Page 1: Lcd Display
SyncMaster 400CXN,460CXN LCD Display User Manual...
Page 2: Safety Instructions
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.
Page 3 Safety Instructions Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. • Otherwise, this may cause fire due to overheating. Do not disconnect the power cord while using the product.
Page 4 Safety Instructions Do not install it in a badly ventilated location such as a bookcase or closet. • Otherwise, this may result in fire due to an increase in the internal temperature. When putting the product down, make sure to put it down softly. •...
Page 5 Safety Instructions Clean the product using a soft cloth with a monitor cleaner only. If you must use a cleaner other than the monitor cleaner, dilute it with water at a ratio of 1:10. When cleaning the power plug pins or dusting the power outlet, clean it with a dry cloth.
Page 6 Safety Instructions When you drop the product or the case is broken, turn the power off and disconnect the power cord. Contact a Service Center. • Otherwise, this may result in electric shock or fire. If thunder or lightening is occurring, do not touch the power cord or antenna cable.
Page 7 Safety Instructions When using headphones or earphones, do not turn the volume too high. • Having the sound too loud may damage your hearing. If you continually move closer to the product screen, your eyesight may be failing. Take a rest for at least five (5) minutes after using the monitor for one (1) hour.
Page 8 Safety Instructions Use only the specified standardized batteries, and do not use a new battery and a used battery at the same time. • Otherwise, the batteries may be damaged or cause fire, personal in- jury or damage due to a leakage of the internal liquid. The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling purposes.
Page 9: Package Contents
Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Note This stand is not for the Floor Standing Type. Unpacking LCD Display Manuals...
Page 10 Introduction Others Remote Control Batteries (AAA X 2) Cleaning Cloth (Not available in all loca- tions) HDD Cover Sold separately DVI Cable Wall Mount KIT LAN Cable Semi Stand KIT Note Cleaning Cloth is only provided for highly polished black products as a product feature. Your LCD Display Front MENU button [MENU]...
Page 11 Introduction Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Navigate buttons (Down-Up buttons) / Channel buttons Moves from one menu item to another vertically or adjusts selected menu values. / When OSD is not on the screen, push the button to adjust channel.
Page 12 Introduction POWER S/W ON [ ] / OFF [O] Switches the LCD Display On/Off. POWER IN The power cord plugs into the LCD Display and the wall plug. RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port DVI / PC / HDMI IN [DVI/PC/HDMI AUDIO IN] (PC/DVI/HDMI Audio Connection Terminal (Input)) DVI / PC / HDMI IN [HDMI]...
Page 13 Introduction AV IN [VIDEO] (VIDEO Connection Termi- nal) AV AUDIO IN [L-AUDIO-R](LCD Display Audio Connection Terminal (Input)) AUDIO OUT [L-AUDIO-R] (LCD Display Audio Connection Terminal (Output)) SERVICE This is a reserved terminal used for servicing. ANT IN Connect the CATV cable or TV antenna cable to the "ANT IN"...
Page 14: Remote Control
Introduction Kensington Lock The Kensington Lock is a device used to physi- cally fix the system when using it in a public place. The locking device has to be purchased separately. The appearance and locking method may differ from the illustration depending on the manufacturer.
Page 15 Introduction POWER Number Buttons button + VOL - MUTE TV/DTV MENU INFO COLOR BUTTONS TTX/MIX STILL AUTO S.MODE LOCK SOURCE ENTER/PRE-CH CH/P D.MENU GUIDE RETURN Up-Down Left-Right buttons EXIT MagicInfo P.MODE DUAL/MTS SWAP Turns the product On. POWER Turns the product Off. 3.
Page 16 Introduction The "-" button operates only for DTV. It is used to select MMS (multi-channel) for a DTV. 4. DEL button 5. + VOL - Adjusts the audio volume. Pauses (mutes) the audio output temporarily.This is displayed on MUTE the lower left corner of the screen.The audio resumes if MUTE or - VOL + is pressed in the Mute mode.
Page 17 Introduction 24. Up-Down Left-Right but- Moves from one menu item to another horizontally, vertically or tons adjusts selected menu values. Exits from the menu screen. EXIT SRS TS XT 27.MagicInfo MagicInfo Quick Launch Button. 28. P.MODE When you press this button, current picture mode is displayed on the lower center of the screen.
Page 18 Introduction LCD Display Head...
Page 19: Installation Vesa Bracket
Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket. • At least 2 persons are needed in order to move the LCD Display. • SAMSUNG is not responsible for any product damage or any injury caused by installation at customer's discretion.
Page 20: Wall Bracket Installation
• Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
Page 21 Introduction When done, mount the wall bracket on the wall. There are two hinges(left and right). Use the correct one. Captive Screw Wall Bracket Hinge (Left) Hinge (Right) Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct.
Page 22 Introduction To mount the product on the wall bracket The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same) Remove the 4 screws on the back of the product. Insert the screw B into the plastic hanger.
Page 23 Introduction Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket. LCD Display Wall Bracket Wall...
Page 24 Introduction Make sure to use the top center, and not the leftor the right side of the product to adjust the angle. Mechanical Layout (460CXn) Mechanical Layout LCD Display Head...
Page 25 Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket. • At least 2 persons are needed in order to move the LCD Display. • SAMSUNG is not responsible for any product damage or any injury caused by installation at customer's discretion.
Page 26: Wall Bracket Assembly
• Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
Page 27 Introduction There are two hinges(left and right). Use the correct one. Captive Screw Wall Bracket Hinge (Left) Hinge (Right) Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct. If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length.
Page 28 Introduction To mount the product on the wall bracket The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same) Remove the 4 screws on the back of the product. Insert the screw B into the plastic hanger.
Page 29 Introduction Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket. LCD Display Wall Bracket Wall...
Page 30 Introduction Make sure to use the top center, and not the leftor the right side of the product to adjust the angle.
Page 31: Connecting A Computer
Connections Connecting a Computer Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un- wiring the earth lead, make sure to disconnect the AC power in advance. Note AV input devices such as DVD players, VCR's or camcorders as well as your computer can be con- nected to the LCD Display.
Page 32: Connecting To Other Devices
Turn on both your computer and the LCD Display. • The DVI cable is optional. • Contact a local SAMSUNG Electronics Service Center to buy optional items. Connecting to Other devices Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power.
Page 33: Connecting Av Devices
Connections • When using an outdoor antenna: If you are using an outdoor antenna, use a professional for installation if possible. • To connect the RF cable to the antenna input terminal: Keep the copper wire portion of the RF cable straight. Turn on the LCD Display.
Page 34: Connecting Using A Dvi To Hdmi Cable
Connections Locate the A/V output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the AV AUDIO IN [L-AUDIO-R] on the LCD Display. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV IN [VIDEO] on the LCD Display.
Page 35: Connecting To An Audio System
Connections Connecting to an Audio System Note • Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and AUDIO OUT [L-AUDIO-R] on LCD Display. Connecting a LAN Cable Using a Power cord with Earth •...
Page 36: Connecting A Usb Device
Connections Connecting a USB device Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un- wiring the earth lead, make sure to disconnect the AC power in advance.
