Failed Auto Migration Plan Messages - HP StorageWorks P9000 User Manual

Table 13 Stopped Auto Migration Plan Messages (continued)
Message
The auto migration plan (LDKC:CU:LDEV->LDKC:CU:LDEV)
was stopped. The usage rate of the source volume is over
the specified Max. disk utilization value, or the usage rate
is unknown.
The auto migration plan (LDKC:CU:LDEV->LDKC:CU:LDEV)
was stopped. The migration failed. Error code:
5205-NNNN.
The auto migration plan (LDKC:CU:LDEV->LDKC:CU:LDEV)
was stopped. There is a volume size mismatch between
source and target volumes.
The auto migration plan (LDKC:CU:LDEV->LDKC:CU:LDEV)
was stopped. Unsupported emulation type.
The auto migration plan (LDKC:CU:LDEV->LDKC:CU:LDEV)
was stopped. Failed to check the usage rate of the source
volume.
The auto migration plan (LDKC:CU:LDEV->LDKC:CU:LDEV)
was stopped. Failed to check the target volume.
The auto migration plan (LDKC:CU:LDEV->LDKC:CU:LDEV)
was stopped. An unknown error occurred in checking
target volumes.
The auto migration plan (LDKC:CU:LDEV->LDKC:CU:LDEV)
was stopped. There is an encryption status mismatch
between source and target volumes.

Failed auto migration plan messages

Table 14 (page 33)
The Class X and Group X-X variables in the Message column represent the HDD class and parity
group where the error occurred.
Table 14 Failed Auto Migration Plan Messages
Message
Failed to create auto migration plans. Failed to specify a
proper target volume.
Error location: Class X Group X-X
Failed to create auto migration plans. Insufficient statistics
data in the sampling term.
Error location: Class X Group X-X
Failed to create auto migration plans. Insufficient reserved
volumes.
Error location: Class X Group X-X
lists messages related to failed auto migration plans.
Description
The disk usage rate of the parity group including the source
volume is over the specified limit. Or, the disk usage rate
is unknown. If applicable, increase the Max. disk utilization
value in the Auto Plan Parameters section of the Auto Plan
window and reinstate the auto migration plan.
The migration plan failed due to an error indicated by the
error code. '5205' is the part code for Auto LUN and
'NNNN' represents the error number. For information on
the error and recommended action, see the HP
StorageWorks P9000 Remote Web Console Messages
document.
The size of the source volume is different from that of the
target volume. The volume configuration might have been
changed after the creation of the auto migration plan.
The emulation type of the specified target volume is not
supported. The volume configuration might have been
changed after the creation of the auto migration plan.
The check of the disk usage rate of the parity group
including the source volume ended abnormally. Contact
the service engineer for information on resolving this issue.
The check of the target volume ended abnormally. Contact
the service engineer for information on resolving this issue.
An unknown error occurred while checking the target
volume. Contact the service engineer for information on
resolving this issue.
The encryption status of the source volume is different from
that of the target volume. The volume configuration might
have been changed after the creation of the auto migration
plan.
Description
Auto LUN could not specify a proper target volume for
creating an auto migration plan.
There are insufficient data for creating auto migration
plans. Check the Sampling Term and Number of Sampling
Points settings in the Auto Plan window to see if monitoring
data is being properly acquired. Make any necessary
adjustments and attempt to collect the data again.
There is an insufficient amount of reserved volumes for
creating auto migration plans. If Auto LUN failed to obtain
the specified information, check the Reserve volumes in the
Attribute window.
Auto migration messages 33