's Manual of PXA-H100.
3
* This function is inoperable when Media Xpander is set to OFF.
4
* In step 2, three sound adjustment items (Parametric EQ/Graphic EQ,
T.Correction, X-Over) can be selected in Sound Field Adjustment
mode, turn the Rotary encoder to select the desired item, and then
press /ENT to continue to step 3.
3
Turn the Rotary encoder to change the setting,
and then press /ENT.
(e.g. Select Subwoofer ON or Subwoofer OFF)
4
Press and hold /ESC for at least 2 seconds to
return to normal mode.
• Media Xpander, Factory's EQ, Parametric EQ/Graphic EQ
Adjustment, EQ Mode and MX Level Adjustment are inoperable
when Defeat is set to ON.
• Pressing /ESC returns to the previous Sound menu mode.
• If no operation is performed for 60 seconds, Sound menu mode is
cancelled.

Turning Subwoofer ON/OFF

When the subwoofer is on, you can adjust the subwoofer output level
(refer to page 16).
OFF ON (Initial setting)
1 1
* SUBW. Phase *
2
*
TW Setup
3
MX Level * EQ Mode
4
* Black Out Subwoofer

Setting the Subwoofer System

When the subwoofer is on, you can select either System1 or System2
for the desired subwoofer effect.
1 (Initial setting) 2
System 1 : Subwoofer level changes according to the main
volume setting.
System 2 : Subwoofer level change is different from the main
volume setting. For example, even at low volume
settings, the subwoofer is still audible.

Setting the Subwoofer Phase

PHASE 0° (Initial setting)
The subwoofer output phase is toggled SUBWOOFER NORMAL (0°)
or SUBWOOFER REVERSE (180°). To adjust the level, turn the
Rotary encoder.
Setting the Subwoofer Channel
(SUBW. Channel)
You can set the subwoofer output to stereo or monaural. Make sure to
set the correct output for your subwoofer type.
STEREO (Initial setting)
STEREO: Subwoofer stereo (L/R) output
MONO: Subwoofer monaural output

Equalizer Presets (Factory's EQ)

10 typical equalizer settings are preset at the factory for a variety of
musical source material.
Flat Pops Rock
Electrical Dance Hip Hop&Rap
Country Classical User1
User4 User5 User6
• By selecting User's 1 to 6, you can recall the stored preset number in
"Adjusting the Graphic Equalizer Curve" (page 31) or "Adjusting
the Parametric Equalizer Curve" (page 30) .
PHASE 180°
MONO
News Jazz&Blues
Easy Listening
User2 User3
29
-EN