Page 37: Using The Software
Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ (Worldwide) Installing the Monitor Driver (Automatic) Insert CD into the CD-ROM drive. Click "Windows". Choose your monitor model in the model list, then click the "OK" button.
Page 38: Installing The Monitor Driver (manual)
Using the Software Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Installing the Monitor Driver (Manual) ® Microsoft Windows Vista™‚ Operating System Insert your Manual CD into your CD-ROM drive.
Page 39 Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. Click "Update Driver..." in the "Driver" tab. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer".
Page 40 Using the Software Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close" ! ’ "Close" ! ’ "OK" ! ’ "OK" on the following screens displayed in sequence. ®...
Page 41 Using the Software Insert CD into the CD-ROM drive. Click "Start" ! ’ "Control Panel" then click the "Appearance and Themes" icon. Click "Display" icon and choose the "Settings" tab then click "Advanced...". Click the "Properties" button on the "Monitor" tab and select "Driver" tab. Click "Update Driver..."...
Page 42 If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Click the "Close" button then click "OK" button continually.
Page 43 Using the Software 10. Monitor driver installation is completed. ® ® Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. Choose "OK" button on the "Insert disk" window. Click the "Browse" button on the "File Needed" window. Choose A:(D:\Driver) then click the "Open"...
Page 44 Using the Software Select the "Monitor" tab. Click the "Change" button in the "Monitor Type" area. Choose "Specify the location of the driver". Choose "Display a list of all the driver in a specific location..." then click "Next" button. Click the "Have Disk" button. Specify A:\(D:\driver) then click "OK"...
Page 45 Using the Software Installation MagicInfo Pro Installation Insert CD into the CD-ROM drive. Click the MagicInfo Pro installation file. When the Install Shield Wizard window appears, click "Next." Select "I agree to the terms of the license agreement" to accept the terms of use. You are required to log in to the MagicInfo Pro Server program.
Page 46 Using the Software Choose a folder to install the MagicInfo Pro program. Click "Install."...
Page 47 Using the Software The "Setup Status" window appears. It is recommended restarting the system for the normal operation of the MagicInfo Pro Server program. Click "Finish."...
Page 48: System Requirements
Using the Software 10. When the installation is complete, the MagicInfo Pro executable icon appears on your desktop. 11. Double-click the icon to start the program. System Requirements Ethernet Application Minimum P1.8 256M 100M/1G Windows XP WMP 9 or Windows later Recommen- P3.0Ghz...
Page 49: Main Screen
Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a display. Main Screen Click Start > Program > Samsung > MDC System to start the program. Select a set to see the volume of the selected set within the slider.
Page 50: Port Selection
Main Icons Select Button Remocon Info Grid Safety Lock Display Selection Port Selection Control Tools 1. Use the main icons to switch into each screen. 2. Allows you to enable or disable the remote control signal receiving function of the display unit. 3.
Page 51: Power Control
1. The Multiple Display Control is originally set to COM1. 2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu. 3. If the exact port name that is connected to the LCD Display using a serial cable is not selected, communication will be unavailable.
Page 52 Info Grid shows some basic information necessary to Power Control. (Power Status) 2) Input 3) Image Size 4) On Timer 5) Off Timer 2. Use the Select All button or Check Box to choose a display to control. Power Control allows controlling some of the functions of the selected display. 1) Power On/Off...
Page 53: Input Source
- Turns the power of the selected display On/Off. 2) Volume - Controls the volume level of the selected display. It receives the volume value of the selected display from the sets and displays it in the slider. (When you cancel the selection or choose Select All, the value returns to the default value 10) (Mute On/Off) - Turns on/off the Mute function of the selected display.
Page 54: Image Size
Info Grid shows some basic information necessary to Input Source Control. - Changes the Input Source of the selected display to PC. - Changes the Input Source of the selected display to BNC. - Changes the Input Source of the selected display to DVI. - Changes the Input Source of the selected display to TV.
Page 55 Info Grid shows some basic information necessary to Image Size Control. ( Power Status) - Shows the power status of the current display. 2) Image Size - Shows the current Image Size of the display in use. 3) Input - Shows the current Input Source of the display in use. 4) Info Grid displays only the displays whose Input Source is PC, BNC, DVI.
Page 56 Info Grid shows some basic information necessary to Image Size Control. 1) Click the Video Source tab to adjust Image Size for TV, AV, S-Video, Component, DVI(HDCP), HDMI, DTV. Click Select All or use Check Box to select a display to control. 2) Info Grid displays only the display having TV, AV, S-Video, Component or DVI(HDCP) as input source.
Page 57: Pip Size
Info Grid shows some basic information necessary to Time Control. 1) Current Time - Set the current time for the selected display (PC Time). - To change the current time, first change the PC Time. 2) On Time Setup - Set the Hour, Minute, AM/PM of On Time Setup, Status, Source, Volume of the selected display. 3) Off Time Setup - Set the Hour, Minute, and AM/PM, Status for Off Time Setup of the selected display.
Page 58: Pip Source
Info Grid shows some basic information necessary to PIP Size Control. 1) PIP Size - Shows the current PIP Size of the display in use. 2) OFF - Turns off the PIP of the selected display. 3) Large - Turns on the PIP of the selected display and changes the size to Large. 4) Small - Turns on the PIP of the selected display and changes the size to Small.
Page 59 Info Grid shows some basic information necessary to PIP Source Control. 1) PIP Source - PIP Source can be controlled with turning on the LCD Display power. 2) PC - Changes the source of the PIP of the selected display to PC. 3) BNC - Changes the source of the PIP of the selected display to BNC.
Page 60: Picture Pc
Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide.When selected, each function fetches the value for the set and displays it on the slide bar. When "Select All" is chosen, the default value is displayed.
Page 61 1. Click Settings of the main icons and the Settings Control screen appears. Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide. When selected, each function fetches the value for the set and displays it on the slide bar.
Page 62: Image Lock
Audio 1. Click Settings of the main icons and the Settings Control screen appears. Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide. When selected, each function fetches the value for the set and displays it on the slide bar.
Page 63: Lamp Control
Info Grid shows some basic information necessary to Settings Control. 1) Image Lock - Available only for PC, BNC. 2) Coarse - Adjusts Coarse of the selected display. 3) Fine - Adjusts Fine of the selected display. 4) Position - Adjusts Position of the selected display. 5) Auto Adjustment - Self-Adjust to the incoming PC signal.
Page 64 An "Info Grid" showing several basic data items appears. 1) Maintenance - Allows the Maintenance Control function for all input sources. 2) Auto Lamp Control - Automatically adjusts the backlight of the selected display at a specified time. The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control. 3) Manual Lamp Control - Allows you to adjust the backlight of the selected display regardless of the time.
Page 65: Video Wall
1) Safety Screen - Eliminates the afterimages that can result when the selected display stays in Pause mode for an extended period of time. You can set the repeat cycle timer by selecting the "Interval" by hour and "Second" by second. It can be set to Scroll, Pixel, Bar and Eraser by Screen Type.
Page 66: Troubleshooting
Select a display from Display Selection. The place will be set up by pressing a number in the selected mode. The MDC program supplied by Samsung supports up to 5x5 LCD Displayes. 3) On / Off - Turns on/off the Video Wall function of the selected display.
