Allied Telesis Rapier Series Release Note
Allied Telesis Rapier Series Release Note

Allied Telesis Rapier Series Release Note

86253-03 patch release note
Hide thumbs Also See for Rapier Series:

Advertisement

Patch Release Note
Patch 86253-03
For Rapier Series Switches
S im ply co nn ecti n g the worl d

Introduction

This patch release note lists the issues addressed and enhancements made in
patch 86253-03 for Software Release 2.5.3 on existing models of Rapier series
switches. Patch file details are listed in Table 1.
Table 1: Patch file details for Patch 86253-03.
Base Software Release File
Patch Release Date
Compressed Patch File Name
Compressed Patch File Size
This release note should be read in conjunction with the following documents:
Release Note: Software Release 2.5.3 for Rapier Switches and AR400 and
AR700 Series Routers (Document Number C613-10362-00 Rev A) available
from www.alliedtelesyn.co.nz/documentation/documentation.html.
Rapier Switch Documentation Set for Software Release 2.5.1 available on
the Documentation and Tools CD-ROM packaged with your switch, or
from www.alliedtelesyn.co.nz/documentation/documentation.html.
WARNING: Using a patch for a different model or software release may cause
unpredictable results, including disruption to the network. Information in this
release note is subject to change without notice and does not represent a
commitment on the part of Allied Telesyn International. While every effort has
been made to ensure that the information contained within this document and
the features and changes described are accurate, Allied Telesyn International
can not accept any type of liability for errors in, or omissions arising from the
use of this information.
86s-253.rez
30-July-2003
86253-03.paz
191102 bytes

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Rapier Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Allied Telesis Rapier Series

  • Page 1 Introduction This patch release note lists the issues addressed and enhancements made in patch 86253-03 for Software Release 2.5.3 on existing models of Rapier series switches. Patch file details are listed in Table 1. This release note should be read in conjunction with the following documents: ■...
  • Page 2 Some of the issues addressed in this Release Note include a level number. This number reflects the importance of the issue that has been resolved. The levels are: Level 1 Level 2 Level 3 Level 4 Features in 86253-03 Patch 86253-03 includes all issues resolved and enhancements released in previous patches for Software Release 2.5.3, and the following enhancements: PCR: 03816 When ports were added or removed as a range with the ENABLE IP IGMP...
  • Page 3 Patch 86253-03 For Rapier Series Switches PCR: 03609 The IP route filter did not always work correctly for OSPF. This issue has been resolved. PCR: 03657 Executing the DISABLE SWITCH PORT command on a port that was the source of a mirror port did not disable the mirror port. This issue has been resolved.
  • Page 4 PCR: 03741 The maximum number of firewall sessions had decreased since software release 86s-241. This issue has been resolved. PCR: 03742 Previously, an incorrect source address was used for router advertisements that were sent over an IPv6 tunnel. The source address of the tunnel (specified by the IPADDRESS parameter of the ADD IPV6 TUNNEL command) was used instead of a link local address.
  • Page 5 Patch 86253-03 For Rapier Series Switches PCR: 03793 The ENABLE RSVP INTERFACE command did not succeed if IP was enabled after the RSVP interface had been created. Now, ENABLE RSVP INTERFACE will succeed regardless of when IP is enabled as long as an IP interface exists.
  • Page 6: Show Ip Igmp

    SHOW IP IGMP Modified Command SHOW IP IGMP Syntax SHOW IP IGMP [COUNTER] [INTERFACE=interface] Description This command displays information about IGMP, and multicast group membership for each IP interface. This enhancement includes the line “Disabled All-groups ports” on the output of this command, as show in Figure 1 on page 6.
  • Page 7: New Commands

    Patch 86253-03 For Rapier Series Switches New Commands This enhancement request introduces two new commands from enabling/ disabling all-group entries on switch ports. ENABLE IP IGMP ALLGROUP Syntax ENABLE IP IGMP ALLGROUP=[{port-list|ALL}] where: ■ port-list is a port number, a range of port numbers (specified as n-m), or a comma separated list of port numbers and/or ranges.
  • Page 8 DISABLE IP IGMP ALLGROUP Patch Release Note Availability Patches can be downloaded from the Software Updates area of the Allied Telesyn web site at www.alliedtelesyn.co.nz/support/updates/patches.html. A licence or password is not required to use a patch. Patch 86253-03 for Software Release 2.5.3 C613-10382-00 REV B...

Table of Contents