Whirlpool WGD9500TC - DUET FRONT LOAD STEAM DRYERS Use And Care Manual page 16

The default dryness setting is Normal when an Auto Dry
Cycle is selected. You can select a different dryness level,
depending on your load, by pressing DRYNESS LEVEL
and choosing More, Normal or Less. Selecting More,
Normal or Less automatically adjusts the dryness level at
which the dryer will shut off. Once a dryness level is set, it
cannot be changed without stopping the cycle.
The Dryness Level can be changed only with Automatic
Cycles.
Press the WRINKLE SHIELD™ feature button if this
option is desired.
Press the CYCLE SIGNAL button to set end of cycle
signal volume to desired level.
Press the DAMP DRY CYCLE SIGNAL button to set damp
dry signal volume to desired level.
Press and hold START button until dryer starts (about
1 second).
Once an Automatic cycle has started, the WRINKLE
SHIELD™ feature and cycle signals can be adjusted. Press
the PAUSE/CANCEL key twice to clear the settings, allowing
you to select another cycle and Dryness Level.
NOTE: Time and Temperature are not adjustable for
Automatic Cycles. Pressing the DRY TIME or TEMPERATURE
buttons will cause a triple beep, indicating that the time
cannot be changed.
How Automatic Cycles Work
The AccelerCare™ function improves drying performance
with Auto Moisture Sensing Plus, which advances the cycle
as moisture is extracted from clothing. A thermistor
(electronic temperature sensor) and moisture sensing strips in
the dryer drum help measure the amount of moisture in the
clothes as they tumble. An electronic control determines the
load type to help save time, avoid overdrying, and increase
the accuracy of the end dryness level. After the first 5 minutes
of an automatic cycle, the estimated time display will adjust
based on the approximate load size, cycle, dryness level
selected and amount of moisture left in the clothes. When the
clothes have reached approximately 80% of the dryness level
selected, the estimated time display will adjust again,
showing the final drying time. The AccelerCare™ feature
takes the guesswork out of drying time and enhances fabric
care.
To use a Manual Cycle
NOTE: A light next to each feature will glow green when the
feature is selected or will glow amber when the feature is
selectable. The light will not glow when the selection is
unavailable with the cycle or option combinations selected.
Press POWER.
Rotate the dial to select a Manual Cycle.
Press the DRY TIME up or down buttons until the desired
drying time is displayed. Press DRY TIME, and the time
will change by 1-minute intervals. Press and hold DRY
TIME, and the time will change by 5-minute intervals. The
initial time displayed is the actual drying time.
The Dry Time feature can be used only with Manual
Cycles and the Enhanced Touch Up Cycle.
16
Press TEMPERATURE until the desired temperature
glows green.
Temperature settings can be changed only with Manual
Cycles.
Press the WRINKLE SHIELD™ feature button if this
option is desired.
Press the CYCLE SIGNAL button to set end of cycle
signal volume to desired level.
Press and hold START button until dryer starts (about
1 second).
NOTE: Dryness Level is not adjustable for Manual or Steam
Cycles. Pressing the Dryness Level button will cause the
triple beep indicating that this option is not selectable.
While a Manual Cycle is running, you cannot change the
cycle until you clear the settings. You can change the settings
for Time, Temperature, the WRINKLE SHIELD™ feature and
the cycle signals. Press the PAUSE/CANCEL key twice to
clear the settings, allowing you to select another cycle.
To use a Steam Cycle
Press the POWER button.
Rotate the dial to select either the Enhanced Touch Up or
Quick Refresh cycles.
Press the DRY TIME up or down buttons until the desired
drying time is displayed. Press DRY TIME, and the time
will change by 1-minute intervals. Press and hold DRY
TIME, and the time will change by 5-minute intervals. The
initial time displayed is the actual drying time
NOTE: The More Time and Less Time buttons can be
used only with Manual Cycles and the Enhanced Touch
Up Cycle.
Press TEMPERATURE until the desired temperature
glows green.
NOTE: During the Enhanced Touch Up Cycle, you can
change the settings for Time, Temperature, the WRINKLE
SHIELD™ feature and Cycle Signal. During the Quick Refresh
Cycle you can change the WRINKLE SHIELD™ feature and
the Cycle Signal. Press STOP twice to stop the dryer and
clear the settings. Select another cycle or option.