Page 67: Settings Value Display In Multiple Display Mode
- Check the displays to see if any of the other displays connected have the same ID. If more than one displays have the same ID, those displays are not properly detected by the program due to data conflict. - Check if the Display Set ID is a number between 0 and 25. (Adjust using the Display menu) Note : A Display Set ID must be a value between 0 and 25 .
Page 68 What is MagicInfo Pro? Using MagicInfo Pro Library Screen Schedule Client / Contents Remote Management Message Option Troubleshooting Server What is MagicInfo Pro? MagicInfo Pro uses an Ethernet network for servers and monitors, and transfers media files (image files, music files, and movies) and office files (HTML, PDF) from the server to the monitors over the network.
Page 69 schedules. 5. Instants message → You can display a message on selected monitors regardless of schedules. 6. MDC and System → The MDC and System functions allow you to control, view the status of, and diagnose monitors. 7. VNC → The VNC function allows you to connect to a monitor remotely and view the status of and control and diagnose it.
Page 70 What is MagicInfo Pro? Using MagicInfo Pro Library Screen Schedule Client / Contents Remote Management Message Option Troubleshooting Server Using MagicInfo Pro Running MagicInfo Pro 1. Click Programs -> MagicInfo Pro -> MagicInfo Pro. 2. When MagicInfo Pro runs, select Log In from the File menu. 3.
Page 71 2. Configure the Network Connection settings In the General tab. Enter the server name on the monitor identical to the name of the server. To change the server name, double-click the Value field of the Server Name item. 3. If there is more than one network card in the server, select a network card in the Network Device item.
Page 72 MagicInfo in the OSD pages.) 2. A message is displayed to notify that the monitor is successfully connected to the server. File Sub-Menus Registering a Library 1. Select Library from the File menu to open the Library View. 2. Select a photo file, music file, movie file, document, or Flash file etc. on the server. 3.
Page 73 4. The registered library files are used by the monitor when the Operating Mode of the monitor is set to Player or is used when registering a screen. Registering a Screen 1. Select Screen from the File menu to open a Screen View. 2.
Page 74 5. Repeat steps 2 to 4 to register other areas on a screen. 6. After finishing registering areas, select Save from the File menu to save the screen. 7. Register a schedule to display the saved screen on a monitor(s). Registering a Schedule 1.
Page 75 4. If you want to change the date or time of the schedule, drag it to a different date or time. 5. Select Publish from the Tools menu. Select the checkbox next to the monitors for which you want to register the selected schedule.
Page 77 What is MagicInfo Pro? Using MagicInfo Pro Library Screen Schedule Client / Contents Remote Management Message Option Troubleshooting Server Library File Menu Library / Screen / Schedule / Remote Management / Message Creates a view or selects a created view for each menu item so that you can perform a screen schedule and have basic control over the monitors from the server.
Page 78 Tools Menu Synchronize Synchronizes the library files of the main server with the files of the content server. Option Changes the server settings. For more information, refer to the Options section. Library...
Page 79 Tree View List View Output View Tree View All the folders under My Computer on the Windows Desktop, library, screen, and content server are displayed in a tree view. If you select a folder, its subfolders and a list of files in it are displayed in the list view in the right pane. Exploring Normal Files Exploring Libraries Exploring Screen Files...
Page 80 Displays the screen management folders created with the Screen menu in a tree view. Function: Displays the subfolders and screen files below the selected folder in the list window on the right by selecting a folder. Hot Key F2 key: Renames the selected folder. Delete key: Deletes the selected folder, its sub folder(s) and all the files in the selected folder and subfolders.
Page 81 Double-click to move to the upper folder. Double-click to move to the lower folder. Double-click a file to run the file. Drag & Drop If you drag and drop a file from the list view into a library, it is registered to that library. However, the drag &...
Page 82 If you drag and drop library files into a library folder in the tree view or list view, they are moved to that folder if the content types of both the library files and the library folder are the same. However, the drag &...
Page 83 - Comments : Comments entered by the user for the selected library file. You can edit them. New Folder: This menu item is only activated when neither a folder nor a file is selected. If you select this menu item, a new folder is created. However, it is deactivated when a library or office folder is selected in the tree view.
Page 84 If you drag and drop screen files to a screen folder in the tree view or the list view, they are moved to that folder. However, the drag & drop function is not supported for folders. Context Menu Open: If you click Open for a folder, you are moved to that folder. However, this menu item is deactivated when a screen file is selected.
Page 85 - Name: The name of the selected screen - Location : The location where the selected screen is registered - Size : The size of the selected screen - Resolution : The resolution of the selected screen - Duration : The playing time of the selected screen - Date Modified : The date when the selected screen was last modified - Target : The real location of the selected screen.
Page 86 Displays the subfolders and content servers below the selected folder. Function: Double-Click Double-click to move to the upper folder. Double-click to move to the lower folder. Drag & Drop If you drag and drop content servers to a content server folder in the tree view or the list view, they are moved to that folder.
Page 87 1) Mac Address: The MAC address of the selected content server. You can edit this. 2) Server Name: The server name of the selected content server. You can edit this. 3) IP Address: The IP address of the selected content server. You cannot edit this. * The IP address is displayed if the content server is connected at least once.
Page 88 Hot Key Ctrl + C: Copies the selected message to the clipboard so that you can paste it to another location.
Page 89 What is MagicInfo Pro? Using MagicInfo Pro Library Screen Schedule Client / Contents Remote Management Message Option Troubleshooting Server Screen File Menu Library / Screen / Schedule / Remote Management / Message Creates a view or selects a created view for each menu item so that you can perform a screen schedule and performs basic control for the monitors from the server.
Page 90 accounts that can be created: Administrator and User Accounts Administrator: Has privileges for all server functions. User: Has privileges for all server functions except for changing server options and user account features. Exit Exits the program. If there are any unsaved changes, a new window is displayed so that you can save them.
Page 91 Screen Tree View Edit View List View Tree View A tree is created in accordance with the order of the areas created in the Edit View. You can check the area currently selected in the Edit View using the Tree View. If you select a property of an area, the detailed property information is displayed in the List View.
Page 92 New: Initializes the screen view you are currently working with. If there are any unsaved changes, a new window is displayed so that you can save them. Open: Opens a screen file. If there are any unsaved changes, a new window is displayed so that you can save them.
Page 93 Name: Changes the background name. You cannot use a name already used for another area name. Resolution: Changes the resolution for the background. You can add a new resolution and set the default resolution using the Options menu. Start Time, Stop Time, Duration: Sets the playing time of the background in minutes. The playing time of the background changes to that of the screen.
Page 94 Tile: The photo file is tiled continuously across the entire background. Time Interval: Sets the slide show time between photo files when the background type is set to Photo File. Office File: Selects the office files when the background type is set to Office File. You can create the background using a Power Point, Excel, Word, or PDF file.
Page 95 Sound: Turns the background sound on or off. Music File: Selects a music file for the background. Volume: Controls the volume of the background music. Repeat: A music file can be played repeatedly. When set to Repeat, the music file is played repeatedly while the background is created.
Page 96 Photo This function is for configuring screens using photo files and consists of the Area, Screen, Background, Effect functions. The Area function allows you to set the position where the photo is displayed and when and for how long it is displayed. The Screen function allows you to select photo files and how to display them.
