HP P6000 Replacement Instructions
Hp p6300/p6500 eva fibre channel controller enclosure replacement instructions (593088-001, june 2011)
Hide thumbs
Also See for P6000:
- User manual (104 pages) ,
- Installation manual (74 pages) ,
- Installation instructions manual (17 pages)
Advertisement
Quick Links
HP P6300/P6500 EVA Fibre
Channel Controller Enclosure
Replacement Instructions
© Copyright 2011 Hewlett-Packard Development Company, L.P.
First edition: May 2011
The information in this document is subject to change without notice.
Printed in Puerto Rico
www.hp.com
*593088-001*
About this document
For the latest documentation, go to
manuals, and select your product.
The information contained herein is subject to change without notice.
The only warranties for HP products and services are set forth in the
express warranty statements accompanying such products and services.
Nothing herein should be construed as constituting an additional
warranty. HP shall not be liable for technical or editorial errors or
omissions contained herein.
WARRANTY STATEMENT: To obtain a copy of the warranty for this
product, see the warranty information website:
http://www.hp.com/go/storagewarranty
Choosing a storage configuration
The P6300 EVA configuration details are:
Two HSV340 controllers per controller enclosure
Four SAS ports
Four 8 Gb FC ports per controller
1/10 (minimum/maximum) controller enclosures
8/120 (minimum/maximum) M6612 (LFF) disk drives
8/250 (minimum/maximum) M6625 (SFF) disk drives
The P6500 EVA configuration details are:
Two HSV360 controllers per controller enclosure
Eight SAS ports
Four 8 Gb FC ports per controller
2/20 (minimum/maximum) controller enclosures
8/240 (minimum/maximum) M6612 (LFF) disk drives
8/450 (minimum/maximum) M6625 (SFF) disk drives
Before you begin
Observe the following precautions when replacing a controller.
CAUTION:
HP recommends that you perform the replacement procedure
within seven minutes from when the controller is removed to
when it is replaced in the enclosure. Ensure all necessary parts
are available so the procedure can be completed without
interruption. Removing a controller module significantly changes
the air flow within the enclosure. Both controllers must be
installed for the enclosure to cool properly. If a controller fails,
leave it in place in the enclosure until a new module is available
to install. The enclosure could shut down due to overheating
unless the controller is replaced within the recommended seven
minutes.
Parts can be damaged by electrostatic discharge. Use proper
anti-static protection. See the documentation that shipped with
your system for additional information.
Page 1
http://www.hp.com/support/
Advertisement
Related Manuals for HP P6000
Summary of Contents for HP P6000
-
Page 1: Before You Begin
The P6500 EVA configuration details are: Two HSV360 controllers per controller enclosure Eight SAS ports Four 8 Gb FC ports per controller © Copyright 2011 Hewlett-Packard Development Company, L.P. 2/20 (minimum/maximum) controller enclosures First edition: May 2011 8/240 (minimum/maximum) M6612 (LFF) disk drives 8/450 (minimum/maximum) M6625 (SFF) disk drives The information in this document is subject to change without notice. -
Page 2: Verifying Component Failure
Halt I/O to the controller with HP P6000 Command View: In the navigation pane, select Storage System > Hardware > Figure 2 Controller status LEDs Controller Enclosure. -
Page 3: Installing A Controller
Remove the controller. Press the retaining clips outward to unlock each DIMM socket (1, Figure 6). This action releases the modules, and partially lifts the Loosen the thumbscrew on the mounting latch and rotate the modules out of the socket. latch to the right (1, Figure 3). - Page 4 Verify the controller health green LED is lit (see Table 1). If not, try reseating the controller in the enclosure. From HP P6000 Command View, navigate to the component as de- scribed in the Verifying component failure section, and check the status.