Whirlpool  WGD9470WW Product Dimensions

PRODUCT MODEL NUMBERS
WGD9450W, WGD9470W, WGD9550W,
WGD9600T, WGD9750W, WGD9610X
:
Gas supply This dryer is equipped for use with Natural
gas. Dryer can be converted to L.P. gas. When rigid
pipe is used it should be 1/2" IPS. When acceptable
to the gas supplier and local codes, 3/8" approved
tubing may be used for lengths under 20 ft (6.1 m).
For lengths over 20 ft (6.1 m), larger tubing should be
used. Pipe-joint compounds resistant to the action of
L.P. gas must be used. An individual manual shutoff
valve must be installed within 6 ft (1.8 m) of the dryer
in accordance with the National Fuel Gas Code ANSI
Z223.1.
:
Electrical A 120-volt, 60 Hz, AC-only, 15 or 20 amp
fused electrical supply is required for gas dryers, 30
amp for electric dryers. A time-delay fuse or circuit
breaker and a separate circuit are recommended.
:
Water (Steam models only) The dryer must be
connected to the cold water faucet using new inlet
hoses. Do not use old hoses. Do not overtighten.
Damage to the coupling can result.
Exhaust venting :
Exhaust your dryer to the outside.
4" (102 mm) diameter vent is required. Rigid or flexible
metal exhaust vent must be used. Do not use plastic
or metal foil vet. Exhaust hood must be at least
12" (305 mm) from the ground or any object that
may be in the path of the exhaust.
Hood styles: A & B are recommended.
B
(102 mm)
A
4"
A. Louvered hood
(102 mm)
B. Box hood
4"
C. Angled hood (acceptable)
(102 mm)
The vent system chart provides venting requirments
that will help to achieve the best drying performance.
Vent system chart:
NOTE: Side and bottom exhaust installations have
a 90° turn inside the dryer. To determine maximum
exhaust length, add one 90° turn to the chart.
Box or
Number of Type of
o
90 turns vent Louvered
or elbows hoods
0 Rigid metal 64 ft (20 m)
1 Rigid metal 54 ft (16.5 m)
2 Rigid metal 44 ft (13.4 m)
3 Rigid metal 35 ft (10.7 m)
Rigid metal
4 27 ft (8.2 m)
3 / "
7
16
1"
(87 mm)
(25 mm)
14"
(356 mm)
Back View
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Duet Steam and Non-Steam Electronic Gas Dryer
C
4"
2½"
(64 mm)
Angled
hoods
58 ft (17.7 m)
48 ft (14.6 m)
38 ft (11.6 m)
29 ft (8.8 m)
21 ft (6.4 m)
3 / "
3
8
(86 mm)
1"
(25 mm)
7 / "
5
8
(194 mm)
Side View
OVERALL DIMENSIONS
Dryer dimensions
NON-STEAM - 51
38"
(965 mm)
*STEAM - 32 / " 27"
9
16
(827 mm) (686 mm)
†
NON-STEAM - 31 1 / "
2
(800 mm)
For closet installation, with a door, the minimum ventilation openings in the top and
bottom of the door are required. Louvered doors with equivalent air
ventilation openings are acceptable.
3"
(76 mm)
48 in. *
2
(310 cm )
2
24 in. *
2
3"
(155 cm )
2
(76 mm)
NON-STEAM - 31
For dryer on pedestal; cabinet installation, with a door, the minimum ventilation
openings in the top are required.
7"*
(178 mm)
STEAM - 32
(827 mm)
NON-STEAM - 31
(800 mm)
*Required spacing **For side or bottom venting, 0" (0 mm) spacing is allowed.
Select the route that will provide the straightest and most direct path outdoors.
Plan the installation to use the fewest number of elbows and turns.
Use the fewest 90° turns possible.
Do not use vent runs longer than specified in vent length chart.
Determine the number of elbows you will need.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Custom undercounter installation-dryer only
STEAM - 52 / "
9
16
(1335 mm)
/ "
1
2
(1308 mm)
38"
(965 mm)
(25 mm)
Most installations require a minimum
5" (127 mm) clearance behind the dryer for
the exhaust vent with elbow. See Installation
Instructions, "Venting Requirements."
14" max.
(356 mm)
18" max.
(457 mm)
STEAM - 32 / " STEAM - 5 / "**
9 1
16 2
(827 mm) (140 mm)
/ " NON-STEAM - 5"**
1
2
(800 mm) (127 mm)
(178 mm)
14"* max.
(356 mm)
18"* max.
(457 mm)
5"
/ "
9
16
(127 mm)
/ "
1
2
1"* 27" 1"*
(686 mm) (25 mm)
6"
(152 mm)
76"
(1930 mm)
1" 27" 1"
(25 mm) (686 mm) (25 mm)
7"*
9"*
(229 mm)
1"* 27" 1"*
(25 mm) (686 mm) (25 mm)
W10255469B
06/2011