Page 97 Screen Photo File: Selects a photo file to play in the Photo area. Aspect Ratio: Selects the aspect ratio for the photo files to be played in the Photo area. Full: The photo file is enlarged or reduced to fit the entire background. Original: The photo file is displayed at the original size.
Page 98 Picture File: Selects the photo file when the background type for the Photo area is set to Picture File. Picture Aspect Ratio: Selects the aspect ratio for the photo file when the background type of the Photo area is set to Picture File. Full: The photo file is enlarged or reduced to fit the entire background.
Page 99 Effect: Selects the type of effect to be applied when the Photo area is created. None: No effect is used. Slide: The Photo area is created while it is moving. Block: The Photo area is created with blocks. Fade In: The Photo Area fades in when it is created. Effect Speed: Adjusts the speed of an effect being created.
Page 100 Name: Changes the area name. You cannot use a name already used for another area name. Lock Position: Locks the position of the area. Left, Top, Width, Height: Changes the position and size of the area. The area positions must be within the background and the area size cannot be larger than the background size.
Page 101 Movie Repeat: A movie file can be played repeatedly. When set to Repeat, the movie file is played repeatedly while the background is created. Background Type: Sets the background type (Color, Picture File) for the Movie area. Color: Selects the color when the background type for the Movie area is set to Color. Transparency: Selects the degree of transparency when the background type for the Movie area is set to Color.
Page 102 Changes the detailed properties and the transfer mode for the selected file of each type. Transfer Mode: Changes the mode in which the selected file is transferred to the monitor. Download: Downloads the file to the monitor and plays it. Stream: Streams the file to the monitor.
Page 103 This function is for configuring screens using Macromedia flash files and consists of Area, Screen, Background, Effect functions. The Area function allows you to set the position where the movie is played and when and for how long it is played. The Screen function allows you to set the flash file and how to play it.
Page 104 Screen Flash File: Selects the flash file to be played in the Flash area. Aspect Ratio: Selects the aspect ratio for the flash file to be played in the Flash area. Full: The flash file is enlarged or reduced to fit the entire background. Original: The flash file is displayed at the original size.
Page 105 Picture Aspect Ratio: Selects the aspect ratio for the photo file to be played in the Flash area when the background type of the Flash area is set to Picture File. Full: The photo file is enlarged or reduced to fit the entire background. Original: The photo file is displayed at the original size.
Page 106 Effect: Selects the type of effect to be applied when the Flash area is created. None: No effect is used. Slide: The Flash area is created while it is moving. Block: The Flash area is created with blocks. Fade In: The Flash area fades in when it is created. Effect Speed: Adjusts the speed of an effect being created.
Page 107 Name: Changes the area name. You cannot use a name already used for another area name. Lock Position: Locks the position of the area. Left, Top, Width, Height: Changes the position and size of the area. The area positions must be within the background and the area size cannot be larger than the background size.
Page 108 Background Type: Sets the background type (Color, Picture File) for the Web area. Color: Selects the color when the background type for the Web area is set to Color. Transparency: Selects the degree of transparency when the background type for the Web area is set to Color.
Page 109 Changes the detailed properties and the transfer mode for the selected file of each type. Transfer Mode: Changes the mode in which the selected file is transferred to the monitor. Download: Downloads the file to the monitor and plays it. Stream: Streams the file to the monitor.
Page 110 This function is for configuring screens by connecting text and consists of the Area, Screen, Background, Effect functions. The Area function allows you to set the position of the text and when and for how long it is displayed. The Screen function allows you to select the text and how to display it. The Background function allows you to set the background image and music when the text is displayed.
Page 111 Text: Sets the text to be displayed in the Text area. Direction: Sets the direction of the text flow in the Text area. None Right to Left Left to Right Top to Bottom Bottom to Top Text Speed: Sets the speed of the text flow in the Text area. Step: Sets the interval of the text flow in the Text area.
Page 112 Color: Selects the color to use when the background type for the Text area is set to Color. Transparency: Selects the degree of transparency to be used when the background type for the text area is set to Color. If the Transparency is set to a value under 100, the area which is placed beneath the present area is shown transparently.
Page 113 Effect: Selects the type of effect to be applied when the Text area is created. None: No effect is used. Slide: The Text area is created while it is moving. Block: The Text area is created with blocks. Fade In: The Text area fades in when it is created. Effect Speed: Adjusts the speed of an effect being created.
Page 114 Name: Changes the area name. You cannot use a name already used for another area name. Lock Position: Locks the position of the area. Left, Top, Width, Height: Changes the position and size of the area. The area positions must be within the background and the area size cannot be larger than the background size.
Page 115 Edit View This view is used for screen design and allows you to create, move and change the size of an area using your mouse. You can preview the current state by selecting Preview Area from the context menu or double-clicking on an area. Context Menu Area: Selects the type of area you wish to create.
Page 116 What is MagicInfo Pro? Using MagicInfo Pro Library Screen Schedule Client / Contents Remote Management Message Option Troubleshooting Server Schedule File Menu Library / Screen / Schedule / Remote Management / Message Creates a view or selects a created view for each menu item so that you can perform a screen schedule and performs basic control for the monitors from the server.
Page 117 Tool Menu Undo / Redo Cancels the previously performed command or performs the canceled command again. You can change the maximum number of commands that you can undo using the Option menu. Adds the screen you wish to schedule after selecting a monitor and time by clicking in the EPG window.
Page 118 Schedule Tree View EPG View List View Publish View Tree View Displays the connection state of the monitors currently connected to the server depending on the monitor icon. You can also efficiently manage the monitors by creating network groups. You can move a networked monitor by dragging and dropping it into a group.
Page 119 Network: A monitor which is connected to the server over a network. New Group: Creates a new group that can include some networked monitors. You can drag and drop a networked monitor to a group. Copy/Paste: Copies all the schedules configured on the selected monitor to the clipboard and pastes them to another monitor.
Page 120 This is a virtual monitor used to create schedules for a monitor used without being connected to the network. Local publishing can be performed for a local monitor to create schedules for it. New Monitor: Creates a new virtual local monitor. Copy / Paste: Copies the schedules set on the selected monitor and pastes them to another monitor.
Page 121 Add: Adds the screen you wish to schedule after selecting a monitor and time by clicking in the EPG window. Delete: Deletes the screen currently selected in the EPG window. Copy / Paste: Copies the currently selected screen and pastes it after selecting a monitor and time by clicking in the EPG window.
Page 122 Name: Changes the name of the selected screen. Only the screen name changes and the time information is retained. Start Time / Stop Time / Duration: Sets the time information for the selected screen in minutes. Periodic: Sets how frequently the selected screen recurs. (None / Daily / Weekly / Monthly) End on: Sets an end date for the selected schedule to recur.
Page 123 What is MagicInfo Pro? Using MagicInfo Pro Library Screen Schedule Client / Contents Message Option Troubleshooting Remote Management Server Remote Management File Menu Library / Screen / Schedule / Remote Management / Message Creates a view or selects a created view for each menu item so that you can perform a screen schedule and have basic control over the monitors from the server.
Page 124 Tools Menu Refresh Refreshes the value of each client for the currently selected remote control item. Option Changes the server settings. For more information, refer to the Options section. Remote Management Tree View List View Combo View...
Page 125 Tree View Displays various control items for the client in a tree view. If you select an item, the current state of the selected item is displayed and you can control it in the list view. Displays the items for which remote management is required from among the OSD menus of each client monitor in a tree view.
Page 126 1) Hour: Enter the hour. 2) Minute: Enter the minutes. 3) AM/PM: Enter AM or PM. -On Timer 1) Hour: Enter the hour. 2) Minute: Enter the minutes. 3) AM/PM: Enter AM or PM. 4) Status: Select whether to use the turn-on time. 5) Source: Select the external input 6) Volume: Select the volume -Off Timer...
Page 127 System Displays the items required to manage the client in the tree view separately from MDC. If you select an item, the current state of the selected item is displayed and you can control it in the list view. Detailed Items System: Displays the product information for the client in a list view.
Page 128 mode. The Color Temperature item is only applicable if the Color Tone item is turned off. The Auto Wide option for the Size item is only available in TV mode. (Only applicable for monitors that support TV.) Picture PC: Displays the current state of MagicBright, contrast, brightness, color tone, red, green, blue, color temp, and size.
Page 129 3) Type: Enter the type of screensaver. Video Wall 1) Video Wall: Select whether to activate the video wall. 2) Horizontal: Set how many parts the screen is divided into horizontally. 3) Vertical: Set how many parts the screen is divided into vertically. : Select the area that the monitor will display.
Page 130 System Displays the items required to manage the system properties of the client in a tree view. You have to set the settings for each item by double-clicking the client or using the Edit item from the context menu, instead of selecting each item and setting a value as in MDC. Detailed Items System: Displays the information for the model name, serial number, screen size, firmware version, MagicInfo Pro version, and OS image version.
Page 131 1) Current Status: Displays the current EWF status of the selected client. 2) EWF command: Changes the EWF status of the selected client. 3) Screen Rotation: Selects the screen direction of the selected client. 4) Screen Resolution: Displays the resolution of the selected client. 5) System message: Selects whether to display a system message for the selected client.
Page 132 Context Menu Update: This item is only enabled if a monitor name is selected. This item compares the client version to the update version on the server and updates the client if required. Edit: Displays a window so that you can change the monitor settings. For the System, General, and Performance items, the settings are read-only so they are disabled.
Page 133 What is MagicInfo Pro? Using MagicInfo Pro Library Screen Schedule Client / Contents Remote Management Option Troubleshooting Message Server Message File Menu Library / Screen / Schedule / Remote Management / Message Creates a view or selects a created view for each menu item so that you can run a screen schedule and perform basic control for the monitors from the server.
Page 134 user account features. Exit Exits the program. If there are any unsaved changes, a new window is displayed so that you can save them. Tool Menu Undo / Redo Cancels the previously performed command or performs the canceled command again. You can change the maximum number of commands that you can undo using the Option menu.
Page 135 Tree View List View Tree View You can select the monitors to which the message is sent by checking the checkbox next to each monitor and group. List View Changes the detailed functions for the message to be sent to the monitors by double-clicking it or by clicking the created button.
Page 136 What is MagicInfo Pro? Using MagicInfo Pro Library Screen Schedule Client / Contents Remote Management Message Troubleshooting Option Server Option Option General Network Connection: Selects the connection method between the server and the monitor. The server and monitor can be connected to each other only if the same connection method is used. Automatic connection: The monitor automatically connects a server on the same network.
Page 137 Direct connection: The monitor directly connects to the server with the specified IP address. If the server and monitor are on a different private network, they cannot connect to each other. However, if the server has a public IP address, a monitor with a private IP address can be connected to it using the direct connection method.
Page 138 Use the available disk space of each monitor: Sets the size to the maximum free disk space of the monitor. Use the equal disk space of each monitor: Sets the size to the value entered in the edit box. Do not check disk space when schedule is published: Publishing continues even though the total size of the schedules to be published is larger than that of the free disk space of the monitor.
Page 139 What is MagicInfo Pro? Using MagicInfo Pro Library Screen Schedule Remote Management Message Option Troubleshooting Client / Contents Server Contents Server A program run on the additional PC where the content server is operating. Version: The version of the content Server. MAC ID: The MAC address of the network device on the PC where the content server is installed.
Page 140 Displays or changes the drive settings. Password Manages the password. Setup Rotation Rotates the screen with the selected option. Program Runs or exits the program. Exit Exits mnMain. If you exit mnMain, MagicInfo Pro and the Schedule program are also exited together.
Page 141 Old password Enter the existing password. New password Enter the new password. Change Change the password. Use password lock Verifies your password before you enter the Setup screen. Setup Connection Tab Schedule server Server Connection Settings The client automatically connects to the server. When a connection is disconnected, the client connects to another server automatically.
Page 142 The ID of the server to connect to Client ID 1 Schedule server Automatic connection using server name : If the schedule server and client are on the same sub network, the client connects to the servers using their name. Reconnecting another server when disconnected : If a connection is disconnected, the client connects to another server on the same sub network automatically.
Page 143 Select the program performed when the client starts. Automatic updates Select how to perform automatic updates. 1 Startup Sets the program to be performed when the client starts. You can select one of two programs, or select neither of them. Player: Runs a media player program that can be run using the remote control and can receive and play the content that exists on the server.
Page 144 Background: Sets the background for the entire screen. File: Sets the logo screen to be displayed on the background. (A flash, photo, or movie file can be set.) 2 Schedule folder Sets the directory which the content to be scheduled is downloaded to and managed in and manages the size of the disk.
Page 145 What is MagicInfo Pro? Using MagicInfo Pro Library Screen Schedule Client / Contents Remote Management Message Option Troubleshooting Server Troubleshooting When a monitor is not connected to the server Check whether the network environment for the server and monitor is normal.. (Check the network cable connections and IP address settings, etc) Check whether a correct network card has been selected when there is more than one network card in the PC where the server is operating.
Page 146 When the monitor update function does not work Check the monitor version. If it is the latest version, no updating is performed. When a movie file is not registered to the library Check whether the proper codec is installed for the movie file the server wants to register to the monitor.
Page 147 MagicInfo Pro 소개 Screen Design Message Schedule Library Remote Management Option 문제해결 일반사양 프로그램 제거 프로그램 제거 MagicInfo Pro는 Windows 프로그램 추가/제거 옵션을 사용하거나 프로그램 설치시 추가되는 메뉴를 통해 제거할 수 있습니다. MagicInfo Pro를 제거하려면 다음 단계를 수행하십시오. 시스템 트레이에서 [시작] 메뉴로 이동하고 [설정]을 선택한 다음 메뉴에서 [제어판]을 선택합니다. 2.
Page 148: Source List
Adjusting the LCD Display Input Available Modes • PC / DVI • • HDMI • MagicInfo • Source List MENU ! ’ ENTER ! ’ [Input] ! ’ ENTER ! ’ [Source List] ! ’ , ! ’ ENTER Use to select PC, DVI or other external input sources connected to the LCD Display. Use to select the screen of your choice.
Page 149 Adjusting the LCD Display , ! ’ ENTER Name the input device connected to the input jacks to make your input source selection easier. HDMI Picture [PC / DVI / MagicInfo Mode] Available Modes • PC / DVI • • HDMI •...
Page 150 Adjusting the LCD Display Entertain High brightness For watching motion pictures such as a DVD or VCD. Internet Medium brightness For working with a mixture of images such as texts and graphics. Text Normal brightness For documents or works involving heavy text. Custom Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste.
Page 151: Color Tone
Adjusting the LCD Display , ! ’ ENTER Adjusts the Sharpness. Color Tone MENU ! ’ ! ’ ENTER ! ’ [Picture] ! ’ ! ’ ! ’ ENTER ! ’ [Color Tone] ! ’ , ! ’ ENTER The color tones can be changed. (Not available in Dynamic Contrast mode of On.) Cool Normal...
Page 152: Color Temp
Adjusting the LCD Display , ! ’ ENTER Green MENU ! ’ ! ’ ENTER ! ’ [Picture] ! ’ ! ’ ! ’ ! ’ ENTER ! ’ [Color Control] ! ’ ! ’ ENTER ! ’ [Green] ! ’ , ! ’...
Page 153: Auto Adjustment
Adjusting the LCD Display Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. Fine MENU ! ’ ! ’ ENTER ! ’ [Picture] ! ’ ! ’...
Page 154: Signal Control
Adjusting the LCD Display (Available in PC mode only) Signal Balance MENU ! ’ ! ’ ENTER ! ’ [Picture] ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ ENTER ! ’ [Signal Balance] ! ’ ENTER ! ’...
Page 155: Dynamic Contrast
Adjusting the LCD Display , ! ’ ENTER G-Offset MENU ! ’ ! ’ ENTER ! ’ [Picture] ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ ENTER ! ’ [Signal Bal- ance] ! ’ ! ’...
Page 156 Adjusting the LCD Display Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. Picture [ AV / HDMI / TV Mode] Available Modes • PC / DVI • • HDMI • MagicInfo •...
Page 157 Adjusting the LCD Display (Not available in Dynamic Contrast mode of On.) Contrast MENU ! ’ ! ’ ENTER ! ’ [Picture] ! ’ ! ’ ENTER ! ’ [Custom] ! ’ ENTER! ’ [Contrast] ! ’ , ! ’ ENTER Adjusts the Contrast.
Page 158 Adjusting the LCD Display Color Tone MENU ! ’ ! ’ ENTER ! ’ [Picture] ! ’ ! ’ ! ’ ENTER ! ’ [Color Tone] ! ’ , ! ’ ENTER The color tones can be changed. The individual Color components are also user adjustable. (Not available in Dynamic Contrast mode of On.) Cool2 Cool1...
Page 159: Film Mode
Adjusting the LCD Display , ! ’ ENTER The Size can be switched. 16:9 Zoom 1 Zoom 2 Just Scan (Not available in Dynamic Contrast mode of On.) Note The Zoom1, Zoom2 are not available HDMI. The Just Scan are available in HDMI. Digital NR (Digital Noise Reduction) MENU ! ’...
Page 160: Brightness Sensor
Adjusting the LCD Display , ! ’ ENTER Turns Film Mode Off/On. The Film Mode feature offers you a theater-quality viewing experience. (Not available in HDMI Mode) Dynamic Contrast MENU ! ’ ! ’ ENTER ! ’ [Picture] ! ’ ! ’...
Page 161 Adjusting the LCD Display Sound Available Modes • PC / DVI • • HDMI • MagicInfo • Mode MENU ! ’ ! ’ ! ’ ENTER ! ’ [Sound] ! ’ ENTER ! ’ [Mode] ! ’ , ! ’ ENTER The LCD Display has a built-in high fidelity stereo amplifier.
Page 162: Auto Volume
Adjusting the LCD Display Note • You can hear the sound even when sound value is set to 0. • If you adjust sound using Custom function, Mode will turn to Custom mode. Bass MENU ! ’ ! ’ ! ’ ENTER ! ’...
Page 163 Adjusting the LCD Display SRS TS XT MENU ! ’ ! ’ ! ’ ENTER ! ’ [Sound] ! ’ ! ’ ! ’ ! ’ ENTER ! ’ [SRS TS XT] ! ’ , ! ’ ENTER SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers.
Page 164: Clock Set
Adjusting the LCD Display Note The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. Time Selects from one of 4 time settings, Clock Set, Sleep Timer, On Timer, and Off Timer. MENU ! ’...
Page 165: Off Timer
Adjusting the LCD Display On Timer MENU ! ’ ! ’ ! ’ ! ’ ENTER ! ’ [Setup] ! ’ ! ’ ENTER ! ’ [Time ] ! ’ ! ’ ! ’ ENTER! ’ Timer] ! ’ , / , ! ’ ENTER Turns the LCD Display on automatically at a preset time.
Page 166: Energy Saving
Adjusting the LCD Display High Medium Opaque Safety Lock PIN MENU ! ’ ! ’ ! ’ ! ’ ENTER ! ’ [Setup] ! ’ ! ’ ! ’ ! ’ ENTER ! ’ [Safety Lock PIN ] ! ’ [0 9] ! ’...
Page 167 Adjusting the LCD Display , ! ’ ENTER When a DVD or set-top box is connected to your TV via HDMI, it may cause a degradation in the screen quality, such as an increase in the black level, a low contrast, or discoloration, etc., depending on the external device connected.
Page 168 Adjusting the LCD Display Format MENU ! ’ ! ’ ! ’ ! ’ ENTER ! ’ [Setup] ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ ENTER ! ’ [Video Wall ]! ’ ! ’ ENTER ! ’...
Page 169: Safety Screen
Adjusting the LCD Display , ! ’ ENTER Sets how many parts the screen should be divided vertically. Five adjustment levels: 1, 2, 3, 4, and 5. Screen Divider MENU ! ’ ! ’ ! ’ ! ’ ENTER ! ’ [Setup] ! ’...
Page 170 Adjusting the LCD Display Horizontal Dot MENU ! ’ ! ’ ! ’ ! ’ ENTER ! ’ [Setup] ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ ENTER ! ’ [Safety Screen] ! ’ ENTER ! ’...
Page 171 Adjusting the LCD Display Timer Timer MENU ! ’ ! ’ ! ’ ! ’ ENTER ! ’ [Setup] ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ ENTER ! ’ [Safety Screen] ! ’ ! ’...
Page 172 Adjusting the LCD Display Use this function to set the execution period for each mode set in the timer. Time MENU ! ’ ! ’ ! ’ ! ’ ENTER ! ’ [Setup] ! ’ ! ’ ! ’ ! ’ ! ’...
Page 173: Resolution Select
Adjusting the LCD Display Eraser MENU ! ’ ! ’ ! ’ ! ’ ENTER ! ’ [Setup] ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ ! ’ ENTER ! ’ [Safety Screen] ! ’ ! ’...
Page 174: Side Gray
Adjusting the LCD Display , ! ’ ENTER Adjusts the Power On time for the screen. Caution: Set the Power On time to be loger to avoid overvoltage. Side Gray MENU ! ’ ! ’ ! ’ ! ’ ENTER ! ’ [Setup] ! ’...
Page 175: Color Reset
Adjusting the LCD Display Note Available in PC mode only Note The Reset function is not available when Video Wall is On. Color Reset MENU ! ’ ! ’ ! ’ ! ’ ENTER ! ’ [Setup] ! ’ ! ’ ! ’...
Page 176 Adjusting the LCD Display , ! ’ [0~9] • ID Setup Assigns distinctive IDs to the SET. • ID Input Use to select the transmitter functions of the individual SET. Only a SET where the ID corresponds to the transmitter setting becomes activated. MagicInfo Available Modes •...
Page 177 Adjusting the LCD Display • To setup MagicInfo on a Windows screen, a keyboard and mouse are required. • To setup MagicInfo on a Windows screen, refer to the MagicInfo Server Help. It is highly recommended not to turn off the AC power during an operation. •...
Page 178: Slide Show
Adjusting the LCD Display Slide Show Displays the properties of the original file as they are. Interval Controls the time intervals between image files for a slide show. (5 Sec, 10 Sec, 20 Sec, 30 Sec, 60 Sec)
Page 179 Adjusting the LCD Display Rotation Displays an image file by turning it clockwise by 90 degrees. Zoom Displays a reduced picture.
Page 180 Adjusting the LCD Display Close Closes the image control Menu. Music The MP3 file format is supported. Movie The MPEG1, WMV file format are supported.
Page 181 Adjusting the LCD Display Play Plays a movie file. Full Size Plays a movie file in full screen.
Page 182 Adjusting the LCD Display OFFICE / HTML PPT(Power Point), DOC(MS Word), XLS(MS Excel), PDF, HTML, HTM files are displayed. Note • Install the proper viewer(freeware) program to see the MS Office(Word, Excel, Power Point) or PDF doucuments. Internet Connects to the Internet Setup Sets various functions in MagicInfo mode.
Page 183: Schedule View
Adjusting the LCD Display Schedule View Displays a schedule. TCP/IP Changes the TCP/IP settings.
Page 184 Adjusting the LCD Display Connection Modifies the network settings. Password The password can be changed. • The password should be between 6 and 12 characters in numeric format. (You should enter a password between 6 and 12 characters in numeric format) •...
Page 185: Play Option
Adjusting the LCD Display • If you forget the password, enter Info, 8, 2 and 4 on the remote control to initialize the password. This will reset the previous settings of Setup mode. File Local : You can delete or copy files on both local and removable disks. Play Option You can set the repeat play and screen settings.
Page 186 Adjusting the LCD Display • File Repeat - Select Repeat File to play a movie or tune in the list repeatedly. • List Repeat - Select Repeat List to play movies or tunes in the list in sequence repeatedly. Rotation - Sets the picture orientation. •...
Page 187 Adjusting the LCD Display Magnifies the size of the picture on the screen. Zoom2 Magnifies the size of the picture more than Zoom1. Wide Fit Enlarges the aspect ratio of the picture to fit the entire screen. Sets the picture to 4:3 normal mode. Just Scan Use the function to see the full image without any cutoff when HDMI (720p/1080i/1080p) or DTV (1080i) signals are input.
Page 188: Auto Program
Adjusting the LCD Display , ! ’ ENTER • Mono : Choose for channels that are broadcasting in mono or if you are having difficulty receiving a stereo signal. • Stereo : Choose for channels that are broadcasting in stereo. •...
Page 189: Clear Scrambled Channel
Adjusting the LCD Display , ! ’ ENTER ! ’ ENTER The TV automatically cycles through all of the available channels and stores them in memory. In rare cases, "Auto program" may miss a few channels due to weak signals and the channels may not be added to the channel memory.
Page 190 Adjusting the LCD Display • Press the button to select "Channel List", then press the ENTER button to delete the channel. • Press the or button to select All , Added or Favorite , then press the ENTER button. • Press the or button to select Channel, then press the ENTER button.
Page 191 Adjusting the LCD Display mark will appear and the channel will be added. Note All selected channels will be shown on Added menu. Favorite • You can set channels you watch frequently as favorites. D.MENU ! ’ ! ’ ! ’ [Channel] ! ’...
Page 192: Fine Tune
Adjusting the LCD Display , / , ! ’ ENTER! ’ , / , ! ’ ENTER If channel name information is broadcast when you store the channels either manually or automatically, the names are assigned to the channels directly. You can however change these names or assign new names as required.
Page 193 Adjusting the LCD Display channels, you cannot fine tune a digital channel. You can, however, adjust your antenna to improve the reception of available digital channels. If the signal strength meter indicates that the signal is weak, physically adjust your antenna to increase the signal strength.
Page 194: Mpaa Rating
Adjusting the LCD Display ENTER! ’ , ! ’ ENTER • Off / On TV Parental Guidelines D.MENU ! ’ ! ’ ! ’ ! ’ [Setup] ! ’ ENTER ! ’ ! ’ ! ’ ENTER! ’ [V-Chip]! ’ [0~9]! ’...
Page 195: Change Pin
Adjusting the LCD Display , / , ! ’ ENTER Canadian-French D.MENU ! ’ ! ’ ! ’ ! ’ [Setup] ! ’ ENTER ! ’ ! ’ ! ’ ENTER! ’ [V-Chip]! ’ [0~9]! ’ ! ’ ! ’ ! ’...
Page 196: Caption Mode
Adjusting the LCD Display Caption Enables or disables the Caption feature and sets the appearance of closed caption text. D.MENU ! ’ ! ’ ! ’ ! ’ [Setup] ! ’ ENTER ! ’ ! ’ ! ’ ! ’ ENTER! ’...
Page 197: Digital Caption Options
Adjusting the LCD Display • Text3 / Text4 : Third and Fourth Text Services. These data channels should be used only if Text1 and Text2 are not sufficient. Digital Caption Options D.MENU ! ’ ! ’ ! ’ ! ’ [Setup] ! ’...
Page 198 Adjusting the LCD Display • Foreground Color D.MENU ! ’ ! ’ ! ’ ! ’ [Setup] ! ’ ENTER ! ’ ! ’ ! ’ ! ’ ENTER! ’ [Caption] ! ’ ! ’ ! ’ ENTER! ’ [Digital Caption Options] ! ’ ! ’...
Page 199 Adjusting the LCD Display , ! ’ ENTER Default, Transparent, Translucent, Solid, Flashing • Return to Default D.MENU ! ’ ! ’ ! ’ ! ’ [Setup] ! ’ ENTER ! ’ ! ’ ! ’ ! ’ ENTER! ’ [Caption] ! ’...
Page 200: Warning Messages
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check Turn off both your computer and the LCD Display. Unplug the video cable from the back of the computer. Turn on the LCD Display.
Page 201: Check List
Do not use benzene, thinner or other flammable substan- ces, or a wet cloth. • We recommend that a SAMSUNG cleansing agent is used to prevent damage to the screen. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly.
Page 202: Problems Related To The Screen
Troubleshooting PC Mode The LCD Display screen flickers. Check if the signal cable between the computer and the LCD Display is securely connected. (Refer to Connecting a Computer) TV Mode TV screen is blurred or shows noise signals. Check if the TV antenna connector is securely connected to the external antenna.(Refer to Connecting TV) TV signal is not received Select "Auto Program"...
Page 203: Problems Related To Audio
Troubleshooting Check if the resolution and frequency set for the computer video card falls in the range supported by the LCD Display. If not, reset them referring to the current Information under the LCD Display menu and Preset Timing Modes. Ghost images are shown in the picture.
Page 204: Problems Related To The Remote Control
Troubleshooting If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software program. The sound is too high or too low. Adjusts the Treble and Bass to the appropriate levels. Problems related to the Remote Control Note Problems related to the remote control and their solutions are listed.
Page 205 Troubleshooting Set the resolution in the Control Panel ! ’ Appearance and Themes ! ’ Display ! ’ Settings. Windows ME/2000: Set the resolution in the Control Panel ! ’ Display ! ’ Settings. * Contact the video card manufacturer for details. How can I set the Power Saving function? Windows XP: Set the resolution in the Control Panel ! ’...
Page 206 Therefore, to enjoy the full benefits of digital TV, it is better to purchase an HD digital TV. (At present, all digital TVs from Samsung Electronics have the 16:9 wide aspect ratio.) Can I watch digital TV broadcasting with an analog TV? The analog TV cannot interpret digital signals.
Page 207: Specifications
Specifications General General Model Name SyncMaster 400CXN LCD Panel Size 40 " Diagonal (101 cm) Display area 885.17 mm (H) X 497.7 mm (V) Pixel Pitch 0.648 mm (H) X 0.648 mm (V) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 85 Hz Display Color 16.7 M...
Page 208 Specifications VESA Mounting Interface 600 x 400 mm Environmental considerations Operating Temperature : 50°F ~ 104°F (10°C ~ 40°C) Humidity : 10 % ~ 80 %, non-condensing Storage Temperature : -4°F ~ 113°F (-20°C ~ 45°C) Humidity : 5 % ~ 95 %, non-condensing Plug and Play Capability This LCD Display can be installed on any Plug &...
Page 209: Preset Timing Modes
Specifications Item Specification Remarks Office (Word, Excel, Power Point) or PDF documents. Internet Browser MS Internet Explorer Not Support Flash, Java Applet, Security Site Language English Windows XP Embedded MagicInfo Pro - Server Requirement Ethernet OS Application Minimum P1.8 GHz 256 M 100 M / 1 Windows WMP 9 or lat-...
Page 210 Specifications Display Mode Horizontal Vertical Fre- Pixel Clock Sync Polarity Frequency quency (Hz) (MHz) (H/V) (kHz) VESA, 640 x 480 37.500 75.000 31.500 VESA, 800 x 600 35.156 56.250 36.000 VESA, 800 x 600 37.879 60.317 40.000 VESA, 800 x 600 48.077 72.188 50.000...
Page 211 Specifications Display Color 16.7 M Resolution Optimum resolution 1920 x 1080 @ 60 Hz Maximum resolution 1920 x 1080 @ 60 Hz Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB 0.7 Vp-p ±5 % Separate H/V sync, Composite, SOG TTL level (V high "e 2.0 V, V low "d 0.8 V) Maximum Pixel Clock 165MHz (Analog,Digital)
Page 212 Specifications Dot Acceptable TFT-LCD panels manufactured by using advanced semiconductor technology with preci- sion of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen.
Page 213 Specifications PowerSaver This LCD Display has a built-in power management system called PowerSaver. This system saves energy by switching your LCD Display to low-power mode when it has not been used for a certain amount of time. The LCD Display automatically returns to normal operation when you press a key on the keyboard.
Page 214 Specifications Display Mode Horizontal Vertical Fre- Pixel Clock Sync Polarity Frequency quency (Hz) (MHz) (H/V) (kHz) VESA, 1360 x 768 47.712 60.015 85.500 VESA, 1600 x 1200 75.000 60.000 162.000 VESA, 1920 x 1080 66.587 59.934 138.500 Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency.
Page 215: For Better Display
Information For Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT-LCD. •...
Page 216 Information Power Off, Screen Saver, or Power Save Mode • Turn the power off for 4 hours after 20 hours in use • Turn the power off for 2 hours after 12 hours in use • Set the LCD Display to power off with the PC Display Properties Power Scheme. •...
Page 217 Information • Avoid using a combination of characters and background color with large difference in luminance. Avoid using Grey colors, which can cause Image retention easily. Avoid: Colors with big difference in luminance (Black & White, Grey) Change the characters color periodically •...
Page 218 Information Note ( Please check CD's User Guide at "OSD Function", some model's will not available ) Apply the Screen Pixel function on Product • Apply the Screen Pixel function - Symptom: Dot with Black Color move up and down. - Select method •...
Page 219 Information - Select method • Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Eraser • Time Interval : 1 ~ 10 hours ( Recommend : 1 ) • Time Period : 10 ~ 50 second ( Recommend : 50 ) Note ( Please check CD's User Guide at "OSD Function", some model's will not available )
Page 220: Contact Samsung Worldwide
Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG(726-7864) http://www.samsung.com CANADA 1-800-SAMSUNG(726-7864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG(726-7864) http://www.samsung.com Latin America ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 0800-124-421 http://www.samsung.com...
Page 221 Appendix Europe GERMANY 01805 - SAMSUNG (726-7864) http://www.samsung.com (€ 0,14/Min) HUNGARY 06-80-SAMSUNG (726-7864) http://www.samsung.com ITALIA 800-SAMSUNG (726-7864) http://www.samsung.com LUXEMBURG 0035 (0)2 261 03 710 http://www.samsung.com/be NETHERLANDS 0900 SAMSUNG (726-7864 € http://www.samsung.com/nl 0,10/Min) NORWAY 815-56 480 http://www.samsung.com/no POLAND 0 801 801 881 http://www.samsung.com/pl...
Page 222 Appendix Asia Pacific TAIWAN 0800-329-999 http://www.samsung.com/tw VIETNAM 1 800 588 889 http://www.samsung.com Middle East & Africa SOUTH AFRICA 0860-SAMSUNG(726-7864) http://www.samsung.com TURKEY 444 77 11 http://www.samsung.com U.A.E 800-SAMSUNG(726-7864) http://www.samsung.com 8000-4726 Terms Dot Pitch The image on a LCD Display is composed of red, green and blue dots.
Page 223 Channel Fine Tuning This feature allows the viewer to fine-tune the TV channel to ob- tain the best viewing conditions. The Samsung LCD TV has both automatic and manual channel fine-tuning features to enable the viewer to adjust their desired settings.
Page 224: Correct Disposal
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or con- sequential damages in connection with the furnishing, performance, or use of this material.
Page 225 Appendix...

This manual is also suitable for:

Syncmaster 400cxn

Samsung 460CXn - SyncMaster - 46" LCD TV User Manual

LCD Display

User Manual

Also See for Samsung 460CXn - SyncMaster - 46" LCD TV

Related Manuals for Samsung 460CXn - SyncMaster - 46" LCD TV

Summary of Contents for Samsung 460CXn - SyncMaster - 46" LCD TV

This manual is also suitable for:

Comments to this Manuals

Latest